Upside-down Alignment

Hey guys. I'm trying to do an iterative alignment on a fixture but I'm hitting a speed bump and I'm not sure whats causing it. The points for the manual alignment are identical to the automatic alignment and share all the same properties. The manual alignment shows the vector correctly but the probe is upside down. The automatic one shows the vector correctly and the probe in the correct orientation. I've posted the code below as well as attached a picture of the "upside down probe". Does anyone see where the issue lies? When I run it, I go through the manual alignment and then when it attempts to measure the Master tooling ball on its own, it tries to go to the centre of the tooling ball and reads an unexpected probe hit. Running PC-DMIS 3.7 MR3

upside-down probe

STARTUP    =ALIGNMENT/START,RECALL:, LIST= YES
            ALIGNMENT/END
            MODE/MANUAL
            LOADPROBE/2X20_E30
            TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
            FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, , 
            ASSIGN/INPUT_CUSTOMER_P = "xxxxx"
            ASSIGN/JOB_INPUT_P = "xxxx"
            ASSIGN/PART_NAME_INPUT_P = "xxxxxx"
            ASSIGN/PART_NUM_INPUT_P = "xxxxx"
            ASSIGN/TM_INPUT = "xxx"
            ASSIGN/TZ_INPUT = ""
            MOVESPEED/ 75
            TOUCHSPEED/ 1
            PREHIT/ 4
            RETRACT/ 2
MASTER_M   =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-700.08,1262.45,0,0,-1,12.7
            ACTL/372.654,161.77,-483.981,0,0,-1,12.689
            TARG/2299.95,-700.08,1262.45,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 1,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,0,1
LINE_M     =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-175.076,1262.4,0,0,-1,12.7
            ACTL/370.56,686.758,-483.94,0,0,-1,12.69
            TARG/2299.95,-175.076,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,0,1
PLANE_M    =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2549.948,-700.101,1262.4,0,0,-1,12.7
            ACTL/122.679,160.773,-483.972,0,0,-1,12.714
            TARG/2549.948,-700.101,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,0,1
A0         =ALIGNMENT/START,RECALL:STARTUP, LIST= YES
            ALIGNMENT/ITERATE
              PNT TARGET RAD = 0.5, START LABEL = , FIXTURE TOL = 0.12, ERROR LABEL = 
              MEAS ALL FEAT = NO ,MAX ITERATIONS = 99 ,LEVEL AXIS=ZAXIS ,ROTATE AXIS=XAXIS ,ORIGIN AXIS=YAXIS
            LEVEL = MASTER_M,LINE_M,PLANE_M,,
            ROTATE = MASTER_M,LINE_M,,
            ORIGIN = MASTER_M,,
            ALIGNMENT/END
            MODE/DCC
            MOVE/POINT,NORMAL,2371.693,-704.155,1074.34
MASTER     =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-700.08,1262.45,0,0,-1,12.7
            ACTL/2299.95,-700.08,1262.45,0,0,-1,12.7
            TARG/2299.95,-700.08,1262.45,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 1,$
            START ANGLE 1 = 0,END ANGLE 1 = 360,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,0,1
            MOVE/POINT,NORMAL,2300.86,-688.662,999.186
            MOVE/POINT,NORMAL,2203.265,-689.038,999.197
            MOVE/POINT,NORMAL,2201.072,-140.423,999.19
            MOVE/POINT,NORMAL,2345.682,-173.786,1215.66
LINE       =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-175.076,1262.4,0,0,-1,12.7
            ACTL/2299.918,-175.105,1262.406,-0.0000344,0.0000062,-1,12.7
            TARG/2299.95,-175.076,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,0,1
            MOVE/POINT,NORMAL,2349.049,-152.543,929.8
            MOVE/POINT,NORMAL,2453.275,-206.54,929.787
            MOVE/POINT,NORMAL,2559.6,-653.308,929.781
            MOVE/POINT,NORMAL,2580.739,-695.373,1215.982
            MOVE/POINT,NORMAL,2567.678,-716.314,1262.361
PLANE      =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2549.948,-700.101,1262.4,0,0,-1,12.7
            ACTL/2549.915,-700.131,1262.394,-0.0000344,0.0000062,-1,12.7
            TARG/2549.948,-700.101,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,0,1
            MOVE/POINT,NORMAL,2540.867,-687.7,1055.002
A1         =ALIGNMENT/START,RECALL:STARTUP, LIST= YES
            ALIGNMENT/ITERATE
              PNT TARGET RAD = 0.5, START LABEL = , FIXTURE TOL = 0.12, ERROR LABEL = 
              MEAS ALL FEAT = NO ,MAX ITERATIONS = 99 ,LEVEL AXIS=ZAXIS ,ROTATE AXIS=XAXIS ,ORIGIN AXIS=YAXIS
            LEVEL = MASTER,LINE,PLANE,,
            ROTATE = MASTER,LINE,,
            ORIGIN = MASTER,,
            ALIGNMENT/END

Parents

button.monkey over 10 years ago

Thanks for the replies guys. I changed the angle vectors and the MEAS ALL FEAT variables but I'm still having the same issue. The co-ordinates listed by the command box make it look like it's trying to touch the center of the sphere. If that hit gets messed up and I hit continue it will continue taking hits around the diameter, return to the top and then have another bad touch at the top of the probe. It's listing the same Z values for the first hit as the ones around the diameter meaning it's trying to go touch the center the tooling ball instead of the top. The ACTL reading for the z axis is -483.998 and that's where it's trying to touch instead of something around -476.872. All the features are set to out and the tooling ball diameters are the correct sizes.

