PART NAME  :  
REV NUMBER : 
SER NUMBER : 
STATS COUNT : 43
GD&T STANDARD : ISO 1101 - 2012/2017
 
START      =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
            ALIGNMENT/END
            STATS/ON,DATAPAGE+,,OFFLINE=YES
            RECORD=ALL
            WORKPLANE/ZPLUS
            PREHIT/3
            RETRACT/3
            MANRETRACT/2
            MOVESPEED/ 150
            TOUCHSPEED/ 3
            FORMAT/TEXT,OPTIONS,ID,HEADINGS,SYMBOLS, ;NOM,MEAS,TOL,DEV,OUTTOL, , 
            DISPLAYPRECISION/3
$$ NO,
            **************************************** PROGRAM LOG ********************************************

$$ NO,
            ******************************** PART  INFORMATION - LINK IMAGES - PROBE PARAMETER SET  *********
            ASSIGN/PART_NO=""
            ASSIGN/CUSTOMER=""
            ASSIGN/CUSTOMER_DWG="10080727"
            ASSIGN/CUSTOMER_DWG_REV="00D"
            ASSIGN/CUSTOMER_PART_NO=""
            ASSIGN/DESCRIPTION=""
            COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
            THIS PROGRAM USE TIP: 5.0 X 50 AND 1 X 20 X 20EXT ANALOG PROBE (SCANNING PROBE)
            ???????:5.0 X 50 - 1 X 20 X 20 EXT
QUALIFY    =COMMENT/YESNO,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
            WOULD YOU LIKE TO QUALIFY THE TIP ?
            IF_GOTO/QUALIFY.INPUT=="YES",GOTO = QUALIFICATION
            IF_GOTO/QUALIFY.INPUT=="NO",GOTO = INPUT
QUALIFICATION=LABEL/
            COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
            MOVE THE TIP TO THE SAFE POSITION (CENTER - UP - BACK)
             
            SLOW DOWN THE MACHINE SPEED AND PLACE THE MASTER
             
            SPHERE ON TIP QUALIFICATION POSITION.
            LOADPROBE/X1H-5X50
            TIP/T1A0B0, SHANKIJK=0, -1, 0, ANGLE=0
            AUTOCALIBRATE/PROBE, PARAMETER_SET=A0B0_Primary, QUALTOOL_MOVED=NO, 
                          CHECK COLLISION=NO, SHOW_SUMMARY=NO, OVERWRITE_RESULTSFILE=NO
            AUTOCALIBRATE/PROBE, PARAMETER_SET=230608-01, QUALTOOL_MOVED=NO, 
                          CHECK COLLISION=NO, SHOW_SUMMARY=NO, OVERWRITE_RESULTSFILE=NO
            LOADPROBE/X1H-1X20X20EXT
            TIP/T1A0B0, SHANKIJK=0, -1, 0, ANGLE=0
            AUTOCALIBRATE/PROBE, PARAMETER_SET=230608-01, QUALTOOL_MOVED=NO, 
                          CHECK COLLISION=NO, SHOW_SUMMARY=NO, OVERWRITE_RESULTSFILE=NO
            COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
            MOVE THE MACHINE TO THE SAFE POSITION (CENTER - UP - BACK)
                        
            AND REMOVE THE MASTER SPHERE
$$ NO,
            ******************************** PART  INFORMATION - LINK IMAGES - PROBE PARAMETER SET  *********

$$ NO,
            ******************************** SETUP READPOINT OR MANUAL ALIGMENT - LINK IMAGES   ************
SETUP      =LABEL/
            MODE/MANUAL
            LOADPROBE/X1H-5X50
            TIP/T1A0B0, SHANKIJK=0, -1, 0, ANGLE=0
            COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
            SET UP THE FIXTURE 
            
