hexagon logo
Register Sign in
  • State Not Answered
  • Replies 68 replies
  • Subscribers 224 subscribers
  • Views 1064 views
  • Users 0 members are here
Options
Related

Checking an CWW circle

sscandlon

I am struggling with what seems to be a simple part it’s three holes all in line the datum’s are based on one circle that’s measured CWW but when I try to do an auto feature the probe crashes into the part and then it can’t locate the other two holes.  any suggestions on how to set up the alignment again it’s based off of the middle outside radius and the small bore to the right of the middle bore.

Parents
  • 0 in reply to sscandlon

    maybe try anywhere between .01-.05. .001 is really small so if those holes are smaller than nominal more than .001 its going to crash

  • 0 in reply to sscandlon

    yes define the clearplane after your a3 manual alignment. Edit : after the A3_DCC1

  • 0 in reply to Zafra

    I changed it to .02 is that why i was having those issues with it crashing into the part ?

  • 0 in reply to sscandlon

    no it was crashing because you weren't using any clearance moves or avoidance moves

  • 0 in reply to Zafra

    I had the clearance cube activated . If i put the  "CLEARP/ZPLUS,0.5,ZPLUS,0,ON" after the third alignment will that fix it ?

  • 0 in reply to sscandlon

    Never used the clearance cube so you may have to turn that off, once you define your clearplane you will have to go in and add a "MOVE/CLEARPLANE" before each feature. similar to this.

    A3           =ALIGNMENT/START,RECALL:A2,LIST=YES
                ALIGNMENT/LEVEL,ZPLUS,ALIGNPLN
                ALIGNMENT/TRANS,XAXIS,READPOINT
                ALIGNMENT/TRANS,YAXIS,READPOINT
                ALIGNMENT/TRANS,ZAXIS,P1
                ALIGNMENT/ROTATE,XPLUS,TO,LIN1,ABOUT,ZPLUS
              ALIGNMENT/END
              CLEARP/ZPLUS,0.5,ZPLUS,0,ON
              MOVE/CLEARPLANE
MANOD        =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
              THEO/<0,14.5856,-0.1181>,<0,0,1>,29.2244,0
              ACTL/<0.1789,14.6053,-0.1181>,<0,0,1>,29.237,0
              TARG/<0,14.5856,-0.1181>,<0,0,1>
              START ANG=45,END ANG=45
              ANGLE VEC=<1,0,0>
              DIRECTION=CW
              SHOW FEATURE PARAMETERS=NO
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=4,DEPTH=-0.05,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0.1
                AVOIDANCE MOVE=NO
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<10.3324,24.918,-0.1681>,<0.7071068,0.7071068,0>,<10.442,25.0272,-0.1681>
                MOVE/CLEARPLANE
                HIT/BASIC,<10.3324,4.2532,-0.1681>,<0.7071068,-0.7071068,0>,<10.41,4.1756,-0.1681>
                MOVE/CLEARPLANE
                HIT/BASIC,<-10.3324,4.2532,-0.1681>,<-0.7071068,-0.7071068,0>,<-10.2431,4.342,-0.1681>
                MOVE/CLEARPLANE
                HIT/BASIC,<-10.3324,24.918,-0.1681>,<-0.7071068,0.7071068,0>,<-10.2503,24.8366,-0.1681>
              ENDMEAS/
A4           =ALIGNMENT/START,RECALL:A3,LIST=YES
                ALIGNMENT/LEVEL,ZPLUS,ALIGNPLN
                ALIGNMENT/TRANS,XAXIS,MANOD
                ALIGNMENT/TRANS,YAXIS,MANOD
                ALIGNMENT/TRANS,ZAXIS,P1
                ALIGNMENT/ROTATE,XPLUS,TO,LIN1,ABOUT,ZPLUS
              ALIGNMENT/END
              MOVE/CLEARPLANE
TOPPLNPT1    =FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
              THEO/<((SQRT((MANOD.HIT[4].TX)^2+(MANOD.HIT[4].TY)^2))-.0266),180+(RAD2DEG(ATAN(MANOD.HIT[4].TY/MANOD.HIT[4].TX))),-0.1239>,<0,0,1>
              ACTL/<14.5833,135.5486,-0.114>,<0,0,1>
              TARG/<((SQRT((MANOD.HIT[4].X)^2+(MANOD.HIT[4].Y)^2))-.0266),180+(RAD2DEG(ATAN(MANOD.HIT[4].Y/MANOD.HIT[4].X))),-0.1239>,<0,0,1>
              SNAP=NO
              SHOW FEATURE PARAMETERS=NO
              SHOW CONTACT PARAMETERS=NO

