Problem Rotation

i have this code:

STARTUP    =ALIGNMENT/START,RECALL:,LIST=YES
            ALIGNMENT/END
            MODE/DCC
            FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, , 
            LOADPROBE/1MM
            ASSIGN/AUX=2
            IF/AUX==1
            ASSIGN/AUX=100
            END_IF/
            IF/AUX==2
            TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
            ASSIGN/AUX=200
            END_IF/
            IF/AUX==3
            ASSIGN/AUX=300
            END_IF/
            IF/AUX==4
            TIP/T1A45B0, SHANKIJK=0, 0.707, 0.707, ANGLE=0
            ASSIGN/AUX=400
            END_IF/
C1         =COMMENT/YESNO,NO,AUX

Result:
AUX = 200 OK
TIP = T1A45B0 WHY??
________
N02 VAPORIZER

tking over 14 years ago

Because that is the last tip command in the code, the demon will assume the last called. I can see the logic you're trying to apply but that isn't going to work (ahh... the demon......).

TK
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
overpsp over 14 years ago

damm... any solution?
________
LovelyWendie
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
tking over 14 years ago

damm... any solution?

Leaves a bit to figure, I see some logic but don't know what it's goal is. If the idea is to go to different portions of code depending on AUX then yes. Care to explain the intent?

TK
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
overpsp over 14 years ago

This bug of software??
I want make a script with a series of condition...
________
EXPERT INSURANCE
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
overpsp over 14 years ago

If the idea is to go to different portions of code depending on AUX then yes.

TK

How?
________
Nexium Settlement
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
tking over 14 years ago

An example, simple method.

COMMENT/DOC,***************************************************
,Menu
,***************************************************
,
MENU =LABEL/
C1 =COMMENT/INPUT,What do you need to do?
,1.... See a picture of the part on the fixture
,2.... Manually find fixture plate
,3.... DCC find the fixture points (clamps open)
,4.... Run the part
IF_GOTO/C1.INPUT=="1",GOTO = PIX
IF_GOTO/C1.INPUT=="2",GOTO = MANUAL
IF_GOTO/C1.INPUT=="3",GOTO = FIXTURE
IF_GOTO/C1.INPUT=="4",GOTO = PART
PIX =LABEL/

GOTO/MENU
GOTO/END_PROGRAM
MANUAL =LABEL/
FIXTURE =LABEL/
PART =LABEL/
END_PROGRAM=LABEL/
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
overpsp over 14 years ago

But my problem is this commands in the conditions

TIP/T1A45B0, SHANKIJK=0, 0.707, 0.707, ANGLE=0
TIP/T1A0B0, SHANKIJK=0, 0.707, 0.707, ANGLE=0
TIP/T1A45B180, SHANKIJK=0, 0.707, 0.707, ANGLE=0

the demon will assume the last called.....
________
CHEVY-WIKI.COM
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
dph51 over 14 years ago

Maybe use Select Case

c1 = comment/input,no,'Select Probe Rotation : A0B0 - Enter '1'
A45B45 - Enter '2'

SELECT/C1.input
CASE/1
tip/T1A0B0
END_CASE/
CASE/2
tip/T1A45B45
END_CASE/
END_SELECT

Edit as you need to add other tip rotations
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
dph51 over 14 years ago

As Tking says,
If you don's set an initial tip rotation in the program, you will rotate to the last rotation used.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel

overpsp over 14 years ago

i think this resolve my problem

ASSIGN/V1=1
            IF/V1==1
            GOTO/L1
            END_IF/
            IF/V1==0
            GOTO/L2
            END_IF/
END        =LABEL/
            PROGRAM/END
L1         =LABEL/
            TIP/T1A45B180, SHANKIJK=0, -0.707, 0.707, ANGLE=180
            GOTO/END
L2         =LABEL/
            TIP/T1A45B0, SHANKIJK=0, 0.707, 0.707, ANGLE=0
            GOTO/END
L3         =LABEL/
            TIP/T1A45B-180, SHANKIJK=0, -0.707, 0.707, ANGLE=180
            GOTO/END
L4         =LABEL/
            TIP/T1A7.5B-105, SHANKIJK=0.126, -0.034, 0.991, ANGLE=-104.877
            GOTO/END

________
White Girls live