You can now watch all the session recordings here:
What's New in PC-DMIS 2020? - Session 1
What's New in PC-DMIS 2020? - Session 2
Creation: Taking the Pain Out of Routine Creation
Execution: Simplifying the Measurement Process
Reporting: The A-Z of Collaborative Reporting
STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES ALIGNMENT/END MODE/MANUAL MOVESPEED/ 10 SCANSPEED/5 MANRETRACT/0.7874 FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, , OPTIONPROBE/MAXFORCE=0.6,LOWFORCE=0.2,UPPERFORCE=0.6,TRIGGERFO RCE=0.4, PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=7, RETURNSPEED=1,SCANPNTDENSITY=5, SCANACCELERATION=3,SCANOFFSETFORCE=0.03, PROBINGMODE=LFPS,MANFINEPROBING=NO LOADPROBE/1½MMX40DEG TIP/TIP1, SHANKIJK=0.64279, 0, 0.76604, ANGLE=90 UPS1 =Use Parameter Set/LFPS WORKPLANE/XPLUS PLN1 =FEAT/PLANE,CARTESIAN,TRIANGLE THEO/<0,-0.00309,0.41858>,<1,0,0> ACTL/<26.29058,14.97437,8.34265>,<0.999965,0.0022925,-0.0080464> MEAS/PLANE,4 HIT/BASIC,NORMAL,<0,-2.50799,0.08688>,<1,0,0>,<26.29404,12.36114,8.0263 3>,USE THEO=YES HIT/BASIC,NORMAL,<0,-2.59862,0.77035>,<1,0,0>,<26.29892,12.36032,8.6367 2>,USE THEO=YES HIT/BASIC,NORMAL,<0,2.54499,0.73796>,<1,0,0>,<26.28691 ,17.58726,8.62798>,USE THEO=YES HIT/BASIC,NORMAL,<0,2.54923,0.07911>,<1,0,0>,<26.28245 ,17.58876,8.07957>,USE THEO=YES ENDMEAS/ LIN1 =FEAT/LINE,CARTESIAN,UNBOUNDED THEO/<0.14552,-2.32651,0>,<0,1,0> ACTL/<26.43124,12.50052,7.95076>,<0,0.9999784,0.0065727 > MEAS/LINE,2,XPLUS HIT/BASIC,NORMAL,<0.15486,-2.32651,0>,<0,0,1>,<26.43636,12.50052,7.95076>,USE THEO=YES HIT/BASIC,NORMAL,<0.13619,2.50961,0>,<0,0,1>,<26.42612 ,17.21094,7.98172>,USE THEO=YES ENDMEAS/ PNT1 =FEAT/POINT,CARTESIAN THEO/<-0.07941,-2.6875,0.48925>,<0,-1,0> ACTL/<26.27211,12.28246,8.6563>,<0.0133524,-0.9920864,0.1248453> MEAS/POINT,1,WORKPLANE HIT/BASIC,NORMAL,<-0.07941,-2.6875,0.48925>,<0,-1,0>,<26.27211,12.28246,8.6563>,USE THEO=YES ENDMEAS/ A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES ALIGNMENT/LEVEL,XPLUS,PLN1 ALIGNMENT/TRANS,XAXIS,PLN1 ALIGNMENT/ROTATE,YPLUS,TO,LIN1,ABOUT,XPLUS ALIGNMENT/TRANS,ZAXIS,LIN1 ALIGNMENT/TRANS,YAXIS,PNT1 ALIGNMENT/END MODE/DCC CLEARP/XPLUS,1,XPLUS,0,ON MOVE/CLEARPLANE DTMA =FEAT/CONTACT/PLANE/ADAPTIVE_FREE_FORM_PLANE_SCAN,CARTESIAN,OUTLINE,LE AST_SQR THEO/<0,2.68276,0.20274>,<1,0,0> ACTL/<0.00025,2.69069,0.19001>,<1,-0.0000112,0.0000061> TARG/<0,2.68276,0.20274>,<1,0,0> ANGLE VEC=<0,0,-1>,SQUARE SHOW FEATURE PARAMETERS=YES VOID DETECTION=NO