  • 0 in reply to Zafra 

     
STARTUP    =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
            ALIGNMENT/END
            MODE/MANUAL
            PREHIT/0.001
            RETRACT/0.001
            FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;MEAS,NOM,TOL,DEV,OUTTOL, , 
            TEMPCOMP/METHOD = AUTOMATIC,MATERIAL = Zerodur; Nexcera,CTE=0
              ,SET WARNING LIMIT = FALSE,MINIMUM = 10,MAXIMUM = 40
              ,PART SENSOR NUM=DEFAULT,X SCALE= 20,Y SCALE= 20,Z SCALE= 20,PART TEMP=20
            LOADPROBE/SPHERE PROBE
            TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
            MANRETRACT/0.02
PLN1       =FEAT/PLANE,CARTESIAN,TRIANGLE
            THEO/<-0.0144,0.0352,0.032>,<0,0,1>
            ACTL/<-0.0144,0.0352,0.032>,<0,0,1>
            MEAS/PLANE,4
              HIT/BASIC,NORMAL,<-0.4804,0.1425,0.032>,<0,0,1>,<-0.4804,0.1425,0.032>,USE THEO=YES
              HIT/BASIC,NORMAL,<-0.4858,-0.095,0.032>,<0,0,1>,<-0.4858,-0.095,0.032>,USE THEO=YES
              MOVE/POINT,NORMAL,<0.459,0.1818,0.0624>
              HIT/BASIC,NORMAL,<0.4496,-0.0883,0.032>,<0,0,1>,<0.4496,-0.0883,0.032>,USE THEO=YES
              HIT/BASIC,NORMAL,<0.459,0.1818,0.032>,<0,0,1>,<0.459,0.1818,0.032>,USE THEO=YES
            ENDMEAS/
CIR1       =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
            THEO/<0,0,0.1164>,<0,0,1>,0.725,0
            ACTL/<0,0,0.1164>,<0,0,1>,0.725,0
            TARG/<0,0,0.1164>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=YES
              VOID DETECTION=NO
              REMEASURE=NO
              SURFACE=THICKNESS_NONE,0
              MEASURE MODE=NOMINALS
              RMEAS=NONE,NONE,NONE
              AUTO WRIST=NO
              GRAPHICAL ANALYSIS=NO
              FEATURE LOCATOR=NO,NO,""
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=5,DEPTH=-0.04,PITCH=0
              SAMPLE METHOD=SAMPLE_HITS
              SAMPLE HITS=0,SPACER=0
              AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=YES
              HIT/BASIC,<0.3625,0,0.0764>,<1,0,0>,<0.3625,0,0.0764>
              HIT/BASIC,<0.112,0.3448,0.0764>,<0.309017,0.9510565,0>,<0.112,0.3448,0.0764>
              HIT/BASIC,<-0.2933,0.2131,0.0764>,<-0.809017,0.5877853,0>,<-0.2933,0.2131,0.0764>
              HIT/BASIC,<-0.2933,-0.2131,0.0764>,<-0.809017,-0.5877853,0>,<-0.2933,-0.2131,0.0764>
              HIT/BASIC,<0.112,-0.3448,0.0764>,<0.309017,-0.9510565,0>,<0.112,-0.3448,0.0764>
            ENDMEAS/
CIR2       =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
            THEO/<0.625,0,0.032>,<0,0,1>,0.134
            ACTL/<0.625,0,0.032>,<0,0,1>,0.134
            TARG/<0.625,0,0.032>,<0,0,1>
            START ANG=0,END ANG=360
            ANGLE VEC=<1,0,0>
            DIRECTION=CCW
            SHOW FEATURE PARAMETERS=YES
              VOID DETECTION=NO
              REMEASURE=NO
              SURFACE=THICKNESS_NONE,0
              MEASURE MODE=NOMINALS
              RMEAS=NONE,NONE,NONE
              AUTO WRIST=NO
              GRAPHICAL ANALYSIS=NO
              FEATURE LOCATOR=NO,NO,""
            SHOW CONTACT PARAMETERS=YES
              NUMHITS=4,DEPTH=0.02,PITCH=0
              SAMPLE METHOD=SAMPLE_HITS
              SAMPLE HITS=0,SPACER=0
              AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
              FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
            SHOW HITS=YES
              HIT/BASIC,<0.692,0,0.012>,<-1,0,0>,<0.692,0,0.012>
              HIT/BASIC,<0.625,0.067,0.012>,<0,-1,0>,<0.625,0.067,0.012>
              HIT/BASIC,<0.558,0,0.012>,<1,0,0>,<0.558,0,0.012>
              HIT/BASIC,<0.625,-0.067,0.012>,<0,1,0>,<0.625,-0.067,0.012>
            ENDMEAS/
LIN1       =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
            THEO/<0,0,0.1164>,<0.9910104,0,-0.1337851>
            ACTL/<0,0,0.1164>,<0.9910104,0,-0.1337851>
            CONSTR/LINE,BF,3D,CIR1,CIR2,,
            OUTLIER_REMOVAL/OFF,3
            FILTER/OFF,WAVELENGTH=0

