hexagon logo
Register Sign in
  • Replies 10 replies
  • Subscribers 223 subscribers
  • Views 237 views
  • Users 0 members are here
Options
Related

Auto callibration

Stuart_Ward
i know how to input auto calibration in to the start of a program, i also know how to define my parameter set.


is there some script using flow commands after the auto calibration that would enable the program to review the auto calibration results and if they are over a certain standard deviation either stop the program or start the calibration again?

If there is a way, please post the script i would need to use including flow commands.

AUTOCALIBRATE/PROBE, PARAMETER_SET=90's, QUALTOOL_MOVED=NO,
CHECK COLLISION=NO, SHOW_SUMMARY=YES, OVERWRITE_RESULTSFILE=YES
BEGIN AUTOCALIBRATE RESULTS FOR PROBE LEITZ_TIP2BY40 USING SET 90's
END AUTOCALIBRATE RESULTS FOR PROBE LEITZ_TIP2BY40 USING SET 90's

this is a far as i have got
Parents
  • Try this:

    Autoqual happens.

    Feed the NUMBER of your STDDEV into a variable.

    Check the variable to see if it is less than or greater than 0.0002 (or whatever you want).

    If STDDEV is less than 0.0002, QUAL is good which means goto label gets executed, program continues on. If STDDEV is greater than 0.0002, GOTO command is not executed and then it will read the line where the comment complains about the failed calibration.
    Thanks for giving me something fun this afternoon lol 



    STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
ALIGNMENT/END
LOADPROBE/7107_G_4X20
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
DO_QUAL_AGAIN=LABEL/
AUTOCALIBRATE/PROBE, PARAMETER_SET=T1A0B0_MASTER, QUALTOOL_MOVED=YES_DCC,
CHECK COLLISION=NO, SHOW_SUMMARY=NO, OVERWRITE_RESULTSFILE=NO
ASSIGN/STDDEV=PROBEDATA("standarddeviation","T1A0B0")
IF_GOTO/STDDEV<0.0002,GOTO = LABEL_QUAL_FAILURE_SKIP
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,
CMM has failed qualification!

Please clean hardware as well
as qualification sphere.

Click OK to re-try.
Click CANCEL to cancel.
GOTO/DO_QUAL_AGAIN
LABEL_QUAL_FAILURE_SKIP=LABEL/
Reply
  • Try this:

    Autoqual happens.

    Feed the NUMBER of your STDDEV into a variable.

    Check the variable to see if it is less than or greater than 0.0002 (or whatever you want).

    If STDDEV is less than 0.0002, QUAL is good which means goto label gets executed, program continues on. If STDDEV is greater than 0.0002, GOTO command is not executed and then it will read the line where the comment complains about the failed calibration.
    Thanks for giving me something fun this afternoon lol 



    STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
ALIGNMENT/END
LOADPROBE/7107_G_4X20
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
DO_QUAL_AGAIN=LABEL/
AUTOCALIBRATE/PROBE, PARAMETER_SET=T1A0B0_MASTER, QUALTOOL_MOVED=YES_DCC,
CHECK COLLISION=NO, SHOW_SUMMARY=NO, OVERWRITE_RESULTSFILE=NO
ASSIGN/STDDEV=PROBEDATA("standarddeviation","T1A0B0")
IF_GOTO/STDDEV<0.0002,GOTO = LABEL_QUAL_FAILURE_SKIP
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,
CMM has failed qualification!

Please clean hardware as well
as qualification sphere.

Click OK to re-try.
Click CANCEL to cancel.
GOTO/DO_QUAL_AGAIN
LABEL_QUAL_FAILURE_SKIP=LABEL/
Children
No Data
© 2024 Hexagon AB and/or its subsidiaries. Privacy Policy | Cloud Services Agreement