Hope everyone is well on this Friday. I have a decent issue on my hands. I'm measuring a few parts to get a feel for what the numbers are. The first part was a completed part that inspected all the features. The next two parts are missing a giant bore in them. But wanted to check the position of some other holes.
The problem I'm having is that, my report shows the same numbers as from the first part. Its not updating to the newly measured parts. Any idead to as what I'm doing wrong? Thaks for your time.
Dim item#1_a to b face= 2d distance from plane datum_a to plane b_face par to yaxis,no_radius units=in,$
graph=off text=off mult=10.00 output=both
ax nominal +tol -tol meas dev outtol
m 14.2150 0.0200 0.0200 14.1938 -0.0212 0.0012 <----
dim item#2_a to c face= 2d distance from plane datum_a to plane c_face par to yaxis,no_radius units=in,$
graph=off text=off mult=10.00 output=both
ax nominal +tol -tol meas dev outtol
m 10.0050 0.0150 0.0150 10.0057 0.0007 0.0000 --#--
dim item#3_datum_a flatness= flatness of plane datum_a units=in ,$
graph=off text=off mult=10.00 arrowdensity=100 output=both
ax nominal +tol -tol meas dev outtol
m 0.0000 0.0200 0.0000 0.0032 0.0032 0.0000 #----
dim item#4.1_position of cir1 to abc= position of circle cir1 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x 0.0000 0.0088 0.0088
z 0.0000 -0.0136 -0.0136
df 0.1562 0.0050 0.0050 0.0098 0.1610 0.0048 0.0000 ----#
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0141 0.0324 0.0324 0.0000 ----#
end of dimension item#4.1_position of cir1 to abc
dim item#4.2_position of cir3 to abc= position of circle cir3 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x -3.5894 -3.5806 0.0088
z -1.5270 -1.5334 -0.0064
df 0.1562 0.0050 0.0050 0.0097 0.1609 0.0047 0.0000 ----#
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0140 0.0217 0.0217 0.0000 ---#-
end of dimension item#4.2_position of cir3 to abc
dim item#4.3_position of cir5 to abc= position of circle cir5 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x -3.5894 -3.5830 0.0064
z -6.3390 -6.3441 -0.0051
df 0.1562 0.0050 0.0050 0.0100 0.1628 0.0066 0.0016 ---->
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0143 0.0163 0.0163 0.0000 --#--
end of dimension item#4.3_position of cir5 to abc
dim item#4.4_position of cir6 to abc= position of circle cir6 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x 0.0001 0.0004 0.0003
z -7.8670 -7.8855 -0.0185
df 0.1562 0.0050 0.0050 0.0100 0.1630 0.0068 0.0018 ---->
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0143 0.0370 0.0370 0.0027 ---->
end of dimension item#4.4_position of cir6 to abc
dim item#4.5_position of cir7 to abc= position of circle cir7 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x 3.5895 3.5855 -0.0040
z -6.3389 -6.3512 -0.0122
df 0.1562 0.0050 0.0050 0.0100 0.1617 0.0055 0.0005 ---->
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0143 0.0258 0.0258 0.0000 ---#-
end of dimension item#4.5_position of cir7 to abc
dim item#4.6_position of cir9 to abc= position of circle cir9 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x 3.5895 3.5990 0.0096
z -1.5269 -1.5429 -0.0159
df 0.1562 0.0050 0.0050 0.0091 0.1603 0.0041 0.0000 ----#
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0134 0.0371 0.0371 0.0037 ---->
Dim item#1_a to b face= 2d distance from plane datum_a to plane b_face par to yaxis,no_radius units=in,$
graph=off text=off mult=10.00 output=both
ax nominal +tol -tol meas dev outtol
m 14.2150 0.0200 0.0200 14.1938 -0.0212 0.0012 <----
dim item#2_a to c face= 2d distance from plane datum_a to plane c_face par to yaxis,no_radius units=in,$
graph=off text=off mult=10.00 output=both
ax nominal +tol -tol meas dev outtol
m 10.0050 0.0150 0.0150 10.0057 0.0007 0.0000 --#--
dim item#3_datum_a flatness= flatness of plane datum_a units=in ,$
graph=off text=off mult=10.00 arrowdensity=100 output=both
ax nominal +tol -tol meas dev outtol
m 0.0000 0.0200 0.0000 0.0032 0.0032 0.0000 #----
dim item#4.1_position of cir1 to abc= position of circle cir1 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x 0.0000 0.0088 0.0088
z 0.0000 -0.0136 -0.0136
df 0.1562 0.0050 0.0050 0.0098 0.1610 0.0048 0.0000 ----#
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0141 0.0324 0.0324 0.0000 ----#
end of dimension item#4.1_position of cir1 to abc
dim item#4.2_position of cir3 to abc= position of circle cir3 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x -3.5894 -3.5806 0.0088
z -1.5270 -1.5334 -0.0064
df 0.1562 0.0050 0.0050 0.0097 0.1609 0.0047 0.0000 ----#
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0140 0.0217 0.0217 0.0000 ---#-
end of dimension item#4.2_position of cir3 to abc
dim item#4.3_position of cir5 to abc= position of circle cir5 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x -3.5894 -3.5830 0.0064
z -6.3390 -6.3441 -0.0051
df 0.1562 0.0050 0.0050 0.0100 0.1628 0.0066 0.0016 ---->
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0143 0.0163 0.0163 0.0000 --#--
end of dimension item#4.3_position of cir5 to abc
dim item#4.4_position of cir6 to abc= position of circle cir6 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x 0.0001 0.0004 0.0003
z -7.8670 -7.8855 -0.0185
df 0.1562 0.0050 0.0050 0.0100 0.1630 0.0068 0.0018 ---->
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0143 0.0370 0.0370 0.0027 ---->
end of dimension item#4.4_position of cir6 to abc
dim item#4.5_position of cir7 to abc= position of circle cir7 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x 3.5895 3.5855 -0.0040
z -6.3389 -6.3512 -0.0122
df 0.1562 0.0050 0.0050 0.0100 0.1617 0.0055 0.0005 ---->
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0143 0.0258 0.0258 0.0000 ---#-
end of dimension item#4.5_position of cir7 to abc
dim item#4.6_position of cir9 to abc= position of circle cir9 units=in ,$
graph=off text=off mult=10.00 output=both fit to datums=off dev perpen centerline=off display=diameter
ax nominal +tol -tol bonus meas dev outtol
x 3.5895 3.5990 0.0096
z -1.5269 -1.5429 -0.0159
df 0.1562 0.0050 0.0050 0.0091 0.1603 0.0041 0.0000 ----#
d1 plane datum_a at rfs
d2 1.2800 0.0050 0.0050 0.0043 1.2793 circle datum_b at mmc
d3 0.3850 0.0050 0.0050 0.0055 0.3855 circle datum_c at mmc
tp mmc 0.0200 0.0134 0.0371 0.0371 0.0037 ---->