Program keeps prompting to save an excel form. I was playing around with this option a couple days ago and now it seems to be doing this on all the programs when the operators are running them. I've tried remaking the print command but that did not seem to work.
Why does it keep prompting for an excel form to save at the end even though I have it turned off?
Full code posted below, callout for this print command is at the very end
Thanks in advance
PROGRAM_SETUP=GROUP/SHOWALLPARAMS=YES
$$ NO,
path location to get the script for the dialog box at the begining of the part program....
FPTR =FILE/OPEN,C:\CMM\DIALOGBOXSCRIPTPATH.TXT,READ
V1 =FILE/READLINE,FPTR,{DialogBoxScript_line}
FILE/CLOSE,FPTR,KEEP
CS1 =SCRIPT/FILENAME= DIALOGBOXSCRIPT_LINE
FUNCTION/Main,SHOW=YES,,
STARTSCRIPT/
ENDSCRIPT/
$$ NO,
dialogbox script will assign variables to the following, these are dummy variables now - change nothing here ....
ASSIGN/CUST="SK Siltron"
ASSIGN/WO="7906698ap"
ASSIGN/SERIAL="SGL24023306"
ASSIGN/INSP="Kaleigh Hasselman"
ASSIGN/COMMENT=""
ASSIGN/PROCESS="After Purification"
ASSIGN/CAL_TYPE="Yes"
$$ NO,
$$ NO,
path location to get CMM ID #, from text file, on C drive of each machine.......
FPTR =FILE/OPEN,C:\CMM\MACHINE_ID.TXT,READ
V2 =FILE/READLINE,FPTR,{CMM_Name}
FILE/CLOSE,FPTR,KEEP
$$ NO,
$$ NO,
path to the location to save the finished cmm report .....
ASSIGN/STATC=GETPROGRAMINFO("SEQNUM")
FPTR =FILE/OPEN,C:\CMM\CMMREPORTPATH.TXT,READ
V3 =FILE/READLINE,FPTR,{CMM_Reportline}
FILE/CLOSE,FPTR,KEEP
ASSIGN/REPORT_PATH=CMM_REPORTLINE+"/"+MAT_NUMBER
ASSIGN/REPORT_NAME=REPORT_PATH+"/"+STATC+"_"+MAT_NUMBER+"_"+WO+"_"+SERIAL.PDF
$$ NO,
$$ NO,
path for the report file folder, to be used as a variable in the next script,to save under the material number.....
ASSIGN/RFOLDER=CMM_REPORTLINE+"/"+MAT_NUMBER
$$ NO,
$$ NO,
path for the location of the script, that creates the part number folder....
FPTR =FILE/OPEN,C:\CMM\PARTNUMBERFOLDERPATH.TXT,READ
V4 =FILE/READLINE,FPTR,{PartNumberScript_line}
FILE/CLOSE,FPTR,KEEP
RSCRIPT =SCRIPT/FILENAME= PARTNUMBERSCRIPT_LINE
FUNCTION/Main,SHOW=YES,,
STARTSCRIPT/
ENDSCRIPT/
$$ NO,
$$ NO,
path to the location to save the finished data file......
FPTR =FILE/OPEN,C:\CMM\CMMDATAPATH.TXT,READ
V5 =FILE/READLINE,FPTR,{CMM_Dataline}
FILE/CLOSE,FPTR,KEEP
ASSIGN/REPORT_NAME_2=CMM_DATALINE+"/"+MAT_NUMBER+"_"+WO+"_"+SERIAL.CSV
$$ NO,
$$ NO,
path to create customer name folder and work order folder (inside the pcdmis_data folder) to be used as a variable .....
FPTR =FILE/OPEN,C:\CMM\CMMDATAPATH2.TXT,READ
V6 =FILE/READLINE,FPTR,{Cmm_Dataline2}
FILE/CLOSE,FPTR,KEEP
ASSIGN/FOLDER_PATH=CMM_DATALINE2+"/"+CUST
ASSIGN/WO_PATH=FOLDER_PATH+"/"+WO
$$ NO,
$$ NO,
path to the location of the script that creates a customer name folder and work order number folder ......
