Loaded CAD to verify nominals were correct, still no go. Recreating the FCF doesn't change anything either.
Program:
START =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES ALIGNMENT/END MODE/MANUAL CHECK/3,1 FORMAT/TEXT,OPTIONS,ID,HEADINGS,SYMBOLS, ;MEAS,NOM,TOL,DEV,OUTTOL, , LOADPROBE/3MM TIP/TIP1, SHANKIJK=0, 0, 1, ANGLE=0 COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO, Mät ytterdiameter på vänster rörände OBS! Börja med tre stödpunkter! Ø22 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR THEO/<0,0,0>,<0,0,1>,22,0 ACTL/<627.234,644.389,262.38>,<0.2742149,0.1856828,0.94 3572>,21.968,0 TARG/<0,0,0>,<0,0,1> START ANG=0,END ANG=360 ANGLE VEC=<1,0,0> DIRECTION=CCW SHOW FEATURE PARAMETERS=NO SHOW CONTACT PARAMETERS=NO PKT Ø22 =FEAT/POINT,CARTESIAN,NO THEO/<0,0,0>,<0,0,1> ACTL/<627.234,644.389,262.38>,<0.2742149,0.1856828,0.94 3572> CONSTR/POINT,CAST,Ø22 DATDEF/B,FEATURES=Ø22,, A1 =ALIGNMENT/START,RECALL:START,LIST=YES ALIGNMENT/TRANS,XAXIS,PKT Ø22 ALIGNMENT/TRANS,YAXIS,PKT Ø22 ALIGNMENT/TRANS,ZAXIS,PKT Ø22 ALIGNMENT/END COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO, Mät spår i konsol OBS! Börja med tre stödpunkter! SPÅR =FEAT/CONTACT/ROUND SLOT/DEFAULT,CARTESIAN,IN THEO/<295.6,-104.3,-147.2>,<-0.0605674,0.5000144,0.8638965>,<0.997564,0.0003141 ,0.069757>,9,11.8 ACTL/<-245.688,-241.238,-30.76>,<0.7142378,0.0169459,0.6996979>,<0.3198843, 0.8812814,-0.3478752>,9.169,13.982 TARG/<295.6,-104.3,-147.2>,<-0.0605674,0.5000144,0.8638965>,<0.997564,0.0003141 ,0.069757> MEAS ANGLE=160 SHOW FEATURE PARAMETERS=NO SHOW CONTACT PARAMETERS=NO PKT Q =FEAT/POINT,CARTESIAN,YES THEO/<295.6,-104.3,-147.2>,<-0.0605674,0.5000144,0.8638965> ACTL/<-245.688,-241.238,-30.76>,<0.7142378,0.0169459,0.6996979> CONSTR/POINT,CAST,SPÅR A2 =ALIGNMENT/START,RECALL:A1,LIST=YES ALIGNMENT/BF2D,ZPLUS,LEAST_SQR,CREATE WEIGHTS=NO,ROTANDTRANS,USE SCALING=NO,0,0,0,26.844 ITERATEANDREPIERCECAD=NO Deviation Threshold=5,Pause Execution=NO SHOWALLINPUTS=NO,SHOWALLPARAMS=NO ALIGNMENT/END WORKPLANE/YPLUS A3 =ALIGNMENT/START,RECALL:A2,LIST=YES ALIGNMENT/BF2D,YPLUS,LEAST_SQR,CREATE WEIGHTS=NO,ROTANDTRANS,USE SCALING=NO,0,0,0,21.172 ITERATEANDREPIERCECAD=NO Deviation Threshold=5,Pause Execution=NO SHOWALLINPUTS=NO,SHOWALLPARAMS=NO ALIGNMENT/END WORKPLANE/ZPLUS COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO, Mät ytterdiameter på höger rörände OBS! Börja med tre stödpunkter! HÖ RÖRÄNDE =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR THEO/<253,-142.5,-171.7>,<-0.2686794,-0.9630455,-0.0188342>,18,0 ACTL/<-285.276,-50.326,-175.445>,<-0.4032534,0.9128111,-0.0645188>,18.067,0 TARG/<253,-142.5,-171.7>,<-0.2686794,-0.9630455,-0.0188342> START ANG=0,END ANG=360 ANGLE VEC=<-0.0699277,0,0.9975521> DIRECTION=CCW SHOW FEATURE PARAMETERS=NO SHOW CONTACT PARAMETERS=NO COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO, Mät ytterdiameter på Ø16 OBS! Börja med tre stödpunkter! Ø16 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR THEO/<142.3,56.6,-226.6>,<0.4444073,0.8166771,-0.3681585>,16,0 ACTL/<-74.943,-141.655,-220.667>,<0.1179681,-0.9436953,-0.3090674>,16.024,0 TARG/<142.3,56.6,-226.6>,<0.4444073,0.8166771,-0.3681585> START ANG=0,END ANG=360 ANGLE VEC=<-0.6379514,0,-0.7700766> DIRECTION=CCW SHOW FEATURE PARAMETERS=NO SHOW CONTACT PARAMETERS=NO WORKPLANE/ZPLUS A4 =ALIGNMENT/START,RECALL:A3,LIST=YES ALIGNMENT/BF3D,LEAST_SQR,CREATE WEIGHTS=NO,ROTANDTRANS,USE SCALING=NO,-1.755,3.229,-0.217,-141.985,175.886,-1.101 ITERATEANDREPIERCECAD=NO Deviation Threshold=5,Pause Execution=NO SHOWALLINPUTS=NO,SHOWALLPARAMS=NO ALIGNMENT/END REF A =FEAT/PLANE,CARTESIAN,TRIANGLE,NO THEO/<0,0,0>,<0,0,1> ACTL/<0,0,0>,<0,0,1> CONSTR/PLANE,ALIGN,ZPLUS DATDEF/A,FEATURES=REF A,, REF C =FEAT/PLANE,CARTESIAN,TRIANGLE,NO THEO/<0,0,0>,<0,1,0> ACTL/<0,0,0>,<0,1,0> CONSTR/PLANE,ALIGN,YPLUS DATDEF/C,FEATURES=REF C,, DIM DIM3= LOCATION OF CIRCLE Ø22 UNITS=MM ,$ GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=NONE HALF ANGLE=NO AX MEAS NOMINAL +TOL -TOL DEV OUTTOL X 0.610 0.000 0.000 0.000 0.610 0.610 -> Y 3.631 0.000 0.000 0.000 3.631 3.631 -> Z 0.000 0.000 0.000 0.000 0.000 0.000 -> END OF DIMENSION DIM3 DIM DIM2= LOCATION OF POINT PKT Q UNITS=MM ,$ GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=NONE HALF ANGLE=NO AX MEAS NOMINAL +TOL -TOL DEV OUTTOL X 294.187 295.600 0.000 0.000 -1.413 -1.413 <- Y -104.300 -104.300 0.000 0.000 0.000 0.000 -> Z -147.200 -147.200 0.000 0.000 0.000 0.000 -> END OF DIMENSION DIM2 COMMENT/REPT, Mått 295.6 (±2) DIM DIM4= LOCATION OF SLOT SPÅR UNITS=MM ,$ GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO AX MEAS NOMINAL +TOL -TOL DEV OUTTOL X 294.187 295.600 2.000 -2.000 -1.413 0.000 #- END OF DIMENSION DIM4 COMMENT/REPT, Lägeriktighet inom Ø2(M) rel. A/C för Ø22 FCFDIM1 =GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=NO, SIZE/NOMINAL=22,TOLERANCE SPECIFICATION MODE=NOMINAL_WITH_DEVIATIONS, UPPER TOLERANCE=0.15,LOWER TOLERANCE=-0.15, SEGMENT_1,POSITION,DIAMETER,2,MMC,A,C,<dat>, ADD FEATURES/Ø22,, COMMENT/REPT, Lägeriktighet inom Ø4(M) rel. A/C för Ø16 FCFDIM2 =GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=NO, SIZE/NOMINAL=16,TOLERANCE SPECIFICATION MODE=NOMINAL_WITH_DEVIATIONS, UPPER TOLERANCE=0.1,LOWER TOLERANCE=-0.1, SEGMENT_1,POSITION,DIAMETER,4,MMC,A,C,<dat>, ADD FEATURES/Ø16,, COMMENT/REPT, Lägeriktighet inom Ø4(M) rel. A/C för Ø18 FCFDIM3 =GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=NO, SIZE/NOMINAL=18,TOLERANCE SPECIFICATION MODE=NOMINAL_WITH_DEVIATIONS, UPPER TOLERANCE=0.1,LOWER TOLERANCE=-0.1, SEGMENT_1,POSITION,DIAMETER,4,MMC,A,C,<dat>, ADD FEATURES/HÖ RÖRÄNDE,,
Ping neil.challinor
Rob Jensen
