Hexagon OPTIV 663 - Timeout Error during focus?

Looking for assistance with the following error shown in the image below. The error started popping up during a programs execution, even after running the routine many times without issues.. Does anyone know the cause of this error? Nothing changed PC wise, like software updates etc...machine is offline from the internet.

It error occurs strictly when using the camera, since its trying to focus
The machine errors out when measuring the circles, but I have witnessed its not focusing on points as well...also received the same error
This seems to be a communication issue on this machine only, a as I have never witnessed this happening on our other OPTIV 663
- I can watch PC-DMIS read the code for the circle, the machine does physically move and then finds the focal spot (the circle is crisp on live view screen) but there is a delay in the software and that's when I know it will fault out...
- I can click the play button multiple times in the execution window to repeat the focus step, and the machine will eventually generate the actuals and continue
I have tried to change every focus settings possible, increase/decreased range, duration, etc...switched from AUTO to FULL...using assist etc...
- No matter the focus settings, the machine will still fault out during execution eventually...its an intermittent problem
- Perhaps its my edge detection settings or something else?
The software we are running is PC-DMIS 2020, on both machine as well.
I use subroutines in the program, but it will also error out if I don't use subroutines.

Any help is appreciated. Thank you.

Attached Files

Parents

DSchenk over 2 years ago

Here is the code, the circle that is measured when the error pops up is at the bottom.