            AS SHOWN IN THE PICTURE.
ANSICHT_MAN =VIEWSET/
            RECALL/VIEWSET,ANSICHT_MAN
            COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
            TAKE THREE POINTS ON DATUM A
PNT_A1_MAN =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
            THEO/<3908.023,11.567,72.403>,<-0.7093432,-0.6970696,0.1045285>
            ACTL/<76.205,357.179,309.395>,<0.0139251,-0.9994535,0.0299801>
            TARG/<3908.023,11.567,72.403>,<-0.7093432,-0.6970696,0.1045285>
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=4,DISTANCE AFTER=4,DIRECTION=ALONG FEATURE VECTOR
            SHOW HITS=NO
PNT_A2_MAN =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
            THEO/<3868.183,42.931,11.201>,<-0.7093432,-0.6970696,0.1045285>
            ACTL/<8.573,357.268,216.025>,<0.0108786,-0.9995755,0.0270285>
            TARG/<3868.183,42.931,11.201>,<-0.7093432,-0.6970696,0.1045285>
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=4,DISTANCE AFTER=4,DIRECTION=ALONG FEATURE VECTOR
            SHOW HITS=NO
PNT_A3_MAN =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
            THEO/<3944.515,-37.81,-9.234>,<-0.7093432,-0.6970696,0.1045285>
            ACTL/<116.708,357.206,212.157>,<0.0144312,-0.9996251,0.023266>
            TARG/<3944.515,-37.81,-9.234>,<-0.7093432,-0.6970696,0.1045285>
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=4,DISTANCE AFTER=4,DIRECTION=ALONG FEATURE VECTOR
            SHOW HITS=NO
PLANE_A_MAN=FEAT/PLANE,CARTESIAN,TRIANGLE,NO,LEAST_SQR
            THEO/<3906.907,5.563,24.79>,<0.7093432,0.6970696,-0.1045285>
            ACTL/<67.162,357.217,245.859>,<0.000592,0.9999997,0.0005199>
            CONSTR/PLANE,BF,PNT_A1_MAN,PNT_A2_MAN,PNT_A3_MAN,,
            OUTLIER_REMOVAL/OFF,3
            FILTER/OFF,WAVELENGTH=0
A_MAN      =ALIGNMENT/START,RECALL:START,LIST=YES
              ALIGNMENT/LEVEL,ZMINUS,PLANE_A_MAN
              ALIGNMENT/TRANS,ZAXIS,PLANE_A_MAN
            ALIGNMENT/END
            COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
            TAKE THREE POINTS ON DATUM B
CIR_B_MAN  =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<2752.673,15.427,-2.2>,<0,0,1>,90.05
            ACTL/<62.52,247.613,-2.2>,<0,0,1>,90.127
            TARG/<2752.673,15.427,-2.2>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<0.2068276,0.9783774,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=NO
            COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
            TAKE THREE POINTS ON DATUM J
            MANRETRACT/0.5
CIR_J_MAN  =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<2741.661,-10.425,-29.5>,<0,0,1>,6.1
            ACTL/<53.976,220.846,-29.5>,<0,0,1>,7.269
            TARG/<2741.661,-10.425,-29.5>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<0.2068276,0.9783774,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=NO
ABJ_MAN    =ALIGNMENT/START,RECALL:A_MAN,LIST=YES
              ALIGNMENT/LEVEL,ZMINUS,PLANE_A_MAN
              ALIGNMENT/TRANS,ZAXIS,PLANE_A_MAN
              ALIGNMENT/ROTATE_CIRCLE,YMINUS,TO,CIR_B_MAN,AND,CIR_J_MAN,ABOUT,ZPLUS
              ALIGNMENT/TRANS,XAXIS,CIR_B_MAN
              ALIGNMENT/TRANS,YAXIS,CIR_B_MAN
              ALIGNMENT/ROTATE_OFFSET,17,ABOUT,ZPLUS
            ALIGNMENT/END

