Hello,
I am having trouble understanding how this TP callout can be out by so much. I attached a pic of what the report looks like and the code is shown below. Does anybody have any ideas? I have tried redoing the alignment but that did not work. The alignment code is also shown below. Datums are -A- is the bottom plane of the part, -B- is a center bore, -D- is another hole (See attached op sheet) Thanks in advance!!
ALIGNMENT:
PNT1 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<0.4439,0.5574,0>,<0,0,1>
ACTL/<0.4438,0.5574,0.0001>,<0,0,1>
TARG/<0.4439,0.5574,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=BOTH,DISTANCE=0.05
SHOW HITS=NO
PNT2 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<0.7184,-0.1333,0>,<0,0,1>
ACTL/<0.7184,-0.1334,-0.0006>,<0,0,1>
TARG/<0.7184,-0.1333,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=BOTH,DISTANCE=0.05
SHOW HITS=NO
PNT3 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-0.618,-0.8045,0>,<0,0,1>
ACTL/<-0.618,-0.8045,0.0005>,<0,0,1>
TARG/<-0.618,-0.8045,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=BOTH,DISTANCE=0.05
SHOW HITS=NO
PNT4 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-1.8625,0.0339,0>,<0,0,1>
ACTL/<-1.8626,0.0339,-0.0004>,<0,0,1>
TARG/<-1.8625,0.0339,0>,<0,0,1>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=BOTH,DISTANCE=0.05
SHOW HITS=NO
PLN3 =FEAT/PLANE,CARTESIAN,OUTLINE,NO,LEAST_SQR
THEO/<-0.3296,-0.0867,0>,<0,0,1>
ACTL/<-0.3296,-0.0867,-0.0001>,<-0.0000196,0.0003458,0.9999999>
CONSTR/PLANE,BF,PNT1,PNT2,PNT3,PNT4,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
CIR3 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,1.9>,<0,0,1>,0.595
ACTL/<0.0001,0.0002,1.9>,<0,0,1>,0.596
TARG/<0,0,1.9>,<0,0,1>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=4,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=BOTH,DISTANCE=0.025
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
CIR4 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0.627,-0.675,0>,<0,0,1>,0.206
ACTL/<0.6273,-0.6754,0>,<0,0,1>,0.2088
TARG/<0.627,-0.675,0>,<0,0,1>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=4,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=BOTH,DISTANCE=0.025
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
LIN2 =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
THEO/<0,0,1.9>,<0.2969364,-0.3196647,-0.8998018>
ACTL/<0.0001,0.0002,1.9>,<0.2969961,-0.3198984,-0.899699>
CONSTR/LINE,BF,3D,CIR3,CIR4,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
DCC_ALIGNMENT=ALIGNMENT/START,RECALL:A1,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN3
ALIGNMENT/TRANS,ZAXIS,PLN3
ALIGNMENT/TRANS,XAXIS,CIR3
ALIGNMENT/TRANS,YAXIS,CIR3
ALIGNMENT/ROTATE,XPLUS,TO,LIN2,ABOUT,ZPLUS
ALIGNMENT/ROTATE_OFFSET,47.111,ABOUT,ZPLUS
ALIGNMENT/END
DATDEF/B,FEATURES=CIR3,,
DATDEF/D,FEATURES=CIR4,,
FEATURE:
CIR7 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0.627,0.425,0>,<0,0,1>,0.228
ACTL/<0.6281,0.4246,0>,<0,0,1>,0.2288
TARG/<0.627,0.425,0>,<0,0,1>
START ANG=0,END ANG=360
ANGLE VEC=<1,0.0000058,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=4,DEPTH=0.05,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=BOTH,DISTANCE=0.025
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
TRUE POSITION:
#40_3 =POSITION : CIR7
FEATCTRLFRAME/SHOWNOMS=NO,SHOWPARAMS=YES,SHOWEXPANDED=YES,
CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=10.00,A RROWDENSITY=100,OUTPUT=BOTH,UNITS=IN,
COMPOSITE=NO,FIT TO DATUMS=YES,DEV PERPEN CENTERLINE=ON,OUTPUT ALIGNMENT=Datum Reference Frame
CUSTOMIZED DRF=NO
STANDARDTYPE=ASME_Y14_5
SIZE TOLERANCES/1,DIAMETER,0.228,0.004,0.004
PRIMARY DIMENSION/POSITION,DIAMETER,0.01,MMC,A,B,MMC,0.595,D,MMC,0.2 06
SECONDARY DIMENSION/,<tol>,<MC>,<dat>,<dat>,<dat>
NOTE/#40_3