SUBROUTINE/PART ROUTINE,
X_OFF = : ,
Y_OFF = : ,
Z_OFF = : ,
=
LOADPROBE/CARRIER PUCK
TIP/TIP1, SHANKIJK=-0.00016, 0, 1, ANGLE=0.03015
MOVE/POINT,NORMAL,<X_OFF,Y_OFF,90>
MOVESPEED/ 200
TOUCHSPEED/ 1
PREHIT/1
RETRACT/1
CENTER_CIR =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,3>,<0,0,1>,8.15
ACTL/<0,0,3>,<0,0,1>,8.15
TARG/<X_OFF,Y_OFF,Z_OFF>,<0,0,1>
START ANG=60,END ANG=300
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=YES
VOID DETECTION=NO
REMEASURE=NO
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
CIRCULAR MOVES=STRAIGHT
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
NUMHITS=3,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO,DISTANCE=10
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
A3_CENTER_CIRCLE=ALIGNMENT/START,RECALL:A2_FIXT_TO_PART,LIST=YES
ALIGNMENT/TRANS,XAXIS,CENTER_CIR
ALIGNMENT/TRANS,YAXIS,CENTER_CIR
ALIGNMENT/END
MOVE/POINT,NORMAL,<0,0,25>
MOVE/POINT,NORMAL,<4,-14,25>
TOUCHSPEED/ 2
C_PT1 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<1.75,-8.2,2>,<1,0,0>
ACTL/<1.75,-8.2,2>,<1,0,0>
TARG/<1.75,-8.2,2>,<1,0,0>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=1
SHOW HITS=NO
MOVE/POINT,NORMAL,<4,-12,5>
MOVE/POINT,NORMAL,<-4,-12,5>
C_PT2 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-1.75,-8.2,2>,<-1,0,0>
ACTL/<-1.75,-8.2,2>,<-1,0,0>
TARG/<-1.75,-8.2,2>,<-1,0,0>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=1
SHOW HITS=NO
C_MID =FEAT/POINT,CARTESIAN,NO
THEO/<0,-8.2,2>,<0,0,1>
ACTL/<0,-8.2,2>,<-0.0000001,0.000005,1>
CONSTR/POINT,MID,C_PT1,C_PT2
C_LINE =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
THEO/<0,0,2.5>,<0,-1,0>
ACTL/<0,0,2.5>,<0,-1,0>
CONSTR/LINE,BF,2D,CENTER_CIR,C_MID,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
A4_CENTER_POST_ROT=ALIGNMENT/START,RECALL:A3_CENTER_CIRCLE,LIST=YES
ALIGNMENT/ROTATE,YMINUS,TO,C_LINE,ABOUT,ZPLUS
ALIGNMENT/TRANS,XAXIS,CENTER_CIR
ALIGNMENT/TRANS,YAXIS,CENTER_CIR
ALIGNMENT/END
MOVE/POINT,NORMAL,<-4,-12,25>
MOVE/POINT,NORMAL,<0,11.4,25>
A_PT1 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<0,11.4,0>,<0,0,1>
ACTL/<0,11.4,0>,<0,0,1>
TARG/<0,11.4,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=25
SHOW HITS=NO
MOVE/POINT,NORMAL,<0.1,11.4,25>
MOVE/POINT,NORMAL,<-9.77269,-5.7,25>
A_PT2 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-9.87269,-5.7,0>,<0,0,1>
ACTL/<-9.87269,-5.7,0>,<0,0,1>
TARG/<-9.87269,-5.7,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=25
SHOW HITS=NO
MOVE/POINT,NORMAL,<-9.77269,-5.7,25>
MOVE/POINT,NORMAL,<9.97269,-5.7,25>
A_PT3 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<9.87269,-5.7,0>,<0,0,1>
ACTL/<9.87269,-5.7,0>,<0,0,1>
TARG/<9.87269,-5.7,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=25
SHOW HITS=NO
A_PLN =FEAT/PLANE,CARTESIAN,OUTLINE,NO,LEAST_SQR
THEO/<0,0,0>,<0,0,1>
ACTL/<0,0,0>,<0,0,1>
CONSTR/PLANE,BF,A_PT1,A_PT2,A_PT3,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
A5_MAIN_PART_ALIGN=ALIGNMENT/START,RECALL:A3_CENTER_CIRCLE,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/ROTATE,YMINUS,TO,C_LINE,ABOUT,ZPLUS
ALIGNMENT/TRANS,XAXIS,CENTER_CIR
ALIGNMENT/TRANS,YAXIS,CENTER_CIR
ALIGNMENT/TRANS,ZAXIS,A_PLN
ALIGNMENT/END
MOVE/POINT,NORMAL,<9.97269,-5.7,25>
MOVE/POINT,NORMAL,<0.1,0,25>
8.15_CIR =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,0.5>,<0,0,1>,8.15