STARTUP    =ALIGNMENT/START,RECALL:, LIST= YES
            ALIGNMENT/END
            MODE/MANUAL
            LOADPROBE/2X20_E30
            TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
            FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, , 
            ASSIGN/INPUT_CUSTOMER_P = "xxxxx"
            ASSIGN/JOB_INPUT_P = "xxxx"
            ASSIGN/PART_NAME_INPUT_P = "xxxx"
            ASSIGN/PART_NUM_INPUT_P = "xxxx"
            ASSIGN/TM_INPUT = "xxxx"
            ASSIGN/TZ_INPUT = ""
            MOVESPEED/ 75
            TOUCHSPEED/ 1
            PREHIT/ 4
            RETRACT/ 2
MASTER_M   =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-700.08,1262.45,0,0,-1,12.7
            ACTL/383.282,145.929,-483.998,-0.0000604,-0.0000068,1,12.691
            TARG/2299.95,-700.08,1262.45,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 1,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
LINE_M     =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-175.076,1262.4,0,0,-1,12.7
            ACTL/368.083,670.705,-483.946,0,0,-1,12.696
            TARG/2299.95,-175.076,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
PLANE_M    =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2549.948,-700.101,1262.4,0,0,-1,12.7
            ACTL/133.393,138.699,-483.963,0,0,-1,12.687
            TARG/2549.948,-700.101,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
A0         =ALIGNMENT/START,RECALL:STARTUP, LIST= YES
            ALIGNMENT/ITERATE
              PNT TARGET RAD = 0.5, START LABEL = , FIXTURE TOL = 0.12, ERROR LABEL = 
              MEAS ALL FEAT = ONCE ,MAX ITERATIONS = 99 ,LEVEL AXIS=ZAXIS ,ROTATE AXIS=XAXIS ,ORIGIN AXIS=YAXIS
            LEVEL = MASTER_M,LINE_M,PLANE_M,,
            ROTATE = MASTER_M,LINE_M,,
            ORIGIN = MASTER_M,,
            ALIGNMENT/END
            MODE/DCC
            MOVE/POINT,NORMAL,2371.698,-704.151,1074.333
MASTER     =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-700.08,1262.45,0,0,-1,12.7
            ACTL/2299.953,-700.078,1262.452,0.0000111,-0.0000094,-1,12.7
            TARG/2299.95,-700.08,1262.45,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 1,$
            START ANGLE 1 = 0,END ANGLE 1 = 360,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
            MOVE/POINT,NORMAL,2300.868,-688.656,999.177
            MOVE/POINT,NORMAL,2203.272,-689.032,999.185
            MOVE/POINT,NORMAL,2201.082,-140.417,999.187
            MOVE/POINT,NORMAL,2345.684,-173.784,1215.662
LINE       =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-175.076,1262.4,0,0,-1,12.7
            ACTL/2299.952,-175.074,1262.397,0.0000111,-0.0000094,-1,12.7
            TARG/2299.95,-175.076,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
            MOVE/POINT,NORMAL,2349.061,-152.536,929.802
            MOVE/POINT,NORMAL,2453.288,-206.534,929.793
            MOVE/POINT,NORMAL,2559.611,-653.302,929.782
            MOVE/POINT,NORMAL,2580.738,-695.372,1215.983
            MOVE/POINT,NORMAL,2567.676,-716.314,1262.361
PLANE      =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2549.948,-700.101,1262.4,0,0,-1,12.7
            ACTL/2549.951,-700.099,1262.404,0.0000111,-0.0000094,-1,12.7
            TARG/2549.948,-700.101,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
            MOVE/POINT,NORMAL,2540.873,-687.696,1055.002
A1         =ALIGNMENT/START,RECALL:STARTUP, LIST= YES
            ALIGNMENT/ITERATE
              PNT TARGET RAD = 0.5, START LABEL = , FIXTURE TOL = 0.12, ERROR LABEL = 
              MEAS ALL FEAT = ALWAYS ,MAX ITERATIONS = 99 ,LEVEL AXIS=ZAXIS ,ROTATE AXIS=XAXIS ,ORIGIN AXIS=YAXIS
            LEVEL = MASTER,LINE,PLANE,,
            ROTATE = MASTER,LINE,,
            ORIGIN = MASTER,,
            ALIGNMENT/END