$$ NO,
            ****************************************** M E A S U R E M E N T   R O U T I N E  ***********************
START      =LABEL/
            RECALL/ALIGNMENT,INTERNAL,ABJ_MAN
            MODE/DCC
            PREHIT/3
            RETRACT/3
            WORKPLANE/ZPLUS
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<0,0,10>
PLN_A_INITIAL=FEAT/CONTACT/PLANE/ADAPTIVE_PLANE_CIRCLE_SCAN,CARTESIAN,OUTLINE,LEAST_SQR
            THEO/<0,0,0>,<0,0,1>
            ACTL/<-0.546,-1.424,0.012>,<-0.0000364,0.0000064,1>
            TARG/<0,0,0>,<0,0,1>
            ANGLE VEC=<1,0,0>,RADIAL
            SHOW FEATURE PARAMETERS=YES
              VOID DETECTION=YES
              SURFACE=THICKNESS_NONE,0
              MEASURE MODE=NOMINALS
              RMEAS=NONE,NONE,NONE
              AUTO WRIST=NO
              CIRCULAR MOVES=CIRCULAR
              GRAPHICAL ANALYSIS=NO
              FEATURE LOCATOR=NO,NO,""
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=2999,NUMRINGS=2
              SPACER=33
              AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0,DISTANCE AFTER=0,DIRECTION=ALONG FEATURE VECTOR
              USE BOUNDARY OFFSET=NO
            SHOW HITS=NO
A_INITIAL  =ALIGNMENT/START,RECALL:ABJ_MAN,LIST=YES
              ALIGNMENT/LEVEL,ZPLUS,PLN_A_INITIAL
              ALIGNMENT/TRANS,ZAXIS,PLN_A_INITIAL
            ALIGNMENT/END
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<0,0,10>
CYL_B_INITIAL=FEAT/CONTACT/CYLINDER/ADAPTIVE_CYLINDER_SPIRAL_SCAN,CARTESIAN,IN,MAX_INSC
            THEO/<0,0,-18.7>,<0,0,1>,89.05,8.8
            ACTL/<0.008,-0.012,-18.7>,<0.0006207,-0.00037,0.9999997>,89.079,8.8
            TARG/<0,0,-18.7>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<0.1021822,0.9947657,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=2912,NUMLEVELS=3,DEPTH=2,END OFFSET=1,PITCH=2.5
              SAMPLE METHOD=SAMPLE_HITS
              SAMPLE HITS=0,SPACER=0
              AVOIDANCE MOVE=NO
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
AB_INITIAL =ALIGNMENT/START,RECALL:A_INITIAL,LIST=YES
              ALIGNMENT/LEVEL,ZPLUS,PLN_A_INITIAL
              ALIGNMENT/TRANS,XAXIS,CYL_B_INITIAL
              ALIGNMENT/TRANS,YAXIS,CYL_B_INITIAL
              ALIGNMENT/TRANS,ZAXIS,PLN_A_INITIAL
            ALIGNMENT/END
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<50,0,50>
            MOVE/POINT,NORMAL,<50,0,50>
            TIP/T1A45B-90, SHANKIJK=1, 0.001, -0.009, ANGLE=-84
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<0,0,10>
SPH_1A_TEMP1=FEAT/CONTACT/SPHERE/DEFAULT,POLAR,IN,LEAST_SQR
            THEO/<41.6,180,-13.6>,<1,0,0>,14.8
            ACTL/<41.639,180.003,-13.596>,<1,0,0>,14.868
            TARG/<41.6,180,-13.6>,<1,0,0>
            START ANGLE 1=0,END ANG 1=360
            START ANGLE 2=-90,END ANG 2=-40
            ANGLE VEC=<-0.0086787,0,-0.9999623>
            SHOW FEATURE PARAMETERS=YES
              SURFACE=THICKNESS_NONE,0
              MEASURE MODE=NOMINALS
              RMEAS=NONE,NONE,NONE
              AUTO WRIST=NO
              GRAPHICAL ANALYSIS=NO
              FEATURE LOCATOR=NO,NO,""
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=11,NUMROWS=3
              AVOIDANCE MOVE=NO
            SHOW HITS=NO
ABSPH1ATEMP1=ALIGNMENT/START,RECALL:AB_INITIAL,LIST=YES
              ALIGNMENT/ROTATE_CIRCLE,XMINUS,TO,CYL_B_INITIAL,AND,SPH_1A_TEMP1,ABOUT,ZPLUS
            ALIGNMENT/END
P_C1_INITIAL=FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
            THEO/<-45.36,-6.374,-13.6>,<0.5080827,0.8613083,0>
            ACTL/<-45.401,-6.432,-13.602>,<0.5080827,0.8613083,0>
            TARG/<-45.36,-6.374,-13.6>,<0.5080827,0.8613083,0>
            SNAP=NO
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=NO
P_C2_INITIAL=FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
            THEO/<-45.36,6.374,-13.6>,<0.5080827,-0.8613083,0>
            ACTL/<-45.403,6.439,-13.607>,<0.5080827,-0.8613083,0>
            TARG/<-45.36,6.374,-13.6>,<0.5080827,-0.8613083,0>
            SNAP=NO
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=NO
POINT_C_INITIAL=FEAT/POINT,CARTESIAN,NO
            THEO/<-45.36,0,-13.6>,<0,1,0>
            ACTL/<-45.402,0.004,-13.605>,<0.0069611,0.9999751,-0.0011604>
            CONSTR/POINT,MID,P_C1_INITIAL,P_C2_INITIAL
LINE_C_INITIAL=FEAT/LINE,CARTESIAN,UNBOUNDED,NO
            THEO/<0,0,-13.6>,<-1,0,0>
            ACTL/<0.003,-0.002,-13.633>,<-0.9999998,0.0001189,0.0006208>
            CONSTR/LINE,PRTO,CYL_B_INITIAL,POINT_C_INITIAL,45.36
            MOVE/POINT,NORMAL,<0,0,100>
            MOVE/POINT,NORMAL,<0,0,100>
ABC_INITIAL=ALIGNMENT/START,RECALL:ABSPH1ATEMP1,LIST=YES
              ALIGNMENT/LEVEL,ZPLUS,PLN_A_INITIAL
              ALIGNMENT/ROTATE,XMINUS,TO,LINE_C_INITIAL,ABOUT,YPLUS
              ALIGNMENT/BF2D,XPLUS,LEAST_SQR,CREATE WEIGHTS=NO,ROTONLY,USE SCALING=NO,0,0,0,0.008
              ITERATEANDREPIERCECAD=NO
              Deviation Threshold=0.1
              SHOWALLINPUTS=NO,SHOWALLPARAMS=NO
