Hello, all!
(I'm ignorant. Tear me apart!)
This is the first time I've come across this type of call out. I understand a bit about how it works, but need help with the execution.
Could someone, please, walk me through the general steps I'd take…
Good morning all. So I have run into an issue will scanning where the probe tip comes off the part 3/4 of the way into the scan of a circle. I started looking into my setting and found that the offset force for the scan was set to .003 which seemed a…
So, I have a part that is essentially a ring with an ID and an OD. I have scanned them to get the dimensions and put them on the report. The customer wants the C/S on the report as well. Is there any way to use the scans to get the C/S dimension? or do…
So, I have a part that I have to combine three adaptive circle scans. It won't let me construct a circle from those scans, so I used POINTCLOUD. I just made the scans then inserted a pointclound feature using the three scans. It lets me construct a circle…
Let me preface that I'm very new to programming, as well as, operating the CMM. So something that might seem like a obvious solution to most of you is like finding a needle in a hay stack for me, haha. Thanks!
While writing a program for a part, I have…
When I use the COP command to export TTP strategy features in PC-DMIS it works just fine. But for whatever reason when I setup the point cloud to export scanned features, it deselects only the scanned features and never exports them in my point cloud…
When i change probes during a measurement routine the probe travels all the way to the highest point in Z and then goes down to the probe tree. After changing Probes it returns to the highest Z position. Can I change this to where it just goes straight…
So, I have a part that I have to clamp down to the table and want to utilize the scan feature because its more efficient. Is there a way to jump the clamps while scanning? I have tried to separate the scan by using to begin and end degrees then trying…
Morning all,
Just wondering I have two CMM with different heights and bed sizes. Both on RC1 controllers,
I would like to know if there's a generic home move line I can enter that'll move the probe to its home position once the probe has finished…
Hello everyone, I have this part that I have to measure distance 97,01 between these pins that are at an angle, meaning they are not aligned with either X,Y,Z axis. How do I measure it, do I need to align it first, if so, what kind of alignments I need…
Hi team,
I'm new to the group and using PC-DMIS.
I have experience with other CMM softwares, but this a new CMM Global S was installed at my company.
It has a travel rack attached to the right side, a scanner HP-L.10.10, and an HR-R3.
And HP-S…
I'm experiencing an issue with my CMM using PC-DMIS. When I switch to DCC mode and begin to take points, the probe successfully takes the first point (I can hear the beep indicating it was taken), but instead of retracting afterward, it drives directly…
Hello, This is my cad model and coordinate system when I import it into pcdmis. My actual part is on CMM is placed as on the picture down left. How do I transform coordinate system to other point on my CAD model? How do I align it with my actual part…
Feature control frame asks Position of ID to Top Plane -A- and -B-. Datum -B- is 3 datum target points all at different radial distances. Would Datum -B- just be reported as separate points or do you combine all 3 for a feature? Thanks for any help.
Hello guys, I would need a bit of help as I'm trying to measure this profile of surface dimension. I've been using Hexagon Performance 7.10.7 CMM machine for about 5 months, but this is the first project in which I need to measure profile of surface depended…
The last company I worked for would make create trace field commands to require inputs from an operator to be displayed in the report to actual custom file header template. It is a little tricky for me to navigate the label template header. I haven't…
The first job I programmed CMMs at it seems that when I inserted move points in my program that it worked great and exactly like I wanted it to. I could create move points in my programs OFFLINE and they would move to the exact coordinates relative to…
Hello.
I'm trying to create a program that can measure 24 equal parts in a fixture. I've created a
program that simply shifts the origin to measure the next part. The issue arises in the alignment,
where PC-DMIS compensates, causing me to measure…
On a recent Hexagon service visit, the field engineer noticed in the setting editor that our “ContinousTempSensor” was turned off.
He explained that it continuously samples the temperature throughout the routine, but wasn’t able to dive deeper. We are…
hi everyone.
I will create a loop program for nesting jobs. I've completed the program, but I can't edit any features, which means if 2, 3, and 5 job holes are deviated, I can't adjust them. I've tried to edit the features, but the probe keeps returning…
The only "Training" I've received was 02/21-24/2021 approximately 2 1/2 days on a manual machine on PCDMIS-2019 I I'm thine only operator on any shift. we upgraded to a GLOBAL S GREEN 7,5,7 this past December. and apart from first shot/last shots involving…
It's not available under my graphic Items and this would be helpful for visualizing TIP angles in offline mode to check for clearance. I have a HH-AS8-T2.5