Having to F9 every point for program to run

Hello all,

I have come across an issue I have never seen before. I picked up my tooling balls and start running the full layout. The surface points run just fine but when it gets to the trim + Hole features the program faults out.

I then have to F9 every point or right click on the feature and go into Feature -- > Reset measured values to nominal for the points to run.

Is there a setting that I have off for the program to behave this way? Once I run through the program once it runs fine.

I feel like it's something so simple causing this but can't figure out why.

Parents

Smasherofprobes over 1 year ago

trim-104   =feat/contact/edge point/default,cartesian
            theo/<3525,761.031,1652.786>,<-0.0547968,-0.2485597,0.9670653>,<-0.0029022,0.9685561,0.2487784>
            actl/<3524.995,760.658,1652.817>,<-0.0547968,-0.2485597,0.9670654>,<-0.0029022,0.9685561,0.2487784>
            targ/<3525,761.031,1652.786>,<-0.0547968,-0.2485597,0.9670653>,<-0.0029022,0.9685561,0.2487784>
            measure order=surface
            show feature parameters=yes
              void detection=yes
              surface1=actl_thickness,0
              surface2=actl_thickness,0
              measure mode=nominals
              rmeas=none,none,none
              auto wrist=no
              graphical analysis=no
              feature locator=no,no,""
            show contact parameters=yes
              depth=0.5
              sample hits=1,spacer=2,indent1=1.5
              avoidance move=after,distance after=6,direction=along feature vector
              onerror=no
dim loc294= location of point trim-104  units=mm ,$
graph=off  text=off  mult=10.00  output=both  half angle=no
ax    nominal       meas       +tol       -tol        dev     outtol
x     3525.000   3524.995      0.500      0.500     -0.005      0.000 ----#----
y      761.031    760.658      0.500      0.500     -0.373      0.000 -#-------
z     1652.786   1652.817      0.500      0.500      0.032      0.000 ----#----
t        0.000      0.123      0.500      0.500      0.123      0.000 -----#---
end of dimension loc294
trim-105   =feat/contact/edge point/default,cartesian
            theo/<3440,761.888,1648.215>,<-0.0542465,-0.2465855,0.9676016>,<-0.0042229,0.9690765,0.2467245>
            actl/<3440,761.682,1648.202>,<-0.0542465,-0.2465854,0.9676017>,<-0.0042229,0.9690765,0.2467245>
            targ/<3440,761.888,1648.215>,<-0.0542465,-0.2465855,0.9676016>,<-0.0042229,0.9690765,0.2467245>
            measure order=surface
            show feature parameters=yes
              void detection=yes
              surface1=actl_thickness,0
              surface2=actl_thickness,0
              measure mode=nominals
              rmeas=none,none,none
              auto wrist=no
              graphical analysis=no
              feature locator=no,no,""
            show contact parameters=yes
              depth=0.5
              sample hits=1,spacer=2,indent1=1.5
              avoidance move=after,distance after=6,direction=along feature vector
              onerror=no
dim loc295= location of point trim-105  units=mm ,$
graph=off  text=off  mult=10.00  output=both  half angle=no
ax    nominal       meas       +tol       -tol        dev     outtol
x     3440.000   3440.000      0.500      0.500      0.000      0.000 ----#----