              ALIGNMENT/TRANS,XAXIS,CYL_B_INITIAL
              ALIGNMENT/TRANS,YAXIS,CYL_B_INITIAL
              ALIGNMENT/TRANS,ZAXIS,PLN_A_INITIAL
            ALIGNMENT/END
            TIP/T1A0B0, SHANKIJK=0.713, -0.071, 0.697, ANGLE=4.416
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<0,0,10>
PLN_A      =FEAT/CONTACT/PLANE/ADAPTIVE_PLANE_CIRCLE_SCAN,CARTESIAN,OUTLINE,LEAST_SQR
            THEO/<0,0,0>,<0,0,1>
            ACTL/<-0.482,-1.383,0>,<-0.0006194,0.0001414,0.9999998>
            TARG/<0,0,0>,<0,0,1>
            ANGLE VEC=<1,0,0>,RADIAL
            SHOW FEATURE PARAMETERS=YES
              VOID DETECTION=YES
              SURFACE=THICKNESS_NONE,0
              MEASURE MODE=NOMINALS
              RMEAS=NONE,NONE,NONE
              AUTO WRIST=NO
              CIRCULAR MOVES=CIRCULAR
              GRAPHICAL ANALYSIS=NO
              FEATURE LOCATOR=NO,NO,""
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=3007,NUMRINGS=2
              SPACER=33
              AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0,DISTANCE AFTER=0,DIRECTION=ALONG FEATURE VECTOR
              USE BOUNDARY OFFSET=NO
            SHOW HITS=NO
A          =ALIGNMENT/START,RECALL:ABC_INITIAL,LIST=YES
              ALIGNMENT/LEVEL,ZPLUS,PLN_A
              ALIGNMENT/TRANS,ZAXIS,PLN_A
            ALIGNMENT/END
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<0,0,10>
CYL_B      =FEAT/CONTACT/CYLINDER/ADAPTIVE_CYLINDER_SPIRAL_SCAN,CARTESIAN,IN,MAX_INSC
            THEO/<0,0,-18.7>,<0,0,1>,89.05,8.8
            ACTL/<-0.012,0.003,-18.7>,<0.0006206,-0.0003959,0.9999997>,89.08,8.8
            TARG/<0,0,-18.7>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<0.1021822,0.9947657,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=2912,NUMLEVELS=2,DEPTH=2,END OFFSET=1,PITCH=2.5
              SAMPLE METHOD=SAMPLE_HITS
              SAMPLE HITS=0,SPACER=0
              AVOIDANCE MOVE=NO
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=NO
AB         =ALIGNMENT/START,RECALL:A,LIST=YES
              ALIGNMENT/LEVEL,ZPLUS,PLN_A
              ALIGNMENT/TRANS,XAXIS,CYL_B
              ALIGNMENT/TRANS,YAXIS,CYL_B
              ALIGNMENT/TRANS,ZAXIS,PLN_A
            ALIGNMENT/END
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<50,0,50>
            MOVE/POINT,NORMAL,<50,0,50>
            TIP/T1A45B-90, SHANKIJK=1, 0.004, -0.009, ANGLE=-84.003
            MOVE/POINT,NORMAL,<0,0,10>
            MOVE/POINT,NORMAL,<0,0,10>
SPH_1A_TEMP2_C1=FEAT/CONTACT/SPHERE/DEFAULT,POLAR,IN,LEAST_SQR
            THEO/<41.6,180,-13.6>,<1,0,0>,14.8
            ACTL/<41.639,180.001,-13.596>,<1,0,0>,14.868
            TARG/<41.6,180,-13.6>,<1,0,0>
            START ANGLE 1=0,END ANG 1=360
            START ANGLE 2=-90,END ANG 2=-40
            ANGLE VEC=<-0.0086787,0,-0.9999623>
            SHOW FEATURE PARAMETERS=YES
              SURFACE=THICKNESS_NONE,0
              MEASURE MODE=NOMINALS
              RMEAS=NONE,NONE,NONE
              AUTO WRIST=NO
              GRAPHICAL ANALYSIS=NO
              FEATURE LOCATOR=NO,NO,""
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=11,NUMROWS=3
              AVOIDANCE MOVE=NO
            SHOW HITS=NO
ABSPH1ATEMP2=ALIGNMENT/START,RECALL:AB,LIST=YES
              ALIGNMENT/ROTATE_CIRCLE,XMINUS,TO,CYL_B,AND,SPH_1A_TEMP2_C1,ABOUT,ZPLUS
            ALIGNMENT/END
PNT_C1     =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
            THEO/<-45.36,-6.374,-13.6>,<0.5080827,0.8613083,0>
            ACTL/<-45.401,-6.432,-13.603>,<0.5080827,0.8613083,0>
            TARG/<-45.36,-6.374,-13.6>,<0.5080827,0.8613083,0>
            SNAP=NO
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=NO
LIN_C1     =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
            THEO/<0,0,-13.6>,<-0.9902718,-0.1391469,0>
            ACTL/<0.003,-0.002,-13.628>,<-0.9901217,-0.1402092,0.000559>
            CONSTR/LINE,PRTO,CYL_B,PNT_C1,45.805
PNT_C2     =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
            THEO/<-45.36,6.374,-13.6>,<0.5080827,-0.8613083,0>
            ACTL/<-45.403,6.439,-13.607>,<0.5080827,-0.8613083,0>
            TARG/<-45.36,6.374,-13.6>,<0.5080827,-0.8613083,0>
            SNAP=NO
            SHOW FEATURE PARAMETERS=NO
            SHOW CONTACT PARAMETERS=NO
LIN_C2     =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
            THEO/<0,0,-13.6>,<-0.9902718,0.1391469,0>
            ACTL/<0.003,-0.002,-13.637>,<-0.9900877,0.140449,0.0006701>
            CONSTR/LINE,PRTO,CYL_B,PNT_C2,45.805
POINT_C    =FEAT/POINT,CARTESIAN,NO
            THEO/<-45.36,0,-13.6>,<-0.0035286,0.9999938,0>
            ACTL/<-45.402,0.004,-13.605>,<0.0069724,0.999975,-0.0011576>
            CONSTR/POINT,MID,PNT_C1,PNT_C2
LINE_C     =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
            THEO/<0,0,-13.6>,<-1,0,0>
            ACTL/<0.003,-0.002,-13.633>,<-0.9999998,0.0001264,0.0006206>
            CONSTR/LINE,PRTO,CYL_B,POINT_C,45.36
POINT_ORIGIN=FEAT/POINT,CARTESIAN,NO
