STARTUP    =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
            ALIGNMENT/END
            MODE/MANUAL
            MOVESPEED/ 300
            TOUCHSPEED/ 4.5
            MANRETRACT/0.7874
            FLY/ON,0.1181
            FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;MEAS,NOM,TOL,DEV,OUTTOL, , 
            LOADPROBE/4X60 MF
            TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
CYL1       =FEAT/CYLINDER,CARTESIAN,IN,LEAST_SQR
            THEO/<0,0,-0.2218>,<0,0,1>,0.8755,0.2609
            ACTL/<31.4073,55.0399,-29.6306>,<0.0239901,0.0062781,0.9996925>,0.876,0.2005
            MEAS/CYLINDER,6
              HIT/BASIC,NORMAL,<0.0019,0.4377,-0.3523>,<-0.0042731,-0.9999909,0>,<31.4228,55.477,-29.7232>,USE THEO=YES
              HIT/BASIC,NORMAL,<-0.337,-0.2793,-0.348>,<0.7699596,0.6380927,0>,<31.0622,54.7667,-29.7209>,USE THEO=YES
              HIT/BASIC,NORMAL,<0.3847,-0.2089,-0.3349>,<-0.8787256,0.4773272,0>,<31.8432,55.0386,-29.7245>,USE THEO=YES
              HIT/BASIC,NORMAL,<-0.0063,0.4377,-0.1892>,<0.0144723,-0.9998953,0>,<31.4357,55.4771,-29.6072>,USE THEO=YES
              HIT/BASIC,NORMAL,<-0.0138,0.4375,-0.0975>,<0.0315008,-0.9995037,0>,<31.4354,55.4778,-29.5337>,USE THEO=YES
              HIT/BASIC,NORMAL,<-0.0281,-0.4368,-0.0914>,<0.0642381,0.9979346,0>,<31.4354,54.6032,-29.5328>,USE THEO=YES
            ENDMEAS/
PLN1       =FEAT/PLANE,CARTESIAN,OUTLINE
            THEO/<-0.0066,-0.005,0>,<0,0,1>
            ACTL/<31.4055,55.0338,-29.3859>,<0.0112207,0.0073354,0.9999101>
            MEAS/PLANE,3
              HIT/BASIC,NORMAL,<-0.0485,0.488,0>,<0,0,1>,<30.9716,54.7916,-29.3792>,USE THEO=YES
              HIT/BASIC,NORMAL,<-0.41,-0.2739,0>,<0,0,1>,<31.8015,54.7916,-29.3885>,USE THEO=YES
              HIT/BASIC,NORMAL,<0.4386,-0.2292,0>,<0,0,1>,<31.4433,55.5182,-29.3898>,USE THEO=YES
            ENDMEAS/
A1         =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
              ALIGNMENT/LEVEL,ZPLUS,CYL1
              ALIGNMENT/TRANS,XAXIS,CYL1
              ALIGNMENT/TRANS,YAXIS,CYL1
              ALIGNMENT/TRANS,ZAXIS,PLN1
            ALIGNMENT/END
            COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,
            WARNING!!
            Ready to start
            DCC Mode.
            Move probe
            above part.