y      761.888    761.682      0.500      0.500     -0.205      0.000 --#------
z     1648.215   1648.202      0.500      0.500     -0.013      0.000 ----#----
t        0.000      0.038      0.500      0.500      0.038      0.000 ----#----
end of dimension loc295
            comment/rept,
            ***************************************
            attach applique boundry - marked 'z'
            ***************************************
            move/point,normal,<3439.715,886.8,1654.158>
            tip/t1a15b165, shankijk=0.25, 0.966, 0.067, angle=179.991
sqs-1      =feat/contact/square slot/default,cartesian,in
            theo/<3390.129,745.422,1696.353>,<0.4939395,0.8434699,0.211145>,<0.0736623,-0.2825562,0.9564182>,8.8,8.8
            actl/<3390.129,745.379,1697.232>,<0.4957608,0.8420132,0.2126854>,<0.0713958,-0.283586,0.9562853>,8.862,8.881
            targ/<3390.129,745.422,1696.353>,<0.4939395,0.8434699,0.211145>,<0.0736623,-0.2825562,0.9564182>
            meas width=yes,radius=2.5
            show feature parameters=yes
              remeasure=no
              surface=theo_thickness,0
              measure mode=nominals
              rmeas=none,none,none
              auto wrist=no
              graphical analysis=no
              feature locator=no,no,""
            show contact parameters=yes
              depth=0.5
              sample method=sample_hits
              sample hits=3,spacer=1.5
              avoidance move=both,distance before=5,distance after=5,direction=along feature vector
              find hole=disabled,onerror=no,read pos=no
            show hits=yes
              hit/basic,<3393.554,743.527,1693.543>,<-0.8663704,0.4568593,0.2016976>,<3393.517,743.709,1693.6>
              hit/basic,<3393.834,742.453,1697.177>,<-0.8663704,0.4568593,0.2016976>,<3393.796,742.632,1697.232>
              hit/basic,<3389.558,746.244,1692.039>,<0.0736623,-0.2825562,0.9564182>,<3389.556,746.22,1692.881>
              hit/basic,<3386.21,746.474,1698.952>,<0.8663704,-0.4568593,-0.2016976>,<3386.118,746.692,1699.026>
              hit/basic,<3385.93,747.548,1695.318>,<0.8663704,-0.4568593,-0.2016976>,<3385.852,747.765,1695.388>
              hit/basic,<3390.206,743.757,1700.456>,<-0.0736623,0.2825562,-0.9564182>,<3390.207,743.699,1701.372>
            endmeas/
dim loc296= location of slot sqs-1  units=mm ,$
graph=off  text=off  mult=10.00  output=both  half angle=no
ax    nominal       meas       +tol       -tol        dev     outtol
x     3390.129   3390.129      0.500      0.500      0.000      0.000 ----#----
y      745.422    745.379      0.500      0.500     -0.044      0.000 ----#----
z     1696.353   1697.232      0.500      0.500      0.879      0.379 -------->
d        8.800      8.862      0.100      0.100      0.062      0.000 -------#-
l        8.800      8.881      0.100      0.100      0.081      0.000 --------#
end of dimension loc296
dim loc326= position of slot sqs-1  units=mm ,$
graph=off  text=off  mult=10.00  output=both  fit to datums=off  dev perpen centerline=off  display=diameter
ax    nominal       meas       +tol       -tol      bonus        dev     outtol
x    3390.129   3390.129                                       0.000          
y     745.422    745.379                                      -0.044          
z    1696.353   1697.232                                       0.879          