            THEO/<0,0,0>,<0,0,1>
            ACTL/<0.012,-0.007,0>,<0.0006206,-0.0003959,0.9999997>
            CONSTR/POINT,PIERCE,PLN_A,CYL_B
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.017,100>
            TIP/T1A45B45, SHANKIJK=0.095, 0.426, 0.9, ANGLE=64.678
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.004,10>
SPH_2A_C2  =FEAT/CONTACT/SPHERE/DEFAULT,POLAR,IN,LEAST_SQR
            THEO/<41.6,317,-13.6>,<-0.7313537,0.6819984,0>,14.8
            ACTL/<41.615,317.019,-13.595>,<-0.7313537,0.6819984,0>,14.899
            TARG/<41.6,317,-13.6>,<-0.7313537,0.6819984,0>
            START ANGLE 1=0,END ANG 1=360
            START ANGLE 2=-90,END ANG 2=-35
            ANGLE VEC=<0.6223044,0.6673398,-0.4091391>
            SHOW FEATURE PARAMETERS=YES
              SURFACE=THICKNESS_NONE,0
              MEASURE MODE=NOMINALS
              RMEAS=NONE,NONE,NONE
              AUTO WRIST=NO
              GRAPHICAL ANALYSIS=NO
              FEATURE LOCATOR=NO,NO,""
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=17,NUMROWS=3
              AVOIDANCE MOVE=NO
            SHOW HITS=NO
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.017,100>
            TIP/T1A45B150, SHANKIJK=-0.348, -0.616, 0.707, ANGLE=141.468
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.004,10>
SPH_3A_C3  =FEAT/CONTACT/SPHERE/DEFAULT,POLAR,IN,LEAST_SQR
            THEO/<41.6,60,-13.6>,<-0.5,-0.8660254,0>,14.8
            ACTL/<41.601,60.018,-13.6>,<-0.5,-0.8660254,0>,14.898
            TARG/<41.6,60,-13.6>,<-0.5,-0.8660254,0>
            START ANGLE 1=0,END ANG 1=360
            START ANGLE 2=-90,END ANG 2=-35
            ANGLE VEC=<0.6656096,-0.3842899,-0.639754>
            SHOW FEATURE PARAMETERS=YES
              SURFACE=THICKNESS_NONE,0
              MEASURE MODE=NOMINALS
              RMEAS=NONE,NONE,NONE
              AUTO WRIST=NO
              GRAPHICAL ANALYSIS=NO
              FEATURE LOCATOR=NO,NO,""
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=17,NUMROWS=3
              AVOIDANCE MOVE=NO
            SHOW HITS=NO
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.017,100>
            TIP/T1A45B-90, SHANKIJK=0.707, 0.009, 0.707, ANGLE=-89.528
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.017,100>
            MOVE/POINT,NORMAL,<0,0.004,10>
            MOVE/POINT,NORMAL,<0,0.004,10>
ABC        =ALIGNMENT/START,RECALL:ABSPH1ATEMP2,LIST=YES
              ALIGNMENT/LEVEL,ZPLUS,PLN_A
              ALIGNMENT/BF2D,ZPLUS,LEAST_SQR,CREATE WEIGHTS=NO,ROTONLY,USE SCALING=NO,0,0,0,0.013
              ITERATEANDREPIERCECAD=NO
              Deviation Threshold=0.1
              SHOWALLINPUTS=NO,SHOWALLPARAMS=NO
              ALIGNMENT/TRANS,XAXIS,CYL_B
              ALIGNMENT/TRANS,YAXIS,CYL_B
              ALIGNMENT/TRANS,ZAXIS,PLN_A
            ALIGNMENT/END
            DATDEF/A,FEATURES=PLN_A,,
            DATDEF/B,FEATURES=CYL_B,,
            DATDEF/C,FEATURES=SPH_1A_TEMP2_C1,SPH_2A_C2,SPH_3A_C3,,
GRP_1A     =GROUP/SHOWALLPARAMS=YES
SPH_1A       =FEAT/CONTACT/SPHERE/DEFAULT,POLAR,IN,LEAST_SQR
              THEO/<41.6,180,-13.6>,<1,0,0>,14.8
              ACTL/<41.641,179.987,-13.593>,<1,0,0>,14.859
              TARG/<41.6,180,-13.6>,<1,0,0>
              START ANGLE 1=0,END ANG 1=360
              START ANGLE 2=-90,END ANG 2=-40
              ANGLE VEC=<-0.0086787,0,-0.9999623>
              SHOW FEATURE PARAMETERS=YES
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=17,NUMROWS=3
                AVOIDANCE MOVE=NO
              SHOW HITS=NO
SCN_1A_NO    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_1A_LM    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_1A_PQ    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_1A_RS    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
            ENDGROUP/ID=GRP_1A
            MOVE/POINT,NORMAL,<0,0.005,10>
            MOVE/POINT,NORMAL,<0,0.005,10>
            MOVE/POINT,NORMAL,<0,0.021,100>
            MOVE/POINT,NORMAL,<0,0.021,100>
            TIP/T1A45B45, SHANKIJK=0.095, 0.426, 0.9, ANGLE=64.664
            MOVE/POINT,NORMAL,<0,0.021,100>
            MOVE/POINT,NORMAL,<0,0.021,100>
            MOVE/POINT,NORMAL,<0,0.005,10>
            MOVE/POINT,NORMAL,<0,0.005,10>
GRP_2A     =GROUP/SHOWALLPARAMS=YES
SPH_2A       =FEAT/CONTACT/SPHERE/DEFAULT,POLAR,IN,LEAST_SQR
              THEO/<41.6,317,-13.6>,<-0.7313537,0.6819984,0>,14.8
              ACTL/<41.615,317.007,-13.595>,<-0.7313537,0.6819984,0>,14.899
              TARG/<41.6,317,-13.6>,<-0.7313537,0.6819984,0>
              START ANGLE 1=0,END ANG 1=360
              START ANGLE 2=-90,END ANG 2=-35
              ANGLE VEC=<0.6223044,0.6673398,-0.4091391>
              SHOW FEATURE PARAMETERS=YES
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=17,NUMROWS=3
                AVOIDANCE MOVE=NO
              SHOW HITS=NO
LIN_SPH_2A   =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
              THEO/<0,0,-13.6>,<0.7313537,-0.6819984,0>