            MODE/DCC
CYLA       =FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<0,0,-0.425>,<0,0,1>,0.8755,-0.425
            ACTL/<0.0033,0.0189,-0.4251>,<-0.0040145,0.0046047,0.9999813>,0.8756,-0.425
            TARG/<0,0,-0.425>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=8,NUMLEVELS=3,DEPTH=0.125,END OFFSET=0.1,PITCH=0
              SAMPLE METHOD=SAMPLE_FEATURE
              SAMPLE FEATURE=NONE
              AVOIDANCE MOVE=BOTH,DISTANCE=0.25
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
PLN2       =FEAT/CONTACT/PLANE/DEFAULT,CARTESIAN,NONE
            THEO/<0,0,0>,<0,0,1>
            ACTL/<0.0004,-0.0001,0.0113>,<-0.0047218,0.0032854,0.9999835>
            TARG/<0,0,0>,<0,0,1>
            ANGLE VEC=<1,0,0>,RADIAL
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=6,NUMRINGS=1
              SPACER=0.494
              AVOIDANCE MOVE=NO,DISTANCE=0.25
              USE BOUNDARY OFFSET=YES,OFFSET=40.3225
            SHOW HITS=NO
AUTO ALIGNMENT=ALIGNMENT/START,RECALL:STARTUP,LIST=YES
              ALIGNMENT/LEVEL,ZPLUS,CYLA
              ALIGNMENT/TRANS,XAXIS,CYLA
              ALIGNMENT/TRANS,YAXIS,CYLA
              ALIGNMENT/TRANS,ZAXIS,PLN2
            ALIGNMENT/END
            DATDEF/FEATURE=CYLA,A
DIM LOC1= LOCATION OF CYLINDER CYLA  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X       0.0000     0.0000     0.0050     0.0050     0.0000     0.0000 ----#----
Y       0.0000     0.0000     0.0050     0.0050     0.0000     0.0000 ----#----
D       0.8756     0.8755     0.0025     0.0025     0.0001     0.0000 ----#----
END OF DIMENSION LOC1
0.660 CYL  =FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<0,0,-1.32>,<0,0,1>,0.66,-0.895
            ACTL/<0.0016,0.0004,-1.32>,<-0.0019392,-0.0002789,0.9999981>,0.6622,-0.895
            TARG/<0,0,-1.32>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=8,NUMLEVELS=3,DEPTH=0.125,END OFFSET=0.125,PITCH=0
              SAMPLE METHOD=SAMPLE_FEATURE
              SAMPLE FEATURE=NONE
              AVOIDANCE MOVE=BOTH,DISTANCE=0.25
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
DIM LOC2= LOCATION OF CYLINDER 0.660 CYL  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X       0.0016     0.0000     0.0035     0.0035     0.0016     0.0000 ------#--
Y       0.0004     0.0000     0.0035     0.0035     0.0004     0.0000 -----#---
D       0.6622     0.6600     0.0100     0.0100     0.0022     0.0000 -----#---
END OF DIMENSION LOC2
FCFRNOUT1 =CIRCULAR RUNOUT : 0.660 CYL
            FEATCTRLFRAME/SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=10.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=IN
            CUSTOMIZED DRF=NO
            STANDARDTYPE=ASME_Y14_5
              DIMENSION/CIRCULAR RUNOUT,RADIAL,0.01,A
              NOTE/FCFRNOUT1
            FEATURES/0.660 CYL,,
THREAD DIAMETER=FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,OUT,LEAST_SQR
            THEO/<0,0,-0.55>,<0,0,1>,1.024,0.55
            ACTL/<-0.0009,0.0009,-0.55>,<-0.0002631,-0.001973,0.999998>,1.1198,0.55
            TARG/<0,0,-0.55>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=4,NUMLEVELS=2,DEPTH=0.1875,END OFFSET=0.125,PITCH=0.0833
              SAMPLE METHOD=SAMPLE_FEATURE
              SAMPLE FEATURE=NONE
              AVOIDANCE MOVE=AFTER,DISTANCE=0.25
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
FCFLOC1 =POSITION : THREAD DIAMETER
            FEATCTRLFRAME/SHOWNOMS=NO,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=10.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=IN
            COMPOSITE=NO,FIT TO DATUMS=YES,DEV PERPEN CENTERLINE=ON,OUTPUT ALIGNMENT=Datum Reference Frame
            CUSTOMIZED DRF=NO
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,1.116,0.007,0.007
              PRIMARY DIMENSION/POSITION,DIAMETER,0.01,<MC>,<PZ>,<len>,A,<MC>,<dat>,<dat>
              SECONDARY DIMENSION/<Dim>,<tol>,<MC>,<dat>,<dat>,<dat>
              NOTE/FCFLOC1
            FEATURES/THREAD DIAMETER,,
            MOVE/INCREMENT,<0,0,4>
            TIP/T1A90B90, SHANKIJK=-0.9995, 0, -0.0324, ANGLE=88.9242