ACTL/<0,0,0.5>,<0,0,1>,8.15
TARG/<0,0,0.5>,<0,0,1>
START ANG=59.30131,END ANG=299.30131
ANGLE VEC=<0,0,1>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=YES
VOID DETECTION=NO
REMEASURE=NO
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
CIRCULAR MOVES=STRAIGHT
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
NUMHITS=3,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO,DISTANCE=10
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/POINT,NORMAL,<0,0,25>
MOVE/POINT,NORMAL,<-55,-9.5,25>
TIP/TIP2, SHANKIJK=-1, -0.00053, -0.00016, ANGLE=0.00021
MOVE/POINT,NORMAL,<-30,-9.5,5>
7.05_TOP_PT1=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<16.5,210,0>,<0,0,1>
ACTL/<16.5,210,0>,<0,0,1>
TARG/<16.5,210,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
MOVE/POINT,NORMAL,<-30,-9.5,5>
MOVE/POINT,NORMAL,<-30,-9.5,-16>
7.05_BOT_PT1=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<17,203,-7.05>,<0,0,-1>
ACTL/<17,203,-7.05>,<0,0,-1>
TARG/<17,203,-7.05>,<0,0,-1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=2
SHOW HITS=NO
MOVE/POINT,NORMAL,<-30,-9.5,-16>
MOVE/POINT,NORMAL,<-30,-9.5,80>
TIP/TIP3, SHANKIJK=1, 0.00053, 0.00016, ANGLE=-0.00021
MOVE/POINT,NORMAL,<30,-9.5,80>
MOVE/POINT,NORMAL,<30,-9.5,5>
7.05_TOP_PT2=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<16.5,330,0>,<0,0,1>
ACTL/<16.5,330,0>,<0,0,1>
TARG/<16.5,330,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
MOVE/POINT,NORMAL,<30,-9.5,5>
MOVE/POINT,NORMAL,<30,-9.5,-16>
7.05_BOT_PT2=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<17,323,-7.05>,<0,0,-1>
ACTL/<17,323,-7.05>,<0,0,-1>
TARG/<17,323,-7.05>,<0,0,-1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=BOTH,DISTANCE=2
SHOW HITS=NO
PREHIT/1
RETRACT/1
MOVESPEED/ 20
MOVE/POINT,NORMAL,<15,13,-9.5>
7.05_BOT_PT3=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<17,83,-7.05>,<0,0,-1>
ACTL/<17,83,-7.05>,<0,0,-1>
TARG/<17,83,-7.05>,<0,0,-1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=BOTH,DISTANCE=1
SHOW HITS=NO
TOUCHSPEED/ 1
MOVE/POINT,NORMAL,<25,13,-9.5>
MOVE/POINT,NORMAL,<25,13,1.3>
PREHIT/0.5
RETRACT/0.5
7.05_TOP_PT3=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<16.5,90,0>,<0,0,1>
ACTL/<16.5,90,0>,<0,0,1>
TARG/<16.5,90,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
DATUM A_2 =FEAT/PLANE,CARTESIAN,OUTLINE,NO,LEAST_SQR
THEO/<0,0,0>,<0,0,1>
ACTL/<0,0,0>,<0,0,1>
CONSTR/PLANE,BF,7.05_TOP_PT1,7.05_TOP_PT2,7.05_TOP_PT3,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
MOVE/POINT,NORMAL,<25,13,1.3>
MOVESPEED/ 200
PREHIT/1
RETRACT/1
MOVE/POINT,NORMAL,<30,13,80>
TIP/TIP1, SHANKIJK=-0.00016, 0, 1, ANGLE=0.03015
WORKPLANE/XPLUS
MOVE/POINT,NORMAL,<0,0,90>
LOADPROBE/ZOOM
TIP/TIP1, SHANKIJK=-0.00013, 0.00217, 1, ANGLE=-0.45473
MOVE/POINT,NORMAL,<0,0,120>
5.0 CIR =FEAT/VISION/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,-0.875>,<0,0,1>,5,0,0
ACTL/<0,0,-0.875>,<0,0,1>,5,0,0
TARG/<0,0,-0.875>,<0,0,1>
ANGLE VEC=<1,0,0>
SHOW FEATURE PARAMETERS=NO
SHOW_VISION_PARAMETERS=YES
TYPE=AUTOMATIC HIT TARGET
COVERAGE=100%
COVERAGE ACTIVE TARGETS=4
MAGNIFICATION=0.65521
HIT TARGET COLOR=RED (DARK),NOMINAL COLOR=RED (HMI)
HIT TARGET=EA1,0,1,HIGH,0.46653
FILTER=NO,NO
EDGE=DOMINANT EDGE,[ ]->[|],<--,YES,-1,-1,-1,NO,Top Light=<OFF,0,OFF>,Bottom Light=<OFF,40,ON>,Ring Light=<OFF,0,OFF>
FOCUS=YES,FULL,10,NO,1,NONE,NO