FPTR =FILE/OPEN,C:\CMM\CUSTOMERNAMESCRIPTPATH.TXT,READ
V7 =FILE/READLINE,FPTR,{CustomerName_line}
FILE/CLOSE,FPTR,KEEP
CS2 =SCRIPT/FILENAME= CUSTOMERNAME_LINE
FUNCTION/Main,SHOW=YES,,
STARTSCRIPT/
ENDSCRIPT/
$$ NO,
$$ NO,
turns on the stats mode, sets the pointer and tracefields for the data file .....
STATS/ON,DES,DIRECTORY=WO_PATH
TRACEFIELD/DISPLAY=NO,REPORT=NO,DISPLAY MESSAGE=Customer ; Customer : CUST
TRACEFIELD/DISPLAY=NO,REPORT=NO,DISPLAY MESSAGE=Serial Number ; Serial Number : SERIAL
TRACEFIELD/DISPLAY=NO,REPORT=NO,DISPLAY MESSAGE=Work Order Number ; Work Order Number : WO
TRACEFIELD/DISPLAY=NO,REPORT=NO,DISPLAY MESSAGE=Inspector Name ; Inspector Name : INSP
TRACEFIELD/DISPLAY=NO,REPORT=NO,DISPLAY MESSAGE=Part Description ; Part Description : DESCRIP
TRACEFIELD/DISPLAY=NO,REPORT=NO,DISPLAY MESSAGE=Machining Part Drawing ; Machining Part Drawing : MACH_DRAWING
TRACEFIELD/DISPLAY=NO,REPORT=NO,DISPLAY MESSAGE=Finished Part Drawing ; Finished Part Drawing : FIN_DRAWING
TRACEFIELD/DISPLAY=NO,REPORT=NO,DISPLAY MESSAGE=Cmm Machine ; Cmm Machine : CMM_NAME
$$ NO,
$$ NO,
Program starts here .............
PROGRAM_START =LABEL/
COMMENT/REPT,
"Ship to Customer:" + CUST
"Material/Part Number:" + MAT_NUMBER
"Description:" +DESCRIP
"Uncoated/Machining Drawing:" + MACH_DRAWING
"Finished/Customer Drawing:" + FIN_DRAWING
"Work Order Number:" + WO
"Serial Number:" + SERIAL
" "
"Inspector Name:" + INSP
"Process Stage:"+ PROCESS
"Machine:" + CMM_NAME
"Special Comments:" +COMMENT
" "
IS THE PART ACCEPTABLE?(INITIAL,DATE, ADD COMMENTS)( YES / NO ) ____________________
" "
ENDGROUP/ID=PROGRAM_SETUP
$$ NO,
COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
Place part on table with Vblock in the +Y
Cbore in the +Z wth S/N in the +Y
Center probe over center of part
Press okay to continue
GRP1 =GROUP/SHOWALLPARAMS=YES
CHECK/2,1
PREHIT/0.25
RETRACT/0.25
MOVESPEED/ 100
TOUCHSPEED/ 2
READPOINT =FEAT/POINT,CARTESIAN
THEO/<0,0,0>,<0,0,1>
ACTL/<12.8334,10.659,-20.1784>,<0,0,1>
READPOINT/
ALIGNPLN =FEAT/PLANE,CARTESIAN,TRIANGLE,NO
THEO/<0,0,0>,<0,0,1>
ACTL/<0,0,0>,<0,0,1>
CONSTR/PLANE,ALIGN,ZPLUS
ALIGNLINE =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
THEO/<-0.5,0,0>,<1,0,0>
ACTL/<-0.5,0,0>,<1,0,0>
CONSTR/LINE,ALIGN,1,XPLUS
A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,ALIGNPLN
