hexagon logo
Register Sign in
  • Replies 5 replies
  • Subscribers 31 subscribers
  • Views 72 views
  • Users 0 members are here
Options
Related

Nominal Dimension during programming True Position

Casonroy3
I am using a Romer Arm Infinite 2.0 with PCSmileymis 2014 software. I am checking the True Position on 1.750" diameter bore. I probed this bore as a cylinder. I went into Legacy Mode and defined my Datums (A,B,C). When going into the advanced button to enter the nominal dimensions for the -X- and -Y- axis. I am also in the current alignment mode. When entering the Nominal dimension for the -X- axis the software takes the dimension. When I enter the Nominal dimension for the -Y- axis the -X- axis converts back to its original value. I went into the Summary mode and corrected the X & Y values, and the software retains these values. When viewing the inspection report the nominal values revert back to the incorrect nominal values. Please Help me correct this issue!!!!.......Thank You
  • If you put a "+0 " after your nominals in command mode, it should take care of that. I used to have a problem with my nominals changing back and this took care of that. See example below. 



    DIM LOC 155= POSITION OF CIRCLE CIR 154  UNITS=IN ,$
GRAPH=OFF  TEXT=OFF  MULT=10.00  OUTPUT=NONE  FIT TO DATUMS=OFF  DEV PERPEN CENTERLINE=OFF  DISPLAY=DIAMETER
AX    NOMINAL       +TOL       -TOL      BONUS       MEAS        DEV     OUTTOL
X       0.000+0                                       0.000      0.000           
Y       0.000+0                                       0.000      0.000           
DF      1.190+0      0.030      0.030                 1.182     -0.008      0.000 -------#------------
TP        RFS      0.028                 0.000      0.000      0.000      0.000 #-------------------
END OF DIMENSION LOC 155
  • I am using a Romer Arm Infinite 2.0 with PCSmileymis 2014 software. I am checking the True Position on 1.750" diameter bore. I probed this bore as a cylinder. I went into Legacy Mode and defined my Datums (A,B,C). When going into the advanced button to enter the nominal dimensions for the -X- and -Y- axis. I am also in the current alignment mode. When entering the Nominal dimension for the -X- axis the software takes the dimension. When I enter the Nominal dimension for the -Y- axis the -X- axis converts back to its original value. I went into the Summary mode and corrected the X & Y values, and the software retains these values. When viewing the inspection report the nominal values revert back to the incorrect nominal values. Please Help me correct this issue!!!!.......Thank You

    Are you using legacy or NON Legacy? The way this is described it sounds like your are using exact measure.

    Update the actual feature nominals you are dimensioning. Then you shouldn't have any adjustments to be made in the advanced tab.

    Brian
  • Mr. Staral, thanks for your help......but the plus zero did not work for me. It still reverts back to its original number.
  • Brian.....Thanks for your help......I am not in the legacy mode.....my apologies for mis-leading you. The feature nominal were updated in the summary mode and this had no effect when viewing the Inspection report, the nominal are still incorrect
  • Brian.....Thanks for your help......I am not in the legacy mode.....my apologies for mis-leading you. The feature nominal were updated in the summary mode and this had no effect when viewing the Inspection report, the nominal are still incorrect

    Ok. I am just gonna throw some darts. Did you happen to delete and recreate your true position? Once you make changes in summary mode and open up the inspection report, be sure to click the refresh button.Are you in the correct workplane? Is your alignment different then your A, B, C Datum structure?

    Brian
© 2024 Hexagon AB and/or its subsidiaries. Privacy Policy | Cloud Services Agreement