Reply

button.monkey over 10 years ago

STARTUP    =ALIGNMENT/START,RECALL:, LIST= YES
            ALIGNMENT/END
            MODE/MANUAL
            LOADPROBE/2X20_E30
            TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
            FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, , 
            ASSIGN/INPUT_CUSTOMER_P = "xxxxx"
            ASSIGN/JOB_INPUT_P = "xxxx"
            ASSIGN/PART_NAME_INPUT_P = "xxxx"
            ASSIGN/PART_NUM_INPUT_P = "xxxx"
            ASSIGN/TM_INPUT = "xxxx"
            ASSIGN/TZ_INPUT = ""
            MOVESPEED/ 75
            TOUCHSPEED/ 1
            PREHIT/ 4
            RETRACT/ 2
MASTER_M   =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-700.08,1262.45,0,0,-1,12.7
            ACTL/383.282,145.929,-483.998,-0.0000604,-0.0000068,1,12.691
            TARG/2299.95,-700.08,1262.45,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 1,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
LINE_M     =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-175.076,1262.4,0,0,-1,12.7
            ACTL/368.083,670.705,-483.946,0,0,-1,12.696
            TARG/2299.95,-175.076,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
PLANE_M    =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2549.948,-700.101,1262.4,0,0,-1,12.7
            ACTL/133.393,138.699,-483.963,0,0,-1,12.687
            TARG/2549.948,-700.101,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 5,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
A0         =ALIGNMENT/START,RECALL:STARTUP, LIST= YES
            ALIGNMENT/ITERATE
              PNT TARGET RAD = 0.5, START LABEL = , FIXTURE TOL = 0.12, ERROR LABEL = 
              MEAS ALL FEAT = ONCE ,MAX ITERATIONS = 99 ,LEVEL AXIS=ZAXIS ,ROTATE AXIS=XAXIS ,ORIGIN AXIS=YAXIS
            LEVEL = MASTER_M,LINE_M,PLANE_M,,
            ROTATE = MASTER_M,LINE_M,,
            ORIGIN = MASTER_M,,
            ALIGNMENT/END
            MODE/DCC
            MOVE/POINT,NORMAL,2371.698,-704.151,1074.333
MASTER     =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-700.08,1262.45,0,0,-1,12.7
            ACTL/2299.953,-700.078,1262.452,0.0000111,-0.0000094,-1,12.7
            TARG/2299.95,-700.08,1262.45,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 1,$
            START ANGLE 1 = 0,END ANGLE 1 = 360,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
            MOVE/POINT,NORMAL,2300.868,-688.656,999.177
            MOVE/POINT,NORMAL,2203.272,-689.032,999.185
            MOVE/POINT,NORMAL,2201.082,-140.417,999.187
            MOVE/POINT,NORMAL,2345.684,-173.784,1215.662
LINE       =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2299.95,-175.076,1262.4,0,0,-1,12.7
            ACTL/2299.952,-175.074,1262.397,0.0000111,-0.0000094,-1,12.7
            TARG/2299.95,-175.076,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
            MOVE/POINT,NORMAL,2349.061,-152.536,929.802
            MOVE/POINT,NORMAL,2453.288,-206.534,929.793
            MOVE/POINT,NORMAL,2559.611,-653.302,929.782
            MOVE/POINT,NORMAL,2580.738,-695.372,1215.983
            MOVE/POINT,NORMAL,2567.676,-716.314,1262.361
PLANE      =AUTO/SPHERE,SHOWALLPARAMS = YES,SHOWHITS = NO
            THEO/2549.948,-700.101,1262.4,0,0,-1,12.7
            ACTL/2549.951,-700.099,1262.404,0.0000111,-0.0000094,-1,12.7
            TARG/2549.948,-700.101,1262.4,0,0,-1
            THEO_THICKNESS = 0,RECT,OUT,$
            AUTO MOVE = BOTH,DISTANCE = 5,$
            NUMHITS = 9,NUMROWS = 2,INIT = 0,PERM = 0,SPACER = 2,$
            START ANGLE 1 = 360,END ANGLE 1 = 0,$
            START ANGLE 2 = 0,END ANGLE 2 = 90,$
            ANGLE VEC = 0,1,0
            MOVE/POINT,NORMAL,2540.873,-687.696,1055.002
A1         =ALIGNMENT/START,RECALL:STARTUP, LIST= YES
            ALIGNMENT/ITERATE
              PNT TARGET RAD = 0.5, START LABEL = , FIXTURE TOL = 0.12, ERROR LABEL = 
              MEAS ALL FEAT = ALWAYS ,MAX ITERATIONS = 99 ,LEVEL AXIS=ZAXIS ,ROTATE AXIS=XAXIS ,ORIGIN AXIS=YAXIS
            LEVEL = MASTER,LINE,PLANE,,
            ROTATE = MASTER,LINE,,
            ORIGIN = MASTER,,
            ALIGNMENT/END

Children

No Data