ALIGNMENT/TRANS,XAXIS,READPOINT
ALIGNMENT/TRANS,YAXIS,READPOINT
ALIGNMENT/TRANS,ZAXIS,READPOINT
ALIGNMENT/ROTATE,XPLUS,TO,ALIGNLINE,ABOUT,ZPLUS
ALIGNMENT/END
MODE/DCC
CLEARP/ZPLUS,0.5,ZPLUS,0,ON
MOVE/CLEARPLANE
PLN1 =FEAT/CONTACT/PLANE/DEFAULT,POLAR,NONE,LEAST_SQR
THEO/<0,0,0>,<0,0,1>
ACTL/<0.0002,319.2956,-0.5365>,<-0.000014,-0.0005313,0.9999999>
TARG/<0,0,0>,<0,0,1>
ANGLE VEC=<1,0,0>,RADIAL
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=3,NUMROWS=1
SPACER=3
AVOIDANCE MOVE=NO
SHOW HITS=YES
HIT/BASIC,<3,0,0>,<0,0,1>,<3.0002,359.9952,-0.5364>
HIT/BASIC,<3,120,0>,<0,0,1>,<3,119.996,-0.5351>
HIT/BASIC,<3,240,0>,<0,0,1>,<3.0001,240.0012,-0.5379>
ENDMEAS/
A2 =ALIGNMENT/START,RECALL:A1,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/TRANS,XAXIS,READPOINT
ALIGNMENT/TRANS,YAXIS,READPOINT
ALIGNMENT/ROTATE,XPLUS,TO,ALIGNLINE,ABOUT,ZPLUS
ALIGNMENT/END
MOVE/CLEARPLANE
MANID =FEAT/CONTACT/CIRCLE/DEFAULT,POLAR,IN,LEAST_SQR
THEO/<0,180,0>,<0,0,1>,4.8819
ACTL/<0.0002,333.5443,0>,<0,0,1>,4.8784
TARG/<0,180,0>,<0,0,1>
START ANG=240,END ANG=240
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=3,DEPTH=0.05,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=YES
HIT/BASIC,<2.441,240,-0.05>,<0.5,0.8660254,0>,<2.4392,240.0232,-0.05>
HIT/BASIC,<2.4409,0,-0.05>,<-1,0,0>,<2.4393,359.9974,-0.0495>
HIT/BASIC,<2.441,120,-0.05>,<0.5,-0.8660254,0>,<2.4391,119.9793,-0.0496>
ENDMEAS/
A3 =ALIGNMENT/START,RECALL:A2,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/TRANS,XAXIS,MANID
ALIGNMENT/TRANS,YAXIS,MANID
ALIGNMENT/ROTATE,XPLUS,TO,ALIGNLINE,ABOUT,ZPLUS
ALIGNMENT/END
PREHIT/0.1
RETRACT/0.1
CLEARP/ZPLUS,0.1,ZPLUS,0,ON
MOVE/CLEARPLANE
TOPPLN =FEAT/CONTACT/PLANE/DEFAULT,POLAR,NONE,LEAST_SQR
THEO/<0,0,0.0393>,<0,0,1>
ACTL/<0.0002,342.5966,0.036>,<0.0001868,0.0001404,1>
TARG/<0,0,0.0393>,<0,0,1>
ANGLE VEC=<COS(DEG2RAD(120)),SIN(DEG2RAD(120)),0>,RADIAL
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=6,NUMROWS=1
SPACER=(7.853+8.719)/4
AVOIDANCE MOVE=NO
SHOW HITS=YES
HIT/BASIC,<4.143,120,0.0393>,<0,0,1>,<4.143,119.9983,0.0357>
HIT/BASIC,<4.143,180,0.0393>,<0,0,1>,<4.1428,180.0009,0.0369>
HIT/BASIC,<4.143,240,0.0393>,<0,0,1>,<4.1431,240.0029,0.0366>
HIT/BASIC,<4.143,300,0.0393>,<0,0,1>,<4.1432,300.0004,0.0365>
HIT/BASIC,<4.143,360,0.0393>,<0,0,1>,<4.1432,0.0009,0.0348>