              ACTL/<0.003,-0.002,-13.565>,<0.7314253,-0.6819212,-0.000724>
              CONSTR/LINE,PRTO,CYL_B,SPH_2A,41.6
SCN_2A_NO    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_2A_LM    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_2A_PQ    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_2A_RS    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
            ENDGROUP/ID=GRP_2A
            MOVE/POINT,NORMAL,<0,0.005,10>
            MOVE/POINT,NORMAL,<0,0.005,10>
            MOVE/POINT,NORMAL,<0,0.021,100>
            MOVE/POINT,NORMAL,<0,0.021,100>
            TIP/T1A45B150, SHANKIJK=-0.348, -0.615, 0.707, ANGLE=141.455
            MOVE/POINT,NORMAL,<0,0.021,100>
            MOVE/POINT,NORMAL,<0,0.021,100>
            MOVE/POINT,NORMAL,<0,0.005,10>
            MOVE/POINT,NORMAL,<0,0.005,10>
GRP_3A     =GROUP/SHOWALLPARAMS=YES
SPH_3A       =FEAT/CONTACT/SPHERE/DEFAULT,POLAR,IN,LEAST_SQR
              THEO/<41.6,60,-13.6>,<-0.5,-0.8660254,0>,14.8
              ACTL/<41.601,60.006,-13.6>,<-0.5,-0.8660254,0>,14.899
              TARG/<41.6,60,-13.6>,<-0.5,-0.8660254,0>
              START ANGLE 1=0,END ANG 1=360
              START ANGLE 2=-90,END ANG 2=-35
              ANGLE VEC=<0.6656096,-0.3842899,-0.639754>
              SHOW FEATURE PARAMETERS=YES
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=17,NUMROWS=3
                AVOIDANCE MOVE=NO
              SHOW HITS=NO
LIN_SPH_3A   =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
              THEO/<0,0,-13.6>,<0.5,0.8660254,0>
              ACTL/<0.003,-0.002,-13.601>,<0.4998368,0.8661196,0.0000329>
              CONSTR/LINE,PRTO,CYL_B,SPH_3A,41.6
SCN_3A_NO    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_3A_LM    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_3A_PQ    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
SCN_3A_RS    =FEAT/SCAN,LINEAROPEN,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
              MEAS/SCAN
                BASICSCAN/LINE,NUMBER OF HITS=10,SHOW HITS=NO,SHOWALLPARAMS=NO
                ENDSCAN
              ENDMEAS/
            ENDGROUP/ID=GRP_3A
            MOVE/POINT,NORMAL,<0,0.005,10>
            MOVE/POINT,NORMAL,<0,0.005,10>
            MOVE/POINT,NORMAL,<0,0.021,100>
            MOVE/POINT,NORMAL,<0,0.021,100>
            TIP/T1A0B0, SHANKIJK=0.716, 0.027, 0.697, ANGLE=9.896
            MOVE/POINT,NORMAL,<0.066,200.021,99.964>
            MOVE/POINT,NORMAL,<0.066,200.021,99.964>
            COMMENT/REPT,
            **************** DATUM A  *********************
DIM 100= LOCATION OF PLANE PLN_A  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
Z        0.000      0.000      0.025      0.025      0.000      0.000 ---#----
END OF DIMENSION 100
            COMMENT/REPT,
            **************** DATUM B  *********************
DIM BALL_P3_220= LOCATION OF CYLINDER CYL_B  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
Z      -18.700    -18.700      0.025      0.025      0.000      0.000 ---#----
D       89.050     89.080      0.035      0.000      0.030      0.000 ------#-
L        8.800      8.800      0.025      0.025      0.000      0.000 ---#----
END OF DIMENSION BALL_P3_220
BALL_P3_CYLINDRICITY=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            FEATURE_MATH=DEFAULT,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,
            SEGMENT_1,CYLINDRICITY,0.035,TOL_ZONE_MATH=DEFAULT,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=10,
              MEASURED:
                CYL_B:0.010,
            FEATURES/CYL_B,,
            COMMENT/REPT,
            **************** DATUM C *********************
DIM BALL_C1= LOCATION OF POINT PNT_C1  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
X      -45.360    -45.403      0.025      0.025     -0.043      0.018 <-------
Z      -13.600    -13.603      0.025      0.025     -0.003      0.000 ---#----
END OF DIMENSION BALL_C1
DIM BALL_C2= LOCATION OF POINT PNT_C2  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
X      -45.360    -45.402      0.025      0.250     -0.042      0.000 ------#-
Z      -13.600    -13.607      0.025      0.025     -0.007      0.000 --#-----
END OF DIMENSION BALL_C2
            ASSIGN/V16=16
DIM BALL_C1_C2_REF= 2D ANGLE TO LINE LIN_C1 FROM LINE LIN_C2 SUPPLEMENTAL ANGLE=NO ,$
GRAPH=OFF  TEXT=OFF  MULT=200.00  OUTPUT=BOTH
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
A    V16     16.134      0.025      0.025      0.134      0.109 ------->
DIM BALL_C= LOCATION OF POINT POINT_C  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
X      -45.360    -45.402      0.025      0.250     -0.042      0.000 ------#-
Z      -13.600    -13.605      0.025      0.025     -0.005      0.000 ---#----
END OF DIMENSION BALL_C
DIM 300= LOCATION OF LINE LINE_C  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
Y        0.000      0.006      0.025      0.025      0.006      0.000 ----#---
END OF DIMENSION 300
            WORKPLANE/ZPLUS
            COMMENT/REPT,
            
