Masking datum position in xact measure V2016

BKulpa over 2 years ago

I don't want the datum position to show on the report confusing the operators.
How do I turn it off?

Attached Files

Parents

BKulpa over 2 years ago

I guess I'm going back to legacy.
Here's the code.

DATUM_AD_AL=ALIGNMENT/START,RECALL[emoticon:6D505171FAA4497C85C5CA27290C555D]ATUM_TUV_AL1,LIST=YES
              ALIGNMENT/LEVEL,YMINUS,DATUM_A_PLN2
              ALIGNMENT/ROTATE,ZPLUS,TO,PISTON_CYL,ABOUT,YMINUS
              ALIGNMENT/TRANS,XAXIS,PISTON_CYL
              ALIGNMENT/TRANS,YAXIS,DATUM_A_PLN2
            ALIGNMENT/END
D11_12_TOP =POSITION : RACK_TOP_CIR
            FEATCTRLFRAME/SHOWNOMS=YES,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=5.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=MM
            COMPOSITE=NO,FIT TO DATUMS=YES,DEV PERPEN CENTERLINE=ON,OUTPUT ALIGNMENT=Current Alignment
            CUSTOMIZED DRF=NO
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,5.64,0.03,0.03
              PRIMARY DIMENSION/POSITION,DIAMETER,0.35,MMC,A,D,MMC,<size>,<dat>
              SECONDARY DIMENSION/<Dim>,<tol>,MMC,<dat>,<dat>,<dat>
              NOTE/D11_12_TOP
            FEATURES/RACK_TOP_CIR,,
            RACK_TOP_CIR
             X:NOM=13.3
             Y:NOM=11.37
            <NEW>
            DIMINFO/D11_12_TOP;ICON,DIMID,FEATID,VERT,HORIZ, ,$
                    HEADINGS,GRAPH AXIS;MEAS, , , , , , , ,

Reply

BKulpa over 2 years ago

I guess I'm going back to legacy.
Here's the code.

DATUM_AD_AL=ALIGNMENT/START,RECALL[emoticon:6D505171FAA4497C85C5CA27290C555D]ATUM_TUV_AL1,LIST=YES
              ALIGNMENT/LEVEL,YMINUS,DATUM_A_PLN2
              ALIGNMENT/ROTATE,ZPLUS,TO,PISTON_CYL,ABOUT,YMINUS
              ALIGNMENT/TRANS,XAXIS,PISTON_CYL
              ALIGNMENT/TRANS,YAXIS,DATUM_A_PLN2
            ALIGNMENT/END
D11_12_TOP =POSITION : RACK_TOP_CIR
            FEATCTRLFRAME/SHOWNOMS=YES,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=5.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=MM
            COMPOSITE=NO,FIT TO DATUMS=YES,DEV PERPEN CENTERLINE=ON,OUTPUT ALIGNMENT=Current Alignment
            CUSTOMIZED DRF=NO
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,5.64,0.03,0.03
              PRIMARY DIMENSION/POSITION,DIAMETER,0.35,MMC,A,D,MMC,<size>,<dat>
              SECONDARY DIMENSION/<Dim>,<tol>,MMC,<dat>,<dat>,<dat>
              NOTE/D11_12_TOP
            FEATURES/RACK_TOP_CIR,,
            RACK_TOP_CIR
             X:NOM=13.3
             Y:NOM=11.37
            <NEW>
            DIMINFO/D11_12_TOP;ICON,DIMID,FEATID,VERT,HORIZ, ,$
                    HEADINGS,GRAPH AXIS;MEAS, , , , , , , ,

Children

JacobCheverie over 2 years ago in reply to BKulpa

The +TOL column on datum feature D is 0, implying you have no geometric control on D with respect to A. You need to place it above D11_12_TOP position for it to compute properly. Do you have the control located properly in the edit window?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel