Is it possible to extract the sample points taken on a diameter (Auto CIR or Auto CYL)? I have to measure the surfaces around some holes on an assembly and the hole locations and would just add more sample points than the standard (3) instead of measuring the diameter and measure a plane.
I think this (^^^) would be the easiest in the long run. However, if you had to extract the sample hits something like this could work...
CYL6 =FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,0>,<0,0,1>,0.5,0.375
ACTL/<0,0,0>,<0,0,1>,0.5,0.375
TARG/<0,0,0>,<0,0,1>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
REPORT VEC=<0.2706061,0.653305,0.707082>
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=6,NUMLEVELS=2,DEPTH=0.2,END OFFSET=1,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=3,SPACER=0.25
AVOIDANCE MOVE=BOTH,DISTANCE=0.375
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
ASSIGN/V1=GETTEXT("SAMPLE_HIT_THEO_X",1,{CYL6})
ASSIGN/V2=GETTEXT("SAMPLE_HIT_THEO_Y",1,{CYL6})
ASSIGN/V3=GETTEXT("SAMPLE_HIT_THEO_Z",1,{CYL6})
ASSIGN/V4=GETTEXT("SAMPLE_HIT_THEO_I",1,{CYL6})
ASSIGN/V5=GETTEXT("SAMPLE_HIT_THEO_J",1,{CYL6})
ASSIGN/V6=GETTEXT("SAMPLE_HIT_THEO_K",1,{CYL6})
ASSIGN/V7=GETTEXT("SAMPLE_HIT_MEAS_X",1,{CYL6})
ASSIGN/V8=GETTEXT("SAMPLE_HIT_MEAS_Y",1,{CYL6})
ASSIGN/V9=GETTEXT("SAMPLE_HIT_MEAS_Z",1,{CYL6})
F1 =GENERIC/POINT,DEPENDENT,CARTESIAN,$
NOM/XYZ,<V1,V2,V3>,$
MEAS/XYZ,<V7,V8,V9>,$
NOM/IJK,<V4,V5,V6>,$
MEAS/IJK,<V4,V5,V6>
DIM LOC1= LOCATION OF POINT F1 UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
X 0.5000 0.0020 -0.0020 0.5000 0.0000 0.0000 ----#----
Y 0.0000 0.0020 -0.0020 0.0000 0.0000 0.0000 ----#----
Z 0.0000 0.0020 -0.0020 0.0000 0.0000 0.0000 ----#----
END OF DIMENSION LOC1
This only gets the first sample hit. You would need to repeat as needed for whatever number of sample hits you have. Just increment the index number ( "1" in this case and immediately before the feature label reference). Seems like a lot of work though.
Here is the Generic Sample Points using GETTEXT("SAMPLE_HIT_THEO_X",1,{CYL6})
I think this (^^^) would be the easiest in the long run. However, if you had to extract the sample hits something like this could work...
CYL6 =FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,0>,<0,0,1>,0.5,0.375
ACTL/<0,0,0>,<0,0,1>,0.5,0.375
TARG/<0,0,0>,<0,0,1>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
REPORT VEC=<0.2706061,0.653305,0.707082>
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=6,NUMLEVELS=2,DEPTH=0.2,END OFFSET=1,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=3,SPACER=0.25
AVOIDANCE MOVE=BOTH,DISTANCE=0.375
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
ASSIGN/V1=GETTEXT("SAMPLE_HIT_THEO_X",1,{CYL6})
ASSIGN/V2=GETTEXT("SAMPLE_HIT_THEO_Y",1,{CYL6})
ASSIGN/V3=GETTEXT("SAMPLE_HIT_THEO_Z",1,{CYL6})
ASSIGN/V4=GETTEXT("SAMPLE_HIT_THEO_I",1,{CYL6})
ASSIGN/V5=GETTEXT("SAMPLE_HIT_THEO_J",1,{CYL6})
ASSIGN/V6=GETTEXT("SAMPLE_HIT_THEO_K",1,{CYL6})
ASSIGN/V7=GETTEXT("SAMPLE_HIT_MEAS_X",1,{CYL6})
ASSIGN/V8=GETTEXT("SAMPLE_HIT_MEAS_Y",1,{CYL6})
ASSIGN/V9=GETTEXT("SAMPLE_HIT_MEAS_Z",1,{CYL6})
F1 =GENERIC/POINT,DEPENDENT,CARTESIAN,$
NOM/XYZ,<V1,V2,V3>,$
MEAS/XYZ,<V7,V8,V9>,$
NOM/IJK,<V4,V5,V6>,$
MEAS/IJK,<V4,V5,V6>
DIM LOC1= LOCATION OF POINT F1 UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
X 0.5000 0.0020 -0.0020 0.5000 0.0000 0.0000 ----#----
Y 0.0000 0.0020 -0.0020 0.0000 0.0000 0.0000 ----#----
Z 0.0000 0.0020 -0.0020 0.0000 0.0000 0.0000 ----#----
END OF DIMENSION LOC1
This only gets the first sample hit. You would need to repeat as needed for whatever number of sample hits you have. Just increment the index number ( "1" in this case and immediately before the feature label reference). Seems like a lot of work though.
Here is the Generic Sample Points using GETTEXT("SAMPLE_HIT_THEO_X",1,{CYL6})