Reply

DSchenk over 2 years ago

Here is the code, the circle that is measured when the error pops up is at the bottom.


SUBROUTINE/PART ROUTINE,
X_OFF = : ,
Y_OFF = : ,
Z_OFF = : ,
=
LOADPROBE/CARRIER PUCK
TIP/TIP1, SHANKIJK=-0.00016, 0, 1, ANGLE=0.03015
MOVE/POINT,NORMAL,<X_OFF,Y_OFF,90>
MOVESPEED/ 200
TOUCHSPEED/ 1
PREHIT/1
RETRACT/1
CENTER_CIR =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,3>,<0,0,1>,8.15
ACTL/<0,0,3>,<0,0,1>,8.15
TARG/<X_OFF,Y_OFF,Z_OFF>,<0,0,1>
START ANG=60,END ANG=300
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=YES
VOID DETECTION=NO
REMEASURE=NO
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
CIRCULAR MOVES=STRAIGHT
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
NUMHITS=3,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO,DISTANCE=10
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
A3_CENTER_CIRCLE=ALIGNMENT/START,RECALL:A2_FIXT_TO_PART,LIST=YES
ALIGNMENT/TRANS,XAXIS,CENTER_CIR
ALIGNMENT/TRANS,YAXIS,CENTER_CIR
ALIGNMENT/END
MOVE/POINT,NORMAL,<0,0,25>
MOVE/POINT,NORMAL,<4,-14,25>
TOUCHSPEED/ 2
C_PT1 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<1.75,-8.2,2>,<1,0,0>
ACTL/<1.75,-8.2,2>,<1,0,0>
TARG/<1.75,-8.2,2>,<1,0,0>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=1
SHOW HITS=NO
MOVE/POINT,NORMAL,<4,-12,5>
MOVE/POINT,NORMAL,<-4,-12,5>
C_PT2 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-1.75,-8.2,2>,<-1,0,0>
ACTL/<-1.75,-8.2,2>,<-1,0,0>
TARG/<-1.75,-8.2,2>,<-1,0,0>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=1
SHOW HITS=NO
C_MID =FEAT/POINT,CARTESIAN,NO
THEO/<0,-8.2,2>,<0,0,1>
ACTL/<0,-8.2,2>,<-0.0000001,0.000005,1>
CONSTR/POINT,MID,C_PT1,C_PT2
C_LINE =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
THEO/<0,0,2.5>,<0,-1,0>
ACTL/<0,0,2.5>,<0,-1,0>
CONSTR/LINE,BF,2D,CENTER_CIR,C_MID,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
A4_CENTER_POST_ROT=ALIGNMENT/START,RECALL:A3_CENTER_CIRCLE,LIST=YES
ALIGNMENT/ROTATE,YMINUS,TO,C_LINE,ABOUT,ZPLUS
ALIGNMENT/TRANS,XAXIS,CENTER_CIR
ALIGNMENT/TRANS,YAXIS,CENTER_CIR
ALIGNMENT/END
MOVE/POINT,NORMAL,<-4,-12,25>
MOVE/POINT,NORMAL,<0,11.4,25>
A_PT1 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<0,11.4,0>,<0,0,1>
ACTL/<0,11.4,0>,<0,0,1>
TARG/<0,11.4,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=25
SHOW HITS=NO
MOVE/POINT,NORMAL,<0.1,11.4,25>
MOVE/POINT,NORMAL,<-9.77269,-5.7,25>
A_PT2 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-9.87269,-5.7,0>,<0,0,1>
ACTL/<-9.87269,-5.7,0>,<0,0,1>
TARG/<-9.87269,-5.7,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=25
SHOW HITS=NO
MOVE/POINT,NORMAL,<-9.77269,-5.7,25>
MOVE/POINT,NORMAL,<9.97269,-5.7,25>
A_PT3 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<9.87269,-5.7,0>,<0,0,1>
ACTL/<9.87269,-5.7,0>,<0,0,1>
TARG/<9.87269,-5.7,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=25
SHOW HITS=NO
A_PLN =FEAT/PLANE,CARTESIAN,OUTLINE,NO,LEAST_SQR
THEO/<0,0,0>,<0,0,1>
ACTL/<0,0,0>,<0,0,1>
CONSTR/PLANE,BF,A_PT1,A_PT2,A_PT3,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
A5_MAIN_PART_ALIGN=ALIGNMENT/START,RECALL:A3_CENTER_CIRCLE,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/ROTATE,YMINUS,TO,C_LINE,ABOUT,ZPLUS
ALIGNMENT/TRANS,XAXIS,CENTER_CIR
ALIGNMENT/TRANS,YAXIS,CENTER_CIR
ALIGNMENT/TRANS,ZAXIS,A_PLN
ALIGNMENT/END
MOVE/POINT,NORMAL,<9.97269,-5.7,25>
MOVE/POINT,NORMAL,<0.1,0,25>