SURFACE=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE CIRCULAR MOVES=STRAIGHT GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES NUMHITS=3,NUMROWS=2 SPACER=0.6 AVOIDANCE MOVE=BOTH,DISTANCE=0.2937 SHOW HITS=NO MOVE/CLEARPLANE LIN2 =FEAT/CONTACT/LINE/DEFAULT,CARTESIAN,BOUNDED THEO/<0.257,0.1702,0>,<0.257,5.1228,0>,<0,1,0>,<0,0,1>, <1,0,0>,4.9526 ACTL/<0.257,0.1702,-0.00001>,<0.257,5.12278,-0.00018>,<0,1,-0.0000342>,<0,0.0000342,1>,<1,0,0>,4.95258 TARG/<0.257,0.1702,0>,<0.257,5.1228,0>,<0,1,0>,<0,0,1>, <1,0,0> SHOW FEATURE PARAMETERS=YES VOID DETECTION=NO SURFACE1=THICKNESS_NONE,0 SURFACE2=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES NUMHITS=2,DEPTH=0.05 SAMPLE METHOD=SAMPLE_HITS SAMPLE HITS=0,SPACER=0,INDENT1=0,INDENT2=0 AVOIDANCE MOVE=NO,DISTANCE=0.4 SHOW HITS=NO MOVE/CLEARPLANE PNT2 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN THEO/<-0.055,0,0.41>,<0,-1,0> ACTL/<-0.05501,0.00014,0.41006>,<0,-1,0> TARG/<-0.055,0,0.41>,<0,-1,0> SNAP=NO SHOW FEATURE PARAMETERS=YES SURFACE=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES AVOIDANCE MOVE=NO,DISTANCE=0.2 SHOW HITS=NO MOVE/CLEARPLANE PNT3 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN THEO/<-0.055,5.375,0.41>,<0,1,0> ACTL/<-0.05503,5.37431,0.41>,<0,1,0> TARG/<-0.055,5.375,0.41>,<0,1,0> SNAP=NO SHOW FEATURE PARAMETERS=YES SURFACE=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES AVOIDANCE MOVE=NO,DISTANCE=0.2 SHOW HITS=NO MID_POINT =FEAT/POINT,CARTESIAN,NO THEO/<-0.055,2.6875,0.41>,<0,0,1> ACTL/<-0.05502,2.68723,0.41003>,<0.0001198,0.0000537,1> CONSTR/POINT,MID,PNT2,PNT3 A2 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES ALIGNMENT/LEVEL,XPLUS,DTMA ALIGNMENT/TRANS,XAXIS,DTMA ALIGNMENT/ROTATE,YPLUS,TO,LIN2,ABOUT,XPLUS ALIGNMENT/TRANS,ZAXIS,LIN2 ALIGNMENT/TRANS,YAXIS,MID_POINT ALIGNMENT/END FCFFLAT1 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100, SEGMENT_1,FLATNESS,0.001,TOL_ZONE_MATH=DEFAULT, TEXT=OFF,CADGRAPH=ON,REPORTGRAPH=OFF,MULT=100, MEASURED: DTMA:0.00066, ADD FEATURES/DTMA,, MOVE/CLEARPLANE DTMB =FEAT/CONTACT/PLANE/ADAPTIVE_FREE_FORM_PLANE_SCAN,CARTESIAN,OUTLINE,LE AST_SQR THEO/<0.14379,-0.00221,0>,<0,0,1> ACTL/<0.14285,0.00318,0.00027>,<0.0002146,-0.0000011,1> TARG/<0.14379,-0.00221,0>,<0,0,1> ANGLE VEC=<1,0,0>,SQUARE SHOW FEATURE PARAMETERS=YES VOID DETECTION=NO SURFACE=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE CIRCULAR MOVES=STRAIGHT GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES NUMHITS=3,NUMROWS=2 