            -----     PAGE 3     -----
            
            COMMENT/REPT,
            
            -----     CALOTTE 1A     -----
            
            RECALL/ALIGNMENT,INTERNAL,ABC
BALL_P3_1A_REF_2=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=200,
              MEASURED:
                SPH_1A:-0.037,-0.074,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SPH_1A,,
DIM BALL_P3_1A_REF_3= LOCATION OF SPHERE SPH_1A  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=200.00  ARROWDENSITY=100  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
Z      -13.600    -13.593      0.025      0.025      0.007      0.000 -----#--
PR      41.600     41.641      0.025      0.025      0.041      0.016 ------->
PA     180.000    179.987      0.025      0.025     -0.013      0.000 -#------
D       14.800     14.859      0.025      0.025      0.059      0.034 ------->
RN       0.000      0.032      0.025      0.000      0.032      0.007 ------->
END OF DIMENSION BALL_P3_1A_REF_3
BALL_P3_1A_REF4=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            FEATURE_MATH=DEFAULT,DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,
            SIZE/NOMINAL=14.8,TOLERANCE SPECIFICATION MODE=NOMINAL_WITH_DEVIATIONS,
            UPPER TOLERANCE=0.025,LOWER TOLERANCE=0.025,
              SPH_1A:
                MIN LOCAL SIZE:14.842,
                MAX LOCAL SIZE:14.880,
            SEGMENT_1,POSITION,SPHERICAL,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=200,
              MEASURED:
                SPH_1A:0.079,
            ADD
            DATUMS/REPORTDATUMSIZE=ON,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SPH_1A,,
BALL_P3_243=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_1A_LM:-0.068,-0.078,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_1A_LM,,
BALL_P3_246=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_1A_NO:-0.057,-0.070,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_1A_NO,,
BALL_P3_255=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_1A_PQ:-0.041,-0.068,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_1A_PQ,,
BALL_P3_258=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_1A_RS:-0.054,-0.061,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_1A_RS,,
            COMMENT/REPT,
            
            -----     CALOTTE 2A     -----
            
            RECALL/ALIGNMENT,INTERNAL,ABC
            ASSIGN/V137=137
BALL_P3_2A_REF_2=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=200,
              MEASURED:
                SPH_2A:-0.041,-0.081,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SPH_2A,,
DIM BALL_P3_2A_REF_3= LOCATION OF SPHERE SPH_2A  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=200.00  ARROWDENSITY=100  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
Z      -13.600    -13.595      0.025      0.025      0.005      0.000 ----#---
PR      41.600     41.615      0.025      0.025      0.015      0.000 ------#-
PA     317.000    317.007      0.025      0.025      0.007      0.000 -----#--
D       14.800     14.899      0.025      0.025      0.099      0.074 ------->
RN       0.000      0.031      0.025      0.000      0.031      0.006 ------->
END OF DIMENSION BALL_P3_2A_REF_3
BALL_P3_2A_REF_4=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            FEATURE_MATH=DEFAULT,DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,
            SIZE/NOMINAL=14.8,TOLERANCE SPECIFICATION MODE=NOMINAL_WITH_DEVIATIONS,
            UPPER TOLERANCE=0.025,LOWER TOLERANCE=0.025,
              SPH_2A:
                MIN LOCAL SIZE:14.881,
                MAX LOCAL SIZE:14.920,
            SEGMENT_1,POSITION,SPHERICAL,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=200,
              MEASURED:
                SPH_2A:0.040,
            ADD
            DATUMS/REPORTDATUMSIZE=ON,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SPH_2A,,
BALL_P3_244=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_2A_LM:-0.066,-0.079,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_2A_LM,,
BALL_P3_247=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_2A_NO:-0.066,-0.079,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_2A_NO,,
BALL_P3_256=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_2A_PQ:-0.035,-0.057,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_2A_PQ,,
BALL_P3_259=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_2A_RS:-0.051,-0.067,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_2A_RS,,
            COMMENT/REPT,
            
            -----     CALOTTE 3A     -----
            
            RECALL/ALIGNMENT,INTERNAL,ABC
BALL_P3_3A_REF_2=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=200,
              MEASURED:
                SPH_3A:-0.022,-0.070,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SPH_3A,,
DIM BALL_P3_3A_REF_3= LOCATION OF SPHERE SPH_3A  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=200.00  ARROWDENSITY=100  OUTPUT=BOTH  HALF ANGLE=NO
AX    NOMINAL       MEAS       +TOL       -TOL        DEV     OUTTOL
Z      -13.600    -13.600      0.025      0.025      0.000      0.000 ----#---
PR      41.600     41.601      0.025      0.025      0.001      0.000 ----#---
PA      60.000     60.006      0.025      0.025      0.006      0.000 ----#---
D       14.800     14.899      0.025      0.025      0.099      0.074 ------->
RN       0.000      0.035      0.000      0.000      0.035      0.035 ------->
END OF DIMENSION BALL_P3_3A_REF_3
BALL_P3_3A_REF4=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            FEATURE_MATH=DEFAULT,DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,
            SIZE/NOMINAL=14.8,TOLERANCE SPECIFICATION MODE=NOMINAL_WITH_DEVIATIONS,
            UPPER TOLERANCE=0.025,LOWER TOLERANCE=0.025,
              SPH_3A:
                MIN LOCAL SIZE:14.876,
                MAX LOCAL SIZE:14.924,
            SEGMENT_1,POSITION,SPHERICAL,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=200,
              MEASURED:
                SPH_3A:0.025,
            ADD
            DATUMS/REPORTDATUMSIZE=ON,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SPH_3A,,
BALL_P3_245=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_3A_LM:-0.053,-0.061,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_3A_LM,,
BALL_P3_248=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_3A_NO:-0.053,-0.066,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_3A_NO,,
BALL_P3_257=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=50,
              MEASURED:
                SCN_3A_PQ:-0.019,-0.042,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_3A_PQ,,
BALL_P3_260=GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
            DESCRIPTION=OFF,,
            DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF,
            UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDREPIERCECAD=YES,
            SEGMENT_1,PROFILE_SURFACE,0.05,__,A,B,__,__,C,__,__,
            TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=60,
              MEASURED:
                SCN_3A_RS:-0.042,-0.051,
            ADD
            DATUMS/REPORTDATUMSIZE=OFF,
              B(CYL_B):NOM=89.05,+Tol=0.035,-Tol=0,
              C(SPH_1A_TEMP2_C1):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_2A_C2):NOM=14.8,+Tol=0.025,-Tol=0.025,
              C(SPH_3A_C3):NOM=14.8,+Tol=0.025,-Tol=0.025,
            FEATURES/SCN_3A_RS,,