8.15_CIR =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,0.5>,<0,0,1>,8.15
ACTL/<0,0,0.5>,<0,0,1>,8.15
TARG/<0,0,0.5>,<0,0,1>
START ANG=59.30131,END ANG=299.30131
ANGLE VEC=<0,0,1>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=YES
VOID DETECTION=NO
REMEASURE=NO
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
CIRCULAR MOVES=STRAIGHT
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
NUMHITS=3,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO,DISTANCE=10
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/POINT,NORMAL,<0,0,25>
MOVE/POINT,NORMAL,<-55,-9.5,25>
TIP/TIP2, SHANKIJK=-1, -0.00053, -0.00016, ANGLE=0.00021
MOVE/POINT,NORMAL,<-30,-9.5,5>
7.05_TOP_PT1=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<16.5,210,0>,<0,0,1>
ACTL/<16.5,210,0>,<0,0,1>
TARG/<16.5,210,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
MOVE/POINT,NORMAL,<-30,-9.5,5>
MOVE/POINT,NORMAL,<-30,-9.5,-16>
7.05_BOT_PT1=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<17,203,-7.05>,<0,0,-1>
ACTL/<17,203,-7.05>,<0,0,-1>
TARG/<17,203,-7.05>,<0,0,-1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=2
SHOW HITS=NO
MOVE/POINT,NORMAL,<-30,-9.5,-16>
MOVE/POINT,NORMAL,<-30,-9.5,80>
TIP/TIP3, SHANKIJK=1, 0.00053, 0.00016, ANGLE=-0.00021
MOVE/POINT,NORMAL,<30,-9.5,80>
MOVE/POINT,NORMAL,<30,-9.5,5>
7.05_TOP_PT2=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<16.5,330,0>,<0,0,1>
ACTL/<16.5,330,0>,<0,0,1>
TARG/<16.5,330,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
MOVE/POINT,NORMAL,<30,-9.5,5>
MOVE/POINT,NORMAL,<30,-9.5,-16>
7.05_BOT_PT2=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<17,323,-7.05>,<0,0,-1>
ACTL/<17,323,-7.05>,<0,0,-1>
TARG/<17,323,-7.05>,<0,0,-1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=BOTH,DISTANCE=2
SHOW HITS=NO
PREHIT/1
RETRACT/1
MOVESPEED/ 20
MOVE/POINT,NORMAL,<15,13,-9.5>
7.05_BOT_PT3=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<17,83,-7.05>,<0,0,-1>
ACTL/<17,83,-7.05>,<0,0,-1>
TARG/<17,83,-7.05>,<0,0,-1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=BOTH,DISTANCE=1
SHOW HITS=NO
TOUCHSPEED/ 1
MOVE/POINT,NORMAL,<25,13,-9.5>
MOVE/POINT,NORMAL,<25,13,1.3>
PREHIT/0.5
RETRACT/0.5
7.05_TOP_PT3=FEAT/CONTACT/VECTOR POINT/DEFAULT,POLAR
THEO/<16.5,90,0>,<0,0,1>
ACTL/<16.5,90,0>,<0,0,1>
TARG/<16.5,90,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
DATUM A_2 =FEAT/PLANE,CARTESIAN,OUTLINE,NO,LEAST_SQR
THEO/<0,0,0>,<0,0,1>
ACTL/<0,0,0>,<0,0,1>
CONSTR/PLANE,BF,7.05_TOP_PT1,7.05_TOP_PT2,7.05_TOP_PT3,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
MOVE/POINT,NORMAL,<25,13,1.3>
MOVESPEED/ 200
PREHIT/1
RETRACT/1
MOVE/POINT,NORMAL,<30,13,80>
TIP/TIP1, SHANKIJK=-0.00016, 0, 1, ANGLE=0.03015
WORKPLANE/XPLUS
MOVE/POINT,NORMAL,<0,0,90>
LOADPROBE/ZOOM
TIP/TIP1, SHANKIJK=-0.00013, 0.00217, 1, ANGLE=-0.45473
MOVE/POINT,NORMAL,<0,0,120>
5.0 CIR =FEAT/VISION/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,-0.875>,<0,0,1>,5,0,0
ACTL/<0,0,-0.875>,<0,0,1>,5,0,0
TARG/<0,0,-0.875>,<0,0,1>
ANGLE VEC=<1,0,0>
SHOW FEATURE PARAMETERS=NO
SHOW_VISION_PARAMETERS=YES
TYPE=AUTOMATIC HIT TARGET
COVERAGE=100%
COVERAGE ACTIVE TARGETS=4
MAGNIFICATION=0.65521
HIT TARGET COLOR=RED (DARK),NOMINAL COLOR=RED (HMI)
HIT TARGET=EA1,0,1,HIGH,0.46653
FILTER=NO,NO
EDGE=DOMINANT EDGE,[ ]->[|],<--,YES,-1,-1,-1,NO,Top Light=<OFF,0,OFF>,Bottom Light=<OFF,40,ON>,Ring Light=<OFF,0,OFF>
FOCUS=YES,FULL,10,NO,1,NONE,NO

Children

No Data