  • 0 in reply to sscandlon

    Ok I'm starting over from here how would you align this and where would you add the clear plane ?

  • 0 in reply to sscandlon

    Alignment looked okay. After you do your alignment and set the Z Axis, define the clearplane, then whenever you do an auto circle, or any auto feature it will automatically put a move/clearplane move in before the feature. 

    Probably don't have to restart, all you need to do is define the clearplane and put a move/clearplane before your features. 

Reply
  • 0 in reply to sscandlon

    Alignment looked okay. After you do your alignment and set the Z Axis, define the clearplane, then whenever you do an auto circle, or any auto feature it will automatically put a move/clearplane move in before the feature. 

    Probably don't have to restart, all you need to do is define the clearplane and put a move/clearplane before your features. 

Children
  • 0 in reply to Zafra

    ok thank you ill let you know if I've fixed it !

  • 0 in reply to Zafra 

    STARTUP    =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
            ALIGNMENT/END
            MODE/MANUAL
            PREHIT/0.001
            RETRACT/0.001
            FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;MEAS,NOM,TOL,DEV,OUTTOL, , 
            TEMPCOMP/METHOD = AUTOMATIC,MATERIAL = Zerodur; Nexcera,CTE=0
              ,SET WARNING LIMIT = FALSE,MINIMUM = 10,MAXIMUM = 40
              ,PART SENSOR NUM=DEFAULT,X SCALE= 25.6566,Y SCALE= 25.2152,Z SCALE= 25.9439,PART TEMP=25.4915
            LOADPROBE/SPHERE PROBE
            TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
            MANRETRACT/0.02
MAN_ALIGN  =GROUP/SHOWALLPARAMS=YES
PLN1         =FEAT/PLANE,CARTESIAN,TRIANGLE
              THEO/<-0.0144,0.0352,0.032>,<0,0,1>
              ACTL/<5.5957,3.0992,-15.1783>,<-0.0002403,-0.0033879,0.9999942>
              MEAS/PLANE,4
                HIT/BASIC,NORMAL,<-0.4804,0.1425,0.032>,<0,0,1>,<5.1306,3.2108,-15.1782>,USE THEO=YES
                HIT/BASIC,NORMAL,<-0.4858,-0.095,0.032>,<0,0,1>,<5.1306,2.9789,-15.1787>,USE THEO=YES
                MOVE/POINT,NORMAL,<0.459,0.1818,0.0624>
                HIT/BASIC,NORMAL,<0.4496,-0.0883,0.032>,<0,0,1>,<6.0608,2.979,-15.1788>,USE THEO=YES
                HIT/BASIC,NORMAL,<0.459,0.1818,0.032>,<0,0,1>,<6.0608,3.2279,-15.1776>,USE THEO=YES
              ENDMEAS/
CIR1         =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
              THEO/<0,0,0.1164>,<0,0,1>,0.725,0
              ACTL/<5.5871,3.1105,0.1164>,<0,0,1>,0.7275,0
              TARG/<0,0,0.1164>,<0,0,1>
              START ANG=0,END ANG=360
              ANGLE VEC=<1,0,0>
              DIRECTION=CCW
              SHOW FEATURE PARAMETERS=YES
                VOID DETECTION=NO
                REMEASURE=NO
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=5,DEPTH=-0.04,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0
                AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<0.3625,0,0.0764>,<1,0,0>,<5.9516,3.123,-15.14>
                HIT/BASIC,<0.112,0.3448,0.0764>,<0.309017,0.9510565,0>,<5.7174,3.4478,-15.1386>
                HIT/BASIC,<-0.2933,0.2131,0.0764>,<-0.809017,0.5877853,0>,<5.3127,3.3532,-15.1455>