HIT/BASIC,<4.143,60,0.0393>,<0,0,1>,<4.1431,59.9985,0.0354>
ENDMEAS/
A4 =ALIGNMENT/START,RECALL:A3,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,TOPPLN
ALIGNMENT/TRANS,ZAXIS,TOPPLN
ALIGNMENT/TRANS,XAXIS,MANID
ALIGNMENT/TRANS,YAXIS,MANID
ALIGNMENT/ROTATE,XPLUS,TO,ALIGNLINE,ABOUT,ZPLUS
ALIGNMENT/END
MOVE/CLEARPLANE
OD =FEAT/CONTACT/CIRCLE/DEFAULT,POLAR,OUT,LEAST_SQR
THEO/<0,180,0>,<0,0,1>,8.7205,0
ACTL/<0.0003,189.282,0>,<0,0,1>,8.7192,0
TARG/<0,180,0>,<0,0,1>
START ANG=90,END ANG=90
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=5,DEPTH=-0.05,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=YES
HIT/BASIC,<4.3602,90,-0.05>,<0,1,0>,<4.3599,89.999,-0.0498>
MOVE/CLEARPLANE
HIT/BASIC,<4.3603,162,-0.05>,<-0.9510565,0.309017,0>,<4.3597,162.0045,-0.0496>
MOVE/CLEARPLANE
HIT/BASIC,<4.3603,234,-0.05>,<-0.5877853,-0.809017,0>,<4.3597,233.9908,-0.0497>
MOVE/CLEARPLANE
HIT/BASIC,<4.3602,306,-0.05>,<0.5877853,-0.809017,0>,<4.3598,306.0118,-0.0497>
MOVE/CLEARPLANE
HIT/BASIC,<4.3602,18,-0.05>,<0.9510565,0.309017,0>,<4.3589,17.9889,-0.0496>
ENDMEAS/
A5 =ALIGNMENT/START,RECALL:A4,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,TOPPLN
ALIGNMENT/TRANS,ZAXIS,TOPPLN
ALIGNMENT/TRANS,XAXIS,OD
ALIGNMENT/TRANS,YAXIS,OD
ALIGNMENT/ROTATE,XPLUS,TO,ALIGNLINE,ABOUT,ZPLUS
ALIGNMENT/END
ENDGROUP/ID=GRP1
FEAUTRES =GROUP/SHOWALLPARAMS=YES
COMMENT/REPT,
Outside Diameter
DIM L1= LOCATION OF CIRCLE OD UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX MEAS NOMINAL +TOL -TOL DEV OUTTOL
D 8.7192 8.7205 0.0040 0.0040 -0.0013 0.0000 -#--
END OF DIMENSION L1
MOVE/CLEARPLANE
CBORE =FEAT/CONTACT/CIRCLE/DEFAULT,POLAR,IN,LEAST_SQR
THEO/<0,0,0>,<0,0,1>,7.8543
ACTL/<0.0007,49.329,0>,<0,0,1>,7.8497
TARG/<0,0,0>,<0,0,1>
START ANG=18,END ANG=18
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=7,DEPTH=0.015,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=YES
HIT/BASIC,<3.9272,18,-0.015>,<-0.9510565,-0.309017,0>,<3.9248,18.0154,-0.0146>
MOVE/CLEARPLANE
HIT/BASIC,<3.9272,69.4286,-0.015>,<-0.3513748,-0.9362349,0>,<3.9262,69.4378,-0.0146>
MOVE/CLEARPLANE
HIT/BASIC,<3.9271,120.8571,-0.015>,<0.5128993,-0.8584488,0>,<3.9248,120.8427,-0.0145>
MOVE/CLEARPLANE
HIT/BASIC,<3.9271,172.2857,-0.015>,<0.9909498,-0.1342333,0>,<3.9245,172.29,-0.0146>
MOVE/CLEARPLANE
HIT/BASIC,<3.9271,223.7143,-0.015>,<0.7227949,0.6910626,0>,<3.9243,223.7294,-0.0145>
MOVE/CLEARPLANE
HIT/BASIC,<3.9272,275.1429,-0.015>,<-0.0896393,0.9959743,0>,<3.9241,275.1413,-0.0146>
MOVE/CLEARPLANE
HIT/BASIC,<3.9272,326.5714,-0.015>,<-0.8345733,0.550897,0>,<3.9254,326.5628,-0.0146>
MOVE/CLEARPLANE
ENDMEAS/
COMMENT/REPT,
Cbore Diameter
DIM L2= LOCATION OF CIRCLE CBORE UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX MEAS NOMINAL +TOL -TOL DEV OUTTOL
D 7.8497 7.8543 0.0040 0.0040 -0.0046 0.0006 <---
END OF DIMENSION L2
MOVE/CLEARPLANE
PLN3 =FEAT/CONTACT/PLANE/DEFAULT,POLAR,NONE,LEAST_SQR
THEO/<0,0,-0.0394>,<0,0,1>
ACTL/<0.0002,11.5508,-0.036>,<0.0000124,-0.000195,1>
TARG/<0,0,-0.0394>,<0,0,1>
ANGLE VEC=<COS(DEG2RAD(326)),SIN(DEG2RAD(326)),0>,RADIAL
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=6,NUMROWS=1
SPACER=(4.881+7.853)/4
AVOIDANCE MOVE=NO
SHOW HITS=YES
HIT/BASIC,<3.1835,326,-0.0394>,<0,0,1>,<3.1836,326.002,-0.0367>
HIT/BASIC,<3.1835,26,-0.0394>,<0,0,1>,<3.1838,26.0034,-0.0351>
HIT/BASIC,<3.1835,86,-0.0394>,<0,0,1>,<3.1836,85.9973,-0.0355>
HIT/BASIC,<3.1835,146,-0.0394>,<0,0,1>,<3.1833,145.9992,-0.0362>
HIT/BASIC,<3.1835,206,-0.0394>,<0,0,1>,<3.1834,206.0021,-0.0353>
HIT/BASIC,<3.1835,266,-0.0394>,<0,0,1>,<3.1835,266.0021,-0.0371>
ENDMEAS/
MOVE/CLEARPLANE
ID =FEAT/CONTACT/CIRCLE/DEFAULT,POLAR,IN,LEAST_SQR
THEO/<0,0,-0.0393>,<0,0,1>,4.881
ACTL/<0.0002,183.9184,-0.0393>,<0,0,1>,4.8792
TARG/<0,0,-0.0393>,<0,0,1>
START ANG=266,END ANG=266
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=7,DEPTH=0.05,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=YES
HIT/BASIC,<2.4405,266,-0.0893>,<0.0697565,0.9975641,0>,<2.4393,266.0162,-0.089>
HIT/BASIC,<2.4405,317.4286,-0.0893>,<-0.7364345,0.6765088,0>,<2.4392,317.3982,-0.0888>
HIT/BASIC,<2.4405,8.8571,-0.0893>,<-0.9880753,-0.1539714,0>,<2.4401,8.8674,-0.0888>
HIT/BASIC,<2.4405,60.2857,-0.0893>,<-0.4956752,-0.868508,0>,<2.439,60.3156,-0.0889>
HIT/BASIC,<2.4405,111.7143,-0.0893>,<0.3699784,-0.9290404,0>,<2.4398,111.6962,-0.0887>
HIT/BASIC,<2.4405,163.1429,-0.0893>,<0.9570308,-0.2899864,0>,<2.4396,163.1388,-0.0881>
HIT/BASIC,<2.4405,214.5714,-0.0893>,<0.8234194,0.5674332,0>,<2.4401,214.5988,-0.0887>
ENDMEAS/
COMMENT/REPT,
Inside Diameter
DIM L3= LOCATION OF CIRCLE ID UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX MEAS NOMINAL +TOL -TOL DEV OUTTOL
