TP of open slot

I came across a print requirement too inspect TP of an open slot on a circular disk as shown in image attached.
what would be the correct way to inspect this?

Parents

jigars over 2 years ago

This is how I have done it for now

MOVE/CLEARPLANE
CIR_LH =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<-0.53,22.305,8.88>,<0,0,1>,0.75
ACTL/<-0.53,22.305,8.88>,<0,0,1>,0.75
TARG/<-0.53,22.305,8.88>,<0,0,1>
START ANG=238,END ANG=270
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO

DIM LOC19= LOCATION OF CIRCLE CIR_LH UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
R 0.3750 0.0160 0.0160 0.3750 0.0000 0.0000 ----#----
END OF DIMENSION LOC19

CIR_RH =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0.53,22.305,8.88>,<0,0,1>,0.75
ACTL/<0.53,22.305,8.88>,<0,0,1>,0.75
TARG/<0.53,22.305,8.88>,<0,0,1>
START ANG=122,END ANG=90
ANGLE VEC=<-1,0,0>
DIRECTION=CW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO

DIM LOC20= LOCATION OF CIRCLE CIR_RH UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
R 0.3750 0.0160 0.0160 0.3750 0.0000 0.0000 ----#----
END OF DIMENSION LOC20

ASSIGN/VLH=LOC19.R.MEAS
ASSIGN/VRH=LOC20.R.MEAS
ASSIGN/VSM=VLH+VRH
ASSIGN/VAV=VSM/2

S1_MID =FEAT/POINT,CARTESIAN,NO
THEO/<0,22.305,8.88>,<0,0,1>
ACTL/<0,22.305,8.88>,<0,0,1>
CONSTR/POINT,MID,CIR_LH,CIR_RH

DIM DIST67= 2D DISTANCE FROM CIRCLE CIR_LH TO CIRCLE CIR_RH (CENTER TO CENTER),NO_RADIUS UNITS=IN,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=NONE
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
M 1.0600 0.0050 0.0050 1.0600 0.0000 0.0000 ----#----

F2 =GENERIC/ROUND_SLOT,DEPENDENT,CARTESIAN,OUT,$
NOM/XYZ,<0,22.305,8.88>,$
MEAS/XYZ,<0,22.305,8.88>,$
NOM/IJK,<0,0,1>,$
MEAS/IJK,<0,0,1>,$
NOM/IJK2,<1,0,0>,$
MEAS/IJK2,<1,0,0>,$
RADIUS/0.375,VAV,$
DISTANCE/1.06,DIST67.M.MEAS

DIM LOC21= POSITION OF SLOT F2 UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH FIT TO DATUMS=OFF DEV PERPEN CENTERLINE=OFF DISPLAY=DIAMETER
AX NOMINAL +TOL -TOL BONUS MEAS DEV OUTTOL
X 0.0000 0.0000 0.0000
LF 1.0600 0.0150 0.0150 0.0150 1.0600 0.0000 0.0000 ----#----
WF 0.7500 0.0320 0.0320 0.0320 0.7500 0.0000 0.0000 ----#----
TP MMC 0.1250 0.0150 0.0000 0.0000 0.0000 #--------
END OF DIMENSION LOC21

Reply

jigars over 2 years ago

This is how I have done it for now

MOVE/CLEARPLANE
CIR_LH =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<-0.53,22.305,8.88>,<0,0,1>,0.75
ACTL/<-0.53,22.305,8.88>,<0,0,1>,0.75
TARG/<-0.53,22.305,8.88>,<0,0,1>
START ANG=238,END ANG=270
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO

DIM LOC19= LOCATION OF CIRCLE CIR_LH UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
R 0.3750 0.0160 0.0160 0.3750 0.0000 0.0000 ----#----
END OF DIMENSION LOC19

CIR_RH =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0.53,22.305,8.88>,<0,0,1>,0.75
ACTL/<0.53,22.305,8.88>,<0,0,1>,0.75
TARG/<0.53,22.305,8.88>,<0,0,1>
START ANG=122,END ANG=90
ANGLE VEC=<-1,0,0>
DIRECTION=CW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO

DIM LOC20= LOCATION OF CIRCLE CIR_RH UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
R 0.3750 0.0160 0.0160 0.3750 0.0000 0.0000 ----#----
END OF DIMENSION LOC20

ASSIGN/VLH=LOC19.R.MEAS
ASSIGN/VRH=LOC20.R.MEAS
ASSIGN/VSM=VLH+VRH
ASSIGN/VAV=VSM/2

S1_MID =FEAT/POINT,CARTESIAN,NO
THEO/<0,22.305,8.88>,<0,0,1>
ACTL/<0,22.305,8.88>,<0,0,1>
CONSTR/POINT,MID,CIR_LH,CIR_RH

DIM DIST67= 2D DISTANCE FROM CIRCLE CIR_LH TO CIRCLE CIR_RH (CENTER TO CENTER),NO_RADIUS UNITS=IN,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=NONE
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
M 1.0600 0.0050 0.0050 1.0600 0.0000 0.0000 ----#----

F2 =GENERIC/ROUND_SLOT,DEPENDENT,CARTESIAN,OUT,$
NOM/XYZ,<0,22.305,8.88>,$
MEAS/XYZ,<0,22.305,8.88>,$
NOM/IJK,<0,0,1>,$
MEAS/IJK,<0,0,1>,$
NOM/IJK2,<1,0,0>,$
MEAS/IJK2,<1,0,0>,$
RADIUS/0.375,VAV,$
DISTANCE/1.06,DIST67.M.MEAS

DIM LOC21= POSITION OF SLOT F2 UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH FIT TO DATUMS=OFF DEV PERPEN CENTERLINE=OFF DISPLAY=DIAMETER
AX NOMINAL +TOL -TOL BONUS MEAS DEV OUTTOL
X 0.0000 0.0000 0.0000
LF 1.0600 0.0150 0.0150 0.0150 1.0600 0.0000 0.0000 ----#----
WF 0.7500 0.0320 0.0320 0.0320 0.7500 0.0000 0.0000 ----#----
TP MMC 0.1250 0.0150 0.0000 0.0000 0.0000 #--------
END OF DIMENSION LOC21

Children

No Data