                HIT/BASIC,<-0.2933,-0.2131,0.0764>,<-0.809017,-0.5877853,0>,<5.2815,2.9183,-15.1454>
                HIT/BASIC,<0.112,-0.3448,0.0764>,<0.309017,-0.9510565,0>,<5.4471,2.7734,-15.1454>
              ENDMEAS/
CIR2         =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
              THEO/<0.625,0,0.032>,<0,0,1>,0.134
              ACTL/<6.2157,3.1099,0.032>,<0,0,1>,0.1334
              TARG/<0.625,0,0.032>,<0,0,1>
              START ANG=0,END ANG=360
              ANGLE VEC=<1,0,0>
              DIRECTION=CCW
              SHOW FEATURE PARAMETERS=YES
                VOID DETECTION=NO
                REMEASURE=NO
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=4,DEPTH=0.02,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0
                AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<0.692,0,0.012>,<-1,0,0>,<6.2788,3.1318,-15.2127>
                HIT/BASIC,<0.625,0.067,0.012>,<0,-1,0>,<6.2288,3.1752,-15.2127>
                HIT/BASIC,<0.558,0,0.012>,<1,0,0>,<6.1555,3.1388,-15.2127>
                HIT/BASIC,<0.625,-0.067,0.012>,<0,1,0>,<6.1992,3.0453,-15.2127>
              ENDMEAS/
LIN1         =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
              THEO/<0,0,0.1164>,<0.9910104,0,-0.1337851>
              ACTL/<5.5871,3.1105,0.1164>,<0.9911095,-0.0009167,-0.1330457>
              CONSTR/LINE,BF,3D,CIR1,CIR2,,
              OUTLIER_REMOVAL/OFF,3
              FILTER/OFF,WAVELENGTH=0
A1           =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
                ALIGNMENT/LEVEL,ZPLUS,PLN1
                ALIGNMENT/TRANS,ZAXIS,PLN1
                ALIGNMENT/TRANS,XAXIS,CIR2
                ALIGNMENT/TRANS,YAXIS,CIR2
                ALIGNMENT/ROTATE,XPLUS,TO,LIN1,ABOUT,ZPLUS
              ALIGNMENT/END
              CLEARP/ZPLUS,0.5,ZPLUS,0,ON
            ENDGROUP/ID=MAN_ALIGN
DCC_ALIGN  =GROUP/SHOWALLPARAMS=YES
              MODE/DCC
PLN1         =FEAT/PLANE,CARTESIAN,TRIANGLE
              THEO/<-0.6394,0.0352,0>,<0,0,1>
              ACTL/<-0.6394,0.0353,0.0004>,<0.0004593,-0.0026734,0.9999963>
              MEAS/PLANE,4
                MOVE/CLEARPLANE
                HIT/BASIC,NORMAL,<-1.1054,0.1425,0>,<0,0,1>,<-1.1054,0.1426,0.0006>,USE THEO=YES
                HIT/BASIC,NORMAL,<-1.1108,-0.095,0>,<0,0,1>,<-1.1109,-0.0949,0.0006>,USE THEO=YES
                MOVE/POINT,NORMAL,<-0.0615,0.0948,0.703>
                HIT/BASIC,NORMAL,<-0.1754,-0.0883,0>,<0,0,1>,<-0.1755,-0.0882,-0.0004>,USE THEO=YES
                HIT/BASIC,NORMAL,<-0.166,0.1818,0>,<0,0,1>,<-0.166,0.1819,0.0008>,USE THEO=YES
              ENDMEAS/
              MOVE/CLEARPLANE
              MANRETRACT/0.05
CIR1         =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
              THEO/<-0.625,0,0.0844>,<0,0,1>,0.725,0
              ACTL/<-0.625,0,0.0844>,<0,0,1>,0.725,0
              TARG/<-0.625,0,0.0844>,<0,0,1>
              START ANG=0,END ANG=360
              ANGLE VEC=<1,0,0>
              DIRECTION=CCW
              SHOW FEATURE PARAMETERS=YES
                VOID DETECTION=NO
                REMEASURE=NO
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                CIRCULAR MOVES=STRAIGHT
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=5,DEPTH=-0.04,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0
                AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<-0.2625,0,0.0444>,<1,0,0>,<-0.2625,0,0.0444>
                HIT/BASIC,<-0.513,0.3448,0.0444>,<0.309017,0.9510565,0>,<-0.513,0.3448,0.0444>
                HIT/BASIC,<-0.9183,0.2131,0.0444>,<-0.809017,0.5877853,0>,<-0.9183,0.2131,0.0444>
                HIT/BASIC,<-0.9183,-0.2131,0.0444>,<-0.809017,-0.5877853,0>,<-0.9183,-0.2131,0.0444>
                HIT/BASIC,<-0.513,-0.3448,0.0444>,<0.309017,-0.9510565,0>,<-0.513,-0.3448,0.0444>
              ENDMEAS/
              MOVE/CLEARPLANE
CIR2         =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
              THEO/<0,0,0>,<0,0,1>,0.134
              ACTL/<-5.5864,-3.1176,15.2219>,<0.0002356,0.0033883,0.9999942>,0.134
              TARG/<0,0,0>,<0,0,1>
              START ANG=0,END ANG=360
              ANGLE VEC=<1,0,0>
              DIRECTION=CCW
              SHOW FEATURE PARAMETERS=YES
                VOID DETECTION=NO
                REMEASURE=NO
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                CIRCULAR MOVES=STRAIGHT
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=4,DEPTH=0.02,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0
                AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<0.067,0,-0.02>,<-1,0,0>,<-5.5194,-3.1176,15.2019>
                HIT/BASIC,<0,0.067,-0.02>,<0,-1,0>,<-5.5865,-3.0507,15.2017>
                HIT/BASIC,<-0.067,0,-0.02>,<1,0,0>,<-5.6534,-3.1177,15.2019>
                HIT/BASIC,<0,-0.067,-0.02>,<0,1,0>,<-5.5863,-3.1847,15.2022>
              ENDMEAS/
LIN1         =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
              THEO/<-0.625,0,0.0844>,<0.9910104,0,-0.1337851>
              ACTL/<-5.5864,-3.1176,15.2219>,<0.3056531,0.1920633,-0.9325706>
              CONSTR/LINE,BF,3D,CIR1,CIR2,,
              OUTLIER_REMOVAL/OFF,3
              FILTER/OFF,WAVELENGTH=0
A1           =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
                ALIGNMENT/LEVEL,ZPLUS,PLN1
                ALIGNMENT/TRANS,ZAXIS,PLN1
                ALIGNMENT/TRANS,XAXIS,CIR2
                ALIGNMENT/TRANS,YAXIS,CIR2
                ALIGNMENT/ROTATE,XPLUS,TO,LIN1,ABOUT,ZPLUS
              ALIGNMENT/END
              CLEARP/ZPLUS,0.5,ZPLUS,0,ON
            ENDGROUP/ID=DCC_ALIGN

  • 0 in reply to sscandlon

    when it goes to check cir1 its still running into the part

  • 0 in reply to sscandlon

    change Cir1 to IN instead of out. its trying to check it like it's an OD, sometimes my models do the same thing, when i generate auto features for an inside diameter it thinks it's an outside diameter. 

  • 0 in reply to sscandlon

    ohh oops. Bigger prehit then, you're still on .001

    PREHIT/0.05
    RETRACT/0.05

  • 0 in reply to Zafra

    Ok it now moving away enough but when it goes to hit the second hit it doesn’t go near the part 

  • 0 in reply to sscandlon

    either use circular moves, or add clearplanes in between each hit of the auto circle 

    CIRCULAR MOVES=STRAIGHT

  • 0 in reply to Zafra

    Also, you shouldnt be naming the features the same thing, you have two cir1's, two pln1's etc. etc. same with alignments 

© 2024 Hexagon AB and/or its subsidiaries. Privacy Policy | Cloud Services Agreement