SPACER=0.6 AVOIDANCE MOVE=BOTH,DISTANCE=0.2937 SHOW HITS=NO FCFFLAT2 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100, SEGMENT_1,FLATNESS,0.001,TOL_ZONE_MATH=DEFAULT, TEXT=OFF,CADGRAPH=ON,REPORTGRAPH=OFF,MULT=100, MEASURED: DTMB:0.00052, ADD FEATURES/DTMB,, OPTIONPROBE/MAXFORCE=0.6,LOWFORCE=0.2,UPPERFORCE=0.6,TRIGGERFO RCE=0.4, PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=7, RETURNSPEED=1,SCANPNTDENSITY=10, SCANACCELERATION=3,SCANOFFSETFORCE=0.03, PROBINGMODE=LFPS,MANFINEPROBING=NO SCANSPEED/2 MOVE/CLEARPLANE OPTIONPROBE/MAXFORCE=0.6,LOWFORCE=0.2,UPPERFORCE=0.6,TRIGGERFO RCE=0.4, PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=7, RETURNSPEED=1,SCANPNTDENSITY=2, SCANACCELERATION=3,SCANOFFSETFORCE=0.03, PROBINGMODE=LFPS,MANFINEPROBING=NO SCAN_1 =GROUP/SHOWALLPARAMS=NO ENDGROUP/ID=SCAN_1 $$ NO, ***************************************** ******************************************* ****************************************** ****************************************** MOVE/CLEARPLANE OPTIONPROBE/MAXFORCE=0.6,LOWFORCE=0.2,UPPERFORCE=0.6,TRIGGERFO RCE=0.4, PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=7, RETURNSPEED=1,SCANPNTDENSITY=2, SCANACCELERATION=3,SCANOFFSETFORCE=0.03, PROBINGMODE=LFPS,MANFINEPROBING=NO SCAN_2 =GROUP/SHOWALLPARAMS=NO ENDGROUP/ID=SCAN_2 WORKPLANE/YPLUS DATDEF/A,FEATURES=DTMA,, DATDEF/B,FEATURES=DTMB,, DATDEF/C,FEATURES=MID_POINT,, SCN3 =FEAT/SET,CARTESIAN THEO/<0.33829,-0.00001,-0.50982>,<0,1,0> ACTL/<0.33915,0,-0.50967>,<0,1,0> CONSTR/SET,BASIC,SCN1,SCN2,, SCN4 =FEAT/SET,CARTESIAN THEO/<0.33829,0,-0.50983>,<0,1,0> ACTL/<0.33915,0,-0.50967>,<0,1,0> CONSTR/SET,FILTER,GAUSSIAN,POLAR,SCN3, FILTER/ON,WIDTH=61,UPR=50,OUTLIER_REMOVAL/ON,3 FCFPROF1 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, DATUM_MATH=LSQ,DISPLAY_COORDS=DRF, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDRE PIERCECAD=YES, SEGMENT_1,PROFILE_SURFACE,0.002,__,__,A,B,__,C,__, TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=10, MEASURED: SCN4:0.00123,0.00041, ADD FEATURES/SCN4,, FCFPROF2 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDRE PIERCECAD=YES, SEGMENT_1,PROFILE_SURFACE,0.002,(U),0.001,__,A,B,_ _,C,__, TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=1000, MEASURED: SCN4:0.00088,-0.00007, ADD FEATURES/SCN4,, FCFPROF3 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDRE PIERCECAD=YES, SEGMENT_1,PROFILE_SURFACE,0.002,(U),0.002,__,A,B,_ _,C,__, TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=1000, MEASURED: SCN4:-0.00012,-0.00107, ADD FEATURES/SCN4,,
STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES ALIGNMENT/END MODE/MANUAL MOVESPEED/ 10 SCANSPEED/5 MANRETRACT/0.7874 FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, , OPTIONPROBE/MAXFORCE=0.6,LOWFORCE=0.2,UPPERFORCE=0.6,TRIGGERFO RCE=0.4, PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=7, RETURNSPEED=1,SCANPNTDENSITY=5, SCANACCELERATION=3,SCANOFFSETFORCE=0.03, PROBINGMODE=LFPS,MANFINEPROBING=NO LOADPROBE/1½MMX40DEG TIP/TIP1, SHANKIJK=0.64279, 0, 0.76604, ANGLE=90 UPS1 =Use Parameter Set/LFPS WORKPLANE/XPLUS PLN1 =FEAT/PLANE,CARTESIAN,TRIANGLE THEO/<0,-0.00309,0.41858>,<1,0,0> ACTL/<26.29058,14.97437,8.34265>,<0.999965,0.0022925,-0.0080464> MEAS/PLANE,4 HIT/BASIC,NORMAL,<0,-2.50799,0.08688>,<1,0,0>,<26.29404,12.36114,8.0263 3>,USE THEO=YES HIT/BASIC,NORMAL,<0,-2.59862,0.77035>,<1,0,0>,<26.29892,12.36032,8.6367 2>,USE THEO=YES HIT/BASIC,NORMAL,<0,2.54499,0.73796>,<1,0,0>,<26.28691 ,17.58726,8.62798>,USE THEO=YES HIT/BASIC,NORMAL,<0,2.54923,0.07911>,<1,0,0>,<26.28245 ,17.58876,8.07957>,USE THEO=YES ENDMEAS/ LIN1 =FEAT/LINE,CARTESIAN,UNBOUNDED THEO/<0.14552,-2.32651,0>,<0,1,0> ACTL/<26.43124,12.50052,7.95076>,<0,0.9999784,0.0065727 > MEAS/LINE,2,XPLUS HIT/BASIC,NORMAL,<0.15486,-2.32651,0>,<0,0,1>,<26.43636,12.50052,7.95076>,USE THEO=YES HIT/BASIC,NORMAL,<0.13619,2.50961,0>,<0,0,1>,<26.42612 ,17.21094,7.98172>,USE THEO=YES ENDMEAS/ PNT1 =FEAT/POINT,CARTESIAN THEO/<-0.07941,-2.6875,0.48925>,<0,-1,0> ACTL/<26.27211,12.28246,8.6563>,<0.0133524,-0.9920864,0.1248453> MEAS/POINT,1,WORKPLANE HIT/BASIC,NORMAL,<-0.07941,-2.6875,0.48925>,<0,-1,0>,<26.27211,12.28246,8.6563>,USE THEO=YES ENDMEAS/ A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES ALIGNMENT/LEVEL,XPLUS,PLN1 ALIGNMENT/TRANS,XAXIS,PLN1 ALIGNMENT/ROTATE,YPLUS,TO,LIN1,ABOUT,XPLUS ALIGNMENT/TRANS,ZAXIS,LIN1 ALIGNMENT/TRANS,YAXIS,PNT1 ALIGNMENT/END MODE/DCC CLEARP/XPLUS,1,XPLUS,0,ON MOVE/CLEARPLANE DTMA =FEAT/CONTACT/PLANE/ADAPTIVE_FREE_FORM_PLANE_SCAN,CARTESIAN,OUTLINE,LE AST_SQR THEO/<0,2.68276,0.20274>,<1,0,0> ACTL/<0.00025,2.69069,0.19001>,<1,-0.0000112,0.0000061> TARG/<0,2.68276,0.20274>,<1,0,0> ANGLE VEC=<0,0,-1>,SQUARE SHOW FEATURE PARAMETERS=YES VOID DETECTION=NO SURFACE=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE CIRCULAR MOVES=STRAIGHT GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES NUMHITS=3,NUMROWS=2 SPACER=0.6 AVOIDANCE MOVE=BOTH,DISTANCE=0.2937 