RIGHT EAR  =FEAT/CONTACT/PLANE/DEFAULT,CARTESIAN,NONE
            THEO/<-0.3869,-0.29,-2.197>,<0,1,0>
            ACTL/<-0.3865,-0.309,-2.197>,<-0.0229286,0.9997371,-0.0000199>
            TARG/<-0.3869,-0.29,-2.197>,<0,1,0>
            ANGLE VEC=<-1,0,0>,RADIAL
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=6,NUMRINGS=1
              SPACER=0.494
              AVOIDANCE MOVE=NO,DISTANCE=0.25
            SHOW HITS=NO
DIM LOC3= LOCATION OF PLANE RIGHT EAR  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
Y      -0.3044    -0.2900     0.0100     0.0100    -0.0144     0.0044 <--------
END OF DIMENSION LOC3
FCFPARL1 =PARALLELISM : RIGHT EAR
            FEATCTRLFRAME/SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=10.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=IN
            STANDARDTYPE=ASME_Y14_5
              DIMENSION/PARALLELISM,0.015,<PZ>,<type>,<len>,<wid>,A,<MC>,<dat>,<dat>
              NOTE/FCFPARL1
            FEATURES/RIGHT EAR,,
LEFT EAR   =FEAT/CONTACT/PLANE/DEFAULT,CARTESIAN,NONE
            THEO/<-0.5146,0.29,-2.4627>,<0,-1,0>
            ACTL/<-0.5141,0.271,-2.4626>,<0.0258454,-0.99965,0.0056447>
            TARG/<-0.5146,0.29,-2.4627>,<0,-1,0>
            ANGLE VEC=<1,0,0>,RADIAL
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=6,NUMRINGS=1
              SPACER=0.494
              AVOIDANCE MOVE=NO,DISTANCE=0.25
            SHOW HITS=NO
DIM LOC4= LOCATION OF PLANE LEFT EAR  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
Y       0.2759     0.2900     0.0100     0.0100    -0.0141     0.0041 <--------
END OF DIMENSION LOC4
FCFPARL2 =PARALLELISM : LEFT EAR
            FEATCTRLFRAME/SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=10.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=IN
            STANDARDTYPE=ASME_Y14_5
              DIMENSION/PARALLELISM,0.015,<PZ>,<type>,<len>,<wid>,A,<MC>,<dat>,<dat>
              NOTE/FCFPARL2
            FEATURES/LEFT EAR,,
WIDTH OF NOTCH=FEAT/WIDTH,CARTESIAN,IN,LEAST_SQR,NO
            THEO/<-0.1995,0,-2.9469>,<0,1,0>,0.58
            MEAS/<-0.1987,-0.0142,-2.9708>,<-0.0244,0.9997,-0.003>,0.5808
            CONSTR/WIDTH,BFRE,RIGHT EAR,LEFT EAR
DIM LOC5= LOCATION OF 3D WIDTH WIDTH OF NOTCH  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
Y      -0.0142     0.0000     0.0100     0.0100    -0.0142     0.0042 <--------
L       0.5808     0.5800     0.0100     0.0100     0.0008     0.0000 ----#----
END OF DIMENSION LOC5
            MOVE/INCREMENT,<-4,0,0>
            MOVE/INCREMENT,<0,-4.592,11.087>
            TIP/T1A-90B0, SHANKIJK=0.0006, -0.9998, -0.0188, ANGLE=1.8549
            WORKPLANE/YMINUS
0.500 CYL  =FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<0,0.675,-2.39>,<0,-1,0>,0.4995,-1.35
            ACTL/<-0.0139,0.6747,-2.3963>,<0.0164816,-0.9998637,0.0009663>,0.4975,-1.35
            TARG/<0,0.675,-2.39>,<0,-1,0>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=8,NUMLEVELS=2,DEPTH=0.1875,END OFFSET=0.1875,PITCH=0
              SAMPLE METHOD=SAMPLE_FEATURE
              SAMPLE FEATURE=NONE
              AVOIDANCE MOVE=BEFORE,DISTANCE=0.25
              FIND HOLE=CENTER,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
DIM LOC6= LOCATION OF CYLINDER 0.500 CYL  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X      -0.0139     0.0000     0.0300     0.0300    -0.0139     0.0000 --#------
Z      -2.3963    -2.3900     0.0100     0.0100    -0.0063     0.0000 -#-------
D       0.4975     0.4995     0.0015     0.0015    -0.0020     0.0005 <--------
END OF DIMENSION LOC6
FCFPERP1 =PERPENDICULARITY : 0.500 CYL
            FEATCTRLFRAME/SHOWNOMS=NO,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=10.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=IN
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,0.4995,0.0015,0.0015
              DIMENSION/PERPENDICULARITY,<D>,0.01,<PZ>,<len>,A,<MC>,<dat>,<dat>
              NOTE/FCFPERP1
            FEATURES/0.500 CYL,,
0.500 CIR  =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<0,-0.675,-2.39>,<0,-1,0>,0.4995