D 4.8792 4.8810 0.0040 0.0040 -0.0018 0.0000 -#--
END OF DIMENSION L3
MOVE/CLEARPLANE
TABLE =FEAT/CONTACT/PLANE/DEFAULT,POLAR,NONE,LEAST_SQR
THEO/<0,0,-0.1575>,<0,0,1>
ACTL/<0.0002,345.7251,-0.1585>,<0.0001795,-0.0000062,1>
TARG/<0,0,-0.1575>,<0,0,1>
ANGLE VEC=<1,0,0>,RADIAL
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=6,NUMROWS=1
SPACER=ID.RAD.MEAS-.1
AVOIDANCE MOVE=NO
SHOW HITS=YES
HIT/BASIC,<2.3396,0,-0.1575>,<0,0,1>,<2.3399,359.9991,-0.1588>
HIT/BASIC,<2.3396,60,-0.1575>,<0,0,1>,<2.3397,59.9967,-0.1587>
HIT/BASIC,<2.3396,120,-0.1575>,<0,0,1>,<2.3396,119.9962,-0.1583>
HIT/BASIC,<2.3396,180,-0.1575>,<0,0,1>,<2.3394,180.0027,-0.158>
HIT/BASIC,<2.3396,240,-0.1575>,<0,0,1>,<2.3396,240.0061,-0.1583>
HIT/BASIC,<2.3396,300,-0.1575>,<0,0,1>,<2.3397,300.0005,-0.1587>
ENDMEAS/
COMMENT/REPT,
Overall Thickness
DIM DIST1= 3D DISTANCE FROM PLANE TABLE TO PLANE TOPPLN,SHORTEST=OFF,NO_RADIUS UNITS=IN,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH
AX MEAS NOMINAL +TOL -TOL DEV OUTTOL
M 0.1585 0.1575 0.0040 0.0040 0.0010 0.0000 --#-
COMMENT/REPT,
Center Thickness
DIM DIST2= 3D DISTANCE FROM PLANE PLN3 TO PLANE TABLE,SHORTEST=OFF,NO_RADIUS UNITS=IN,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH
AX MEAS NOMINAL +TOL -TOL DEV OUTTOL
M 0.1225 0.1181 0.0040 0.0040 0.0044 0.0004 --->
MOVE/CLEARPLANE
MOVE/POINT,NORMAL,<0,0,0.5>
ENDGROUP/ID=FEAUTRES
PROGRAM_END=GROUP/SHOWALLPARAMS=YES
PROGRAM_END =LABEL/
PROGRAM_NOTIFICATION =GROUP/SHOWALLPARAMS=NO
ENDGROUP/ID=PROGRAM_NOTIFICATION
$$ NO,
code to send final cmm report to file - change nothing here .......
PRINT/REPORT,EXEC MODE=END,$
TO_FILE=ON,OVERWRITE=REPORT_NAME, OUTPUT_FORMAT/PDF,$
RESET_REPORT=YES,AUTO OPEN=OFF,$
TO_PRINTER=OFF,COPIES=1,$
TO_DMIS_REPORT=OFF,FILE_OPTION=INDEX,FILENAME=,$
REPORT_THEORETICALS=NONE,REPORT_FEATURE_WITH_DIMENSIONS=NO,$
TO_EXCEL=OFF,$
PREVIOUS_RUNS=KEEP_INSTANCES
ENDGROUP/ID=PROGRAM_END
Edit: Noticed the program_notification group was closed. No excel output there, but heres the code for that
PROGRAM_NOTIFICATION =GROUP/SHOWALLPARAMS=YES
PART_COMPLETE =FILE/OPEN,F:\SECURE\INSPECTION\CMM PROGRAMS_TEMPORARY_PCDMIS\TEMPPARTSTOMOVE\TEMPPARTSTOMOVE.TXT,APPEND
ASSIGN/PARTNAME=GETPROGRAMINFO("PARTNAME")
FILE/WRITELINE,PART_COMPLETE, "MOVE PROGRAM : "+PARTNAME
FILE/CLOSE,PART_COMPLETE,KEEP
ENDGROUP/ID=PROGRAM_NOTIFICATION