lf      8.800      8.881      0.100      0.100      0.168      0.081      0.000 --------#
wf      8.800      8.862      0.100      0.100      0.149      0.062      0.000 -------#-
tp        mmc      1.760      1.000                 0.149      1.760      0.611 -------->
end of dimension loc326
sqs-2      =feat/contact/square slot/default,cartesian,in
            theo/<3409.013,656.849,1931.843>,<0.4935269,0.8060127,0.3267639>,<0.0745077,-0.4135077,0.907447>,8.8,8.804
            actl/<3409.353,656.242,1932.581>,<0.4923164,0.807518,0.324868>,<0.0662734,-0.4069256,0.911054>,8.846,8.861
            targ/<3409.013,656.849,1931.843>,<0.4935269,0.8060127,0.3267639>,<0.0745077,-0.4135077,0.907447>
            meas width=yes,radius=2.5
            show feature parameters=yes
              remeasure=no
              surface=theo_thickness,0
              measure mode=nominals
              rmeas=none,none,none
              auto wrist=no
              graphical analysis=no
              feature locator=no,no,""
            show contact parameters=yes
              depth=0.5
              sample method=sample_hits
              sample hits=3,spacer=1.5
              avoidance move=both,distance before=5,distance after=5,direction=along feature vector
              find hole=disabled,onerror=no,read pos=no
            show hits=yes
              hit/basic,<3412.438,655.369,1928.791>,<-0.8665332,0.4235031,0.2641313>,<3412.754,655.125,1928.656>
              hit/basic,<3412.721,653.796,1932.243>,<-0.8665332,0.4235031,0.2641313>,<3413.006,653.582,1932.122>
              hit/basic,<3408.439,658.266,1927.685>,<0.0745077,-0.4135077,0.907447>,<3408.805,657.647,1928.386>
              hit/basic,<3405.096,657.523,1934.568>,<0.8665332,-0.4235031,-0.2641313>,<3405.334,657.334,1934.422>
              hit/basic,<3404.812,659.096,1931.116>,<0.8665332,-0.4235031,-0.2641313>,<3405.079,658.88,1930.957>
              hit/basic,<3409.095,654.626,1935.674>,<-0.0745077,0.4135077,-0.907447>,<3409.407,654.028,1936.451>
            endmeas/
dim loc297= location of slot sqs-2  units=mm ,$
graph=off  text=off  mult=10.00  output=both  half angle=no
ax    nominal       meas       +tol       -tol        dev     outtol
x     3409.013   3409.353      0.500      0.500      0.340      0.000 -------#-
y      656.849    656.242      0.500      0.500     -0.607      0.107 <--------
z     1931.843   1932.581      0.500      0.500      0.738      0.238 -------->
d        8.800      8.846      0.100      0.100      0.046      0.000 ------#--
l        8.804      8.861      0.100      0.100      0.057      0.000 -------#-
end of dimension loc297
dim loc327= position of slot sqs-2  units=mm ,$
graph=off  text=off  mult=10.00  output=both  fit to datums=off  dev perpen centerline=off  display=diameter
ax    nominal       meas       +tol       -tol      bonus        dev     outtol
x    3409.013   3409.353                                       0.340          
y     656.849    656.242                                      -0.607          
z    1931.843   1932.581                                       0.738          
lf      8.804      8.861      0.100      0.100      0.062      0.057      0.000 -------#-
wf      8.800      8.846      0.100      0.100      0.052      0.046      0.000 ------#--
tp        mmc      2.029      1.000                 0.052      2.029      0.977 -------->
end of dimension loc327

