Hello,
I'm pretty new to PC-DMIS and CMM programming in general. I've been working with it for a few months now. My problem is this. I keep getting an out of stroke error when switching to DCC alignment and I'm not sure what I'm doing wrong. The machine still have several inches of z travel and should have no problem probing the top of the part.
STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
ALIGNMENT/END
MODE/MANUAL
FORMAT/ ,OPTIONS, , , , ;NOM,TOL,MEAS,DEV,OUTTOL, ,
LOADPROBE/CAM1MM
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
CLEARP/ZPLUS,0.1,ZPLUS,0.1,ON
CHECK/0.01,1
PREHIT/0.039
RETRACT/0.039
PLN1 =FEAT/PLANE,CARTESIAN,TRIANGLE
THEO/<0.0455,0.1918,13.431>,<0,0,1>
ACTL/<7.9609,9.8935,-10.6435>,<-0.0000623,0.0000659,1>
MEAS/PLANE,3
MOVE/CLEARPLANE
HIT/BASIC,NORMAL,<-0.0057,-2.0867,13.431>,<0,0,1>,<8.0029,7.5681,-10.6433>,USE THEO=YES
HIT/BASIC,NORMAL,<1.6804,1.2412,13.431>,<0,0,1>,<6.371,11.0562,-10.6436>,USE THEO=YES
HIT/BASIC,NORMAL,<-1.5381,1.4208,13.431>,<0,0,1>,<9.509,11.0562,-10.6434>,USE THEO=YES
ENDMEAS/
A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/END
CIR1 =FEAT/CIRCLE,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,-0.0401>,<0,0,1>,4.04
ACTL/<7.9356,9.6558,-0.0767>,<0,0,1>,4.0419
MEAS/CIRCLE,3,ZPLUS
MOVE/CLEARPLANE
HIT/BASIC,NORMAL,<-1.5024,1.3503,-0.0365>,<0.743762,-0.6684445,0>,<8.0246,7.6368,-0.0768>,USE THEO=YES
HIT/BASIC,NORMAL,<1.6655,1.143,-0.0381>,<-0.824512,-0.5658445,0>,<6.4087,10.9798,-0.0765>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0114,-2.02,-0.0456>,<-0.0056312,0.9999841,0>,<9.4625,10.9797,-0.0767>,USE THEO=YES
ENDMEAS/
A2 =ALIGNMENT/START,RECALL:A1,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/TRANS,XAXIS,CIR1
ALIGNMENT/TRANS,YAXIS,CIR1
ALIGNMENT/END
MODE/DCC
PLN2 =FEAT/PLANE,CARTESIAN,TRIANGLE
THEO/<-0.0044,0.0558,0>,<0,0,1>
ACTL/<-7.9392,-9.6009,24.0743>,<0.0000623,-0.0000659,1>
MEAS/PLANE,9
MOVE/CLEARPLANE
HIT/BASIC,NORMAL,<-0.0042,-2.0978,0>,<0,0,1>,<-7.939,-11.7545,24.0742>,USE THEO=YES
HIT/BASIC,NORMAL,<1.2838,-1.6618,0>,<0,0,1>,<-6.6509,-11.3185,24.0741>,USE THEO=YES
HIT/BASIC,NORMAL,<2.0282,-0.5199,0>,<0,0,1>,<-5.9066,-10.1766,24.0741>,USE THEO=YES
HIT/BASIC,NORMAL,<1.84,0.9982,0>,<0,0,1>,<-6.0948,-8.6585,24.0743>,USE THEO=YES
HIT/BASIC,NORMAL,<0.6224,1.9827,0>,<0,0,1>,<-7.3124,-7.674,24.0744>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.6786,1.9875,0>,<0,0,1>,<-8.6133,-7.6692,24.0745>,USE THEO=YES
HIT/BASIC,NORMAL,<-1.5923,1.3492,0>,<0,0,1>,<-9.5271,-8.3075,24.0745>,USE THEO=YES
HIT/BASIC,NORMAL,<-2.0851,-0.0441,0>,<0,0,1>,<-10.0198,-9.7008,24.0744>,USE THEO=YES
HIT/BASIC,NORMAL,<-1.454,-1.4915,0>,<0,0,1>,<-9.3888,-11.1482,24.0743>,USE THEO=YES
ENDMEAS/
CIR2 =FEAT/CIRCLE,CARTESIAN,OUT,LEAST_SQR
THEO/<0,0,-0.12>,<0,0,1>,4.379,0
ACTL/<-7.9348,-9.6567,24.0039>,<0.0000623,-0.0000659,1>,4.379,0
MEAS/CIRCLE,3,ZPLUS
MOVE/CLEARPLANE
HIT/BASIC,NORMAL,<-1.9022,-1.0842,-0.12>,<-0.8687924,-0.4951766,0>,<-9.837,-10.7409,23.9765>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<1.8427,-1.1825,-0.12>,<0.8416088,-0.5400875,0>,<-6.092,-10.8392,24.0176>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<0.0215,2.1894,-0.12>,<0.0098289,0.9999517,0>,<-7.9132,-7.4673,24.0174>,USE THEO=YES
ENDMEAS/
A3 =ALIGNMENT/START,RECALL:A2,LIST=YES
ALIGNMENT/TRANS,XAXIS,CIR2
ALIGNMENT/TRANS,YAXIS,CIR2
ALIGNMENT/END