            ACTL/<0.0054,-0.675,-2.3952>,<0,-1,0>,0.5026
            TARG/<0,-0.675,-2.39>,<0,-1,0>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=4,DEPTH=0.18,PITCH=0
              SAMPLE METHOD=SAMPLE_FEATURE
              SAMPLE FEATURE=NONE
              AVOIDANCE MOVE=AFTER,DISTANCE=0.25
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
DIM LOC9= LOCATION OF CIRCLE 0.500 CIR  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X       0.0054     0.0000     0.0300     0.0300     0.0054     0.0000 -----#---
Z      -2.3952    -2.3900     0.0100     0.0100    -0.0052     0.0000 --#------
D       0.5026     0.4995     0.0015     0.0015     0.0031     0.0016 -------->
END OF DIMENSION LOC9
0.250 CYL  =FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<0,0.54,-3.41>,<0,-1,0>,0.25,-1.08
            ACTL/<-0.017,0.5397,-3.4179>,<0.0180065,-0.9998339,0.0028348>,0.2481,-1.08
            TARG/<0,0.54,-3.41>,<0,-1,0>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=8,NUMLEVELS=2,DEPTH=0.125,END OFFSET=0.125,PITCH=0
              SAMPLE METHOD=SAMPLE_FEATURE
              SAMPLE FEATURE=NONE
              AVOIDANCE MOVE=BEFORE,DISTANCE=0.25
              FIND HOLE=CENTER,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
DIM LOC7= LOCATION OF CYLINDER 0.250 CYL  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X      -0.0170     0.0000     0.0300     0.0300    -0.0170     0.0000 -#-------
Z      -3.4179    -3.4100     0.0100     0.0100    -0.0079     0.0000 #--------
D       0.2481     0.2500     0.0010     0.0010    -0.0019     0.0009 <--------
END OF DIMENSION LOC7
FCFPERP2 =PERPENDICULARITY : 0.250 CYL
            FEATCTRLFRAME/SHOWNOMS=NO,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=10.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=IN
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,0.25,0.001,0.001
              DIMENSION/PERPENDICULARITY,<D>,0.01,<PZ>,<len>,A,<MC>,<dat>,<dat>
              NOTE/FCFPERP2
            FEATURES/0.250 CYL,,
DIM DIST1= 2D DISTANCE FROM CYLINDER 0.500 CYL TO CYLINDER 0.250 CYL     (CENTER TO CENTER),NO_RADIUS  UNITS=IN,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
M       1.0216     1.0200     0.0100     0.0100     0.0016     0.0000 -----#---
CIR1       =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<0,-0.54,-3.41>,<0,-1,0>,0.25
            ACTL/<0.0005,-0.54,-3.4153>,<0,-1,0>,0.2526
            TARG/<0,-0.54,-3.41>,<0,-1,0>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=4,DEPTH=0.118,PITCH=0
              SAMPLE METHOD=SAMPLE_FEATURE
              SAMPLE FEATURE=NONE
              AVOIDANCE MOVE=AFTER,DISTANCE=0.25
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
DIM LOC10= LOCATION OF CIRCLE CIR1  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X       0.0005     0.0000     0.0300     0.0300     0.0005     0.0000 ----#----
Z      -3.4153    -3.4100     0.0100     0.0100    -0.0053     0.0000 --#------
D       0.2526     0.2500     0.0010     0.0010     0.0026     0.0016 -------->
END OF DIMENSION LOC10
            MOVE/INCREMENT,<0,-4.592,11.087>
            TIP/T1A0B0, SHANKIJK=-0.0324, -0.0188, 0.9993, ANGLE=0
            LOADPROBE/1X20SF
            TIP/T1A0B0, SHANKIJK=-0.0324, -0.0188, 0.9993, ANGLE=0
            WORKPLANE/ZPLUS
COUNTERBORE PLANE=FEAT/CONTACT/PLANE/DEFAULT,CARTESIAN,NONE
            THEO/<0,0,-0.425>,<0,0,1>
            ACTL/<0,0.0003,-0.4278>,<-0.0014211,0.0000346,0.999999>
            TARG/<0,0,-0.425>,<0,0,1>
            ANGLE VEC=<1,0,0>,RADIAL
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=6,NUMRINGS=1
              SPACER=0.378
              AVOIDANCE MOVE=NO,DISTANCE=0.25
            SHOW HITS=NO
DIM LOC8= LOCATION OF PLANE COUNTERBORE PLANE  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
Z      -0.4278    -0.4250     0.0050     0.0050    -0.0028     0.0000 --#------
END OF DIMENSION LOC8
            MOVE/INCREMENT,<0,0,5>
            LOADPROBE/4X60 MF
            TIP/T1A0B0, SHANKIJK=-0.0324, -0.0188, 0.9993, ANGLE=0
            MOVE/CLEARPOINT