Reply

Smasherofprobes over 1 year ago

trim-104   =feat/contact/edge point/default,cartesian
            theo/<3525,761.031,1652.786>,<-0.0547968,-0.2485597,0.9670653>,<-0.0029022,0.9685561,0.2487784>
            actl/<3524.995,760.658,1652.817>,<-0.0547968,-0.2485597,0.9670654>,<-0.0029022,0.9685561,0.2487784>
            targ/<3525,761.031,1652.786>,<-0.0547968,-0.2485597,0.9670653>,<-0.0029022,0.9685561,0.2487784>
            measure order=surface
            show feature parameters=yes
              void detection=yes
              surface1=actl_thickness,0
              surface2=actl_thickness,0
              measure mode=nominals
              rmeas=none,none,none
              auto wrist=no
              graphical analysis=no
              feature locator=no,no,""
            show contact parameters=yes
              depth=0.5
              sample hits=1,spacer=2,indent1=1.5
              avoidance move=after,distance after=6,direction=along feature vector
              onerror=no
dim loc294= location of point trim-104  units=mm ,$
graph=off  text=off  mult=10.00  output=both  half angle=no
ax    nominal       meas       +tol       -tol        dev     outtol
x     3525.000   3524.995      0.500      0.500     -0.005      0.000 ----#----
y      761.031    760.658      0.500      0.500     -0.373      0.000 -#-------
z     1652.786   1652.817      0.500      0.500      0.032      0.000 ----#----
t        0.000      0.123      0.500      0.500      0.123      0.000 -----#---
end of dimension loc294
trim-105   =feat/contact/edge point/default,cartesian
            theo/<3440,761.888,1648.215>,<-0.0542465,-0.2465855,0.9676016>,<-0.0042229,0.9690765,0.2467245>
            actl/<3440,761.682,1648.202>,<-0.0542465,-0.2465854,0.9676017>,<-0.0042229,0.9690765,0.2467245>
            targ/<3440,761.888,1648.215>,<-0.0542465,-0.2465855,0.9676016>,<-0.0042229,0.9690765,0.2467245>
            measure order=surface
            show feature parameters=yes
              void detection=yes
              surface1=actl_thickness,0
              surface2=actl_thickness,0
              measure mode=nominals
              rmeas=none,none,none
              auto wrist=no
              graphical analysis=no
              feature locator=no,no,""
            show contact parameters=yes
              depth=0.5
              sample hits=1,spacer=2,indent1=1.5
              avoidance move=after,distance after=6,direction=along feature vector
              onerror=no
dim loc295= location of point trim-105  units=mm ,$
graph=off  text=off  mult=10.00  output=both  half angle=no
ax    nominal       meas       +tol       -tol        dev     outtol
x     3440.000   3440.000      0.500      0.500      0.000      0.000 ----#----
y      761.888    761.682      0.500      0.500     -0.205      0.000 --#------
z     1648.215   1648.202      0.500      0.500     -0.013      0.000 ----#----
t        0.000      0.038      0.500      0.500      0.038      0.000 ----#----
end of dimension loc295
            comment/rept,
            ***************************************
            attach applique boundry - marked 'z'
            ***************************************
            move/point,normal,<3439.715,886.8,1654.158>
            tip/t1a15b165, shankijk=0.25, 0.966, 0.067, angle=179.991
sqs-1      =feat/contact/square slot/default,cartesian,in
            theo/<3390.129,745.422,1696.353>,<0.4939395,0.8434699,0.211145>,<0.0736623,-0.2825562,0.9564182>,8.8,8.8
            actl/<3390.129,745.379,1697.232>,<0.4957608,0.8420132,0.2126854>,<0.0713958,-0.283586,0.9562853>,8.862,8.881
            targ/<3390.129,745.422,1696.353>,<0.4939395,0.8434699,0.211145>,<0.0736623,-0.2825562,0.9564182>
            meas width=yes,radius=2.5
            show feature parameters=yes
              remeasure=no
              surface=theo_thickness,0
              measure mode=nominals
              rmeas=none,none,none
              auto wrist=no
              graphical analysis=no
              feature locator=no,no,""
            show contact parameters=yes
              depth=0.5
              sample method=sample_hits
              sample hits=3,spacer=1.5
              avoidance move=both,distance before=5,distance after=5,direction=along feature vector
              find hole=disabled,onerror=no,read pos=no
            show hits=yes
              hit/basic,<3393.554,743.527,1693.543>,<-0.8663704,0.4568593,0.2016976>,<3393.517,743.709,1693.6>
              hit/basic,<3393.834,742.453,1697.177>,<-0.8663704,0.4568593,0.2016976>,<3393.796,742.632,1697.232>
              hit/basic,<3389.558,746.244,1692.039>,<0.0736623,-0.2825562,0.9564182>,<3389.556,746.22,1692.881>
              hit/basic,<3386.21,746.474,1698.952>,<0.8663704,-0.4568593,-0.2016976>,<3386.118,746.692,1699.026>