SHOW HITS=NO MOVE/CLEARPLANE LIN2 =FEAT/CONTACT/LINE/DEFAULT,CARTESIAN,BOUNDED THEO/<0.257,0.1702,0>,<0.257,5.1228,0>,<0,1,0>,<0,0,1>, <1,0,0>,4.9526 ACTL/<0.257,0.1702,-0.00001>,<0.257,5.12278,-0.00018>,<0,1,-0.0000342>,<0,0.0000342,1>,<1,0,0>,4.95258 TARG/<0.257,0.1702,0>,<0.257,5.1228,0>,<0,1,0>,<0,0,1>, <1,0,0> SHOW FEATURE PARAMETERS=YES VOID DETECTION=NO SURFACE1=THICKNESS_NONE,0 SURFACE2=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES NUMHITS=2,DEPTH=0.05 SAMPLE METHOD=SAMPLE_HITS SAMPLE HITS=0,SPACER=0,INDENT1=0,INDENT2=0 AVOIDANCE MOVE=NO,DISTANCE=0.4 SHOW HITS=NO MOVE/CLEARPLANE PNT2 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN THEO/<-0.055,0,0.41>,<0,-1,0> ACTL/<-0.05501,0.00014,0.41006>,<0,-1,0> TARG/<-0.055,0,0.41>,<0,-1,0> SNAP=NO SHOW FEATURE PARAMETERS=YES SURFACE=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES AVOIDANCE MOVE=NO,DISTANCE=0.2 SHOW HITS=NO MOVE/CLEARPLANE PNT3 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN THEO/<-0.055,5.375,0.41>,<0,1,0> ACTL/<-0.05503,5.37431,0.41>,<0,1,0> TARG/<-0.055,5.375,0.41>,<0,1,0> SNAP=NO SHOW FEATURE PARAMETERS=YES SURFACE=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES AVOIDANCE MOVE=NO,DISTANCE=0.2 SHOW HITS=NO MID_POINT =FEAT/POINT,CARTESIAN,NO THEO/<-0.055,2.6875,0.41>,<0,0,1> ACTL/<-0.05502,2.68723,0.41003>,<0.0001198,0.0000537,1> CONSTR/POINT,MID,PNT2,PNT3 A2 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES ALIGNMENT/LEVEL,XPLUS,DTMA ALIGNMENT/TRANS,XAXIS,DTMA ALIGNMENT/ROTATE,YPLUS,TO,LIN2,ABOUT,XPLUS ALIGNMENT/TRANS,ZAXIS,LIN2 ALIGNMENT/TRANS,YAXIS,MID_POINT ALIGNMENT/END FCFFLAT1 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100, SEGMENT_1,FLATNESS,0.001,TOL_ZONE_MATH=DEFAULT, TEXT=OFF,CADGRAPH=ON,REPORTGRAPH=OFF,MULT=100, MEASURED: DTMA:0.00066, ADD FEATURES/DTMA,, MOVE/CLEARPLANE DTMB =FEAT/CONTACT/PLANE/ADAPTIVE_FREE_FORM_PLANE_SCAN,CARTESIAN,OUTLINE,LE AST_SQR THEO/<0.14379,-0.00221,0>,<0,0,1> ACTL/<0.14285,0.00318,0.00027>,<0.0002146,-0.0000011,1> TARG/<0.14379,-0.00221,0>,<0,0,1> ANGLE VEC=<1,0,0>,SQUARE SHOW FEATURE PARAMETERS=YES VOID DETECTION=NO SURFACE=THICKNESS_NONE,0 MEASURE MODE=NOMINALS RMEAS=NONE,NONE,NONE CIRCULAR MOVES=STRAIGHT GRAPHICAL ANALYSIS=NO FEATURE LOCATOR=NO,NO,"" SHOW CONTACT PARAMETERS=YES NUMHITS=3,NUMROWS=2 SPACER=0.6 AVOIDANCE MOVE=BOTH,DISTANCE=0.2937 SHOW HITS=NO FCFFLAT2 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100, SEGMENT_1,FLATNESS,0.001,TOL_ZONE_MATH=DEFAULT, TEXT=OFF,CADGRAPH=ON,REPORTGRAPH=OFF,MULT=100, MEASURED: DTMB:0.00052, ADD FEATURES/DTMB,, OPTIONPROBE/MAXFORCE=0.6,LOWFORCE=0.2,UPPERFORCE=0.6,TRIGGERFO RCE=0.4, PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=7, RETURNSPEED=1,SCANPNTDENSITY=10, SCANACCELERATION=3,SCANOFFSETFORCE=0.03, PROBINGMODE=LFPS,MANFINEPROBING=NO SCANSPEED/2 MOVE/CLEARPLANE OPTIONPROBE/MAXFORCE=0.6,LOWFORCE=0.2,UPPERFORCE=0.6,TRIGGERFO RCE=0.4, PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=7, RETURNSPEED=1,SCANPNTDENSITY=2, SCANACCELERATION=3,SCANOFFSETFORCE=0.03, PROBINGMODE=LFPS,MANFINEPROBING=NO SCAN_1 =GROUP/SHOWALLPARAMS=NO ENDGROUP/ID=SCAN_1 $$ NO, ***************************************** ******************************************* ****************************************** ****************************************** MOVE/CLEARPLANE OPTIONPROBE/MAXFORCE=0.6,LOWFORCE=0.2,UPPERFORCE=0.6,TRIGGERFO RCE=0.4, PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=7, RETURNSPEED=1,SCANPNTDENSITY=2, SCANACCELERATION=3,SCANOFFSETFORCE=0.03, PROBINGMODE=LFPS,MANFINEPROBING=NO SCAN_2 =GROUP/SHOWALLPARAMS=NO ENDGROUP/ID=SCAN_2 WORKPLANE/YPLUS DATDEF/A,FEATURES=DTMA,, DATDEF/B,FEATURES=DTMB,, DATDEF/C,FEATURES=MID_POINT,, SCN3 =FEAT/SET,CARTESIAN THEO/<0.33829,-0.00001,-0.50982>,<0,1,0> ACTL/<0.33915,0,-0.50967>,<0,1,0> CONSTR/SET,BASIC,SCN1,SCN2,, SCN4 =FEAT/SET,CARTESIAN THEO/<0.33829,0,-0.50983>,<0,1,0> ACTL/<0.33915,0,-0.50967>,<0,1,0> CONSTR/SET,FILTER,GAUSSIAN,POLAR,SCN3, FILTER/ON,WIDTH=61,UPR=50,OUTLIER_REMOVAL/ON,3 FCFPROF1 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, DATUM_MATH=LSQ,DISPLAY_COORDS=DRF, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDRE PIERCECAD=YES, SEGMENT_1,PROFILE_SURFACE,0.002,__,__,A,B,__,C,__, TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=10, MEASURED: SCN4:0.00123,0.00041, ADD FEATURES/SCN4,, FCFPROF2 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDRE PIERCECAD=YES, SEGMENT_1,PROFILE_SURFACE,0.002,(U),0.001,__,A,B,_ _,C,__, TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=1000, MEASURED: SCN4:0.00088,-0.00007, ADD FEATURES/SCN4,, FCFPROF3 =GEOMETRIC_TOLERANCE/STANDARD=ASME Y14.5,SHOWEXPANDED=YES, DATUM_MATH=DEFAULT,DISPLAY_COORDS=DRF, UNITS=IN,OUTPUT=BOTH,ARROWDENSITY=100,ITERATEANDRE PIERCECAD=YES, SEGMENT_1,PROFILE_SURFACE,0.002,(U),0.002,__,A,B,_ _,C,__, TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=1000, MEASURED: SCN4:-0.00012,-0.00107, ADD FEATURES/SCN4,,