              hit/basic,<3385.93,747.548,1695.318>,<0.8663704,-0.4568593,-0.2016976>,<3385.852,747.765,1695.388>
              hit/basic,<3390.206,743.757,1700.456>,<-0.0736623,0.2825562,-0.9564182>,<3390.207,743.699,1701.372>
            endmeas/
dim loc296= location of slot sqs-1  units=mm ,$
graph=off  text=off  mult=10.00  output=both  half angle=no
ax    nominal       meas       +tol       -tol        dev     outtol
x     3390.129   3390.129      0.500      0.500      0.000      0.000 ----#----
y      745.422    745.379      0.500      0.500     -0.044      0.000 ----#----
z     1696.353   1697.232      0.500      0.500      0.879      0.379 -------->
d        8.800      8.862      0.100      0.100      0.062      0.000 -------#-
l        8.800      8.881      0.100      0.100      0.081      0.000 --------#
end of dimension loc296
dim loc326= position of slot sqs-1  units=mm ,$
graph=off  text=off  mult=10.00  output=both  fit to datums=off  dev perpen centerline=off  display=diameter
ax    nominal       meas       +tol       -tol      bonus        dev     outtol
x    3390.129   3390.129                                       0.000          
y     745.422    745.379                                      -0.044          
z    1696.353   1697.232                                       0.879          
lf      8.800      8.881      0.100      0.100      0.168      0.081      0.000 --------#
wf      8.800      8.862      0.100      0.100      0.149      0.062      0.000 -------#-
tp        mmc      1.760      1.000                 0.149      1.760      0.611 -------->
end of dimension loc326
sqs-2      =feat/contact/square slot/default,cartesian,in
            theo/<3409.013,656.849,1931.843>,<0.4935269,0.8060127,0.3267639>,<0.0745077,-0.4135077,0.907447>,8.8,8.804
            actl/<3409.353,656.242,1932.581>,<0.4923164,0.807518,0.324868>,<0.0662734,-0.4069256,0.911054>,8.846,8.861
            targ/<3409.013,656.849,1931.843>,<0.4935269,0.8060127,0.3267639>,<0.0745077,-0.4135077,0.907447>
            meas width=yes,radius=2.5
            show feature parameters=yes
              remeasure=no
              surface=theo_thickness,0
              measure mode=nominals
              rmeas=none,none,none
              auto wrist=no
              graphical analysis=no
              feature locator=no,no,""
            show contact parameters=yes
              depth=0.5
              sample method=sample_hits
              sample hits=3,spacer=1.5
              avoidance move=both,distance before=5,distance after=5,direction=along feature vector
              find hole=disabled,onerror=no,read pos=no
            show hits=yes
              hit/basic,<3412.438,655.369,1928.791>,<-0.8665332,0.4235031,0.2641313>,<3412.754,655.125,1928.656>
              hit/basic,<3412.721,653.796,1932.243>,<-0.8665332,0.4235031,0.2641313>,<3413.006,653.582,1932.122>
              hit/basic,<3408.439,658.266,1927.685>,<0.0745077,-0.4135077,0.907447>,<3408.805,657.647,1928.386>
              hit/basic,<3405.096,657.523,1934.568>,<0.8665332,-0.4235031,-0.2641313>,<3405.334,657.334,1934.422>
              hit/basic,<3404.812,659.096,1931.116>,<0.8665332,-0.4235031,-0.2641313>,<3405.079,658.88,1930.957>
              hit/basic,<3409.095,654.626,1935.674>,<-0.0745077,0.4135077,-0.907447>,<3409.407,654.028,1936.451>
            endmeas/
dim loc297= location of slot sqs-2  units=mm ,$
graph=off  text=off  mult=10.00  output=both  half angle=no
ax    nominal       meas       +tol       -tol        dev     outtol
x     3409.013   3409.353      0.500      0.500      0.340      0.000 -------#-
y      656.849    656.242      0.500      0.500     -0.607      0.107 <--------
z     1931.843   1932.581      0.500      0.500      0.738      0.238 -------->
d        8.800      8.846      0.100      0.100      0.046      0.000 ------#--
l        8.804      8.861      0.100      0.100      0.057      0.000 -------#-
end of dimension loc297
dim loc327= position of slot sqs-2  units=mm ,$
graph=off  text=off  mult=10.00  output=both  fit to datums=off  dev perpen centerline=off  display=diameter
ax    nominal       meas       +tol       -tol      bonus        dev     outtol
x    3409.013   3409.353                                       0.340          
y     656.849    656.242                                      -0.607          
z    1931.843   1932.581                                       0.738          
lf      8.804      8.861      0.100      0.100      0.062      0.057      0.000 -------#-
wf      8.800      8.846      0.100      0.100      0.052      0.046      0.000 ------#--
tp        mmc      2.029      1.000                 0.052      2.029      0.977 -------->
end of dimension loc327

Children

WilliamL over 1 year ago in reply to Smasherofprobes

Do all your other features also have Void Detection on like Trim-104?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel