Coordinate System Control for Loops.

I am looking for guidance on how coordinate systems interact with loops. I can get stuff to work but often when I make a change inside the loop my Theoretical positions don't work correctly. As well as looking at Theoretical positions that are not correct for the current zero position but the loop works fine.
At end of each loop I recall starting coordinate system. Not sure if this is correct.

Parents

Peter Martignacco 11 months ago

STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
ALIGNMENT/END
MODE/MANUAL
PREHIT/2
RETRACT/2
MOVESPEED/ 100
TOUCHSPEED/ 3
FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, ,
LOADPROBE/1X40MM
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
PNT1 =FEAT/POINT,CARTESIAN
THEO/<570.1171,153.5164,-731.077>,<1,0,0>
ACTL/<-75.6456,460.7623,-717.6337>,<0.9895437,-0.0323887,0.1405496>
MEAS/POINT,1,WORKPLANE
HIT/BASIC,NORMAL,<570.1171,153.5164,-731.077>,<1,0,0>,<-75.6456,460.7623,-717.6337>,USE THEO=YES
ENDMEAS/
A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/TRANS,XAXIS,PNT1
ALIGNMENT/END
WORKPLANE/XPLUS
CIR1 =FEAT/CIRCLE,CARTESIAN,OUT,LEAST_SQR
THEO/<-104.1807,145.9742,-742.0302>,<1,0,0>,29.7556,0
ACTL/<-102.7582,472.244,-724.5375>,<1,0,0>,29.8352,0
MEAS/CIRCLE,7,XPLUS
HIT/BASIC,NORMAL,<-104.1849,143.6979,-727.3293>,<0,-0.153019,0.9882232>,<-102.7593,469.4952,-709.8751>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1723,148.3305,-727.338>,<0,0.1583589,0.9873816>,<-102.7572,470.8276,-709.6889>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1802,150.7639,-727.9391>,<0,0.3218289,0.9467979>,<-102.7572,472.4335,-709.6197>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1731,153.0946,-728.9702>,<0,0.4786854,0.8779865>,<-102.7572,473.9388,-709.714>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1702,148.9579,-727.4569>,<0,0.2005802,0.9796773>,<-102.7602,475.3378,-709.9455>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1914,143.6144,-727.343>,<0,-0.1586376,0.9873369>,<-102.7574,476.4778,-710.2349>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1928,140.3079,-728.2714>,<0,-0.3808012,0.9246569>,<-102.759,479.9376,-711.7562>,USE THEO=YES
ENDMEAS/
A2 =ALIGNMENT/START,RECALL:A1,LIST=YES
ALIGNMENT/TRANS,YAXIS,CIR1
ALIGNMENT/TRANS,ZAXIS,CIR1
ALIGNMENT/END
SAVE/ALIGNMENT,ClamTop2.aln,BOTH
RECALL/ALIGNMENT,EXTERNAL,CLAMTOP2
SAVE/ALIGNMENT,Loop Alignment.aln,BOTH
SAVE/ALIGNMENT,Loop1 Alignment.aln,BOTH
SAVE/ALIGNMENT,Loop2 Alignment.aln,BOTH
MODE/DCC
ASSIGN/LP1=5
ASSIGN/LP2=3
MOVE/POINT,NORMAL,<-265,0,374.756>
C1 =COMMENT/INPUT,NO,FULL SCREEN=YES,
Enter Operator Name
C2 =COMMENT/INPUT,NO,FULL SCREEN=YES,
Enter Batch Number
C3 =COMMENT/INPUT,NO,FULL SCREEN=YES,
Enter Cavity Number
C4 =COMMENT/INPUT,NO,FULL SCREEN=YES,
Enter part count
ASSIGN/V1=C1.INPUT
ASSIGN/V2=C2.INPUT
ASSIGN/V3=C3.INPUT
ASSIGN/V4=C4.INPUT
ASSIGN/LPP1=0
ASSIGN/LPP2=0
WHILE/LPP1<LP1
RECALL/ALIGNMENT,EXTERNAL,LOOP1 ALIGNMENT
COMMENT/REPT,
V1
COMMENT/REPT,
V2
COMMENT/REPT,
V3
COMMENT/REPT,
V4
CHECK/5,1
ONERROR/PROBE_MISS,GOTO L1
TOUCHSPEED/ 2
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,
Please Edit Comment Text!
MOVE/POINT,NORMAL,<-108.3765,-9.8301,47.302>
PNT43 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-109.1368,-9.6043>,<0,-0.9998477,0.0174524>
ACTL/<-109.1368,-74,10.6043>,<0,-0.9998477,0.0174524>
TARG/<-109.1368,-9.6043>,<0,-0.9998477,0.0174524>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO
A12 =ALIGNMENT/START,RECALL:A2,LIST=YES
ALIGNMENT/TRANS,YAXIS,PNT43
ALIGNMENT/TRANS_OFFSET,YAXIS,6.675
ALIGNMENT/END
MOVE/POINT,NORMAL,<-107.2781,-8,43.7868>
CIR3 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
THEO/<-96.5,-0.0001,0>,<-1,0,0>,30,0
ACTL/<-96.5,-0.2775,-0.1342>,<-1,0,0>,29.8378,0
TARG/<-96.5,-0.0001,0>,<-1,0,0>
START ANG=-30,END ANG=40
ANGLE VEC=<0,0,1>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO
MOVE/POINT,NORMAL,<-96.4998,8.2161,45.4023>
MOVE/POINT,NORMAL,<6.3529,-10.5765,43.7869>
PNT375 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-0.0021,-12,5.6195>,<0.9998477,-0.0160941,0.0067502>
ACTL/<0.5302,-12.0119,5.6243>,<0.9998477,-0.0160941,0.0067502>
TARG/<-0.0021,-12,5.6195>,<0.9998477,-0.0160941,0.0067502>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO
A13 =ALIGNMENT/START,RECALL:A12,LIST=YES
ALIGNMENT/TRANS,XAXIS,PNT375
ALIGNMENT/END
MOVE/POINT,NORMAL,<2.2456,-12.0401,44.8521>
PNT2 =FEAT/POINT,CARTESIAN,NO
THEO/<-96.4979,-0.0001,20>,<-1,0,0>
ACTL/<-97.0302,-0.2775,19.8658>,<-1,0,0>
CONSTR/POINT,OFFSET,CIR3,0,0,20
LIN1 =FEAT/LINE,CARTESIAN,UNBOUNDED,YES
THEO/<-96.5,-0.0001,0>,<0,0,-1>
ACTL/<-97.0302,-0.2775,19.8658>,<0,0,-1>
CONSTR/LINE,BF,2D,CIR3,PNT2,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
PNT3 =FEAT/POINT,CARTESIAN,NO
THEO/<-96.5,-0.0001,15>,<0,0,-1>
ACTL/<-97.0302,-0.2775,14.7847>,<0,0,-1>
CONSTR/POINT,PIERCE,CIR3,LIN1
A3 =ALIGNMENT/START,RECALL:A13,LIST=YES
ALIGNMENT/TRANS,ZAXIS,PNT3
ALIGNMENT/END
MOVE/POINT,NORMAL,<6.2052,-6.7966,22.2595>
WORKPLANE/YPLUS
PNT4 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<0.0023,11.2164,-6.1679>,<0.9998477,0.0137117,0.010797>
ACTL/<-0.1159,11.2107,-6.1689>,<0.9998477,0.0137117,0.010797>
TARG/<0.0023,11.2164,-6.1679>,<0.9998477,0.0137117,0.010797>
SNAP=NO
SHOW FEATURE PARAMETERS=YES
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
AUTO WRIST=YES
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
PNT5 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<0.0007,4.4412,-1.3383>,<0.9998477,0.0053955,0.0165974>
ACTL/<-0.0992,4.437,-1.3381>,<0.9998477,0.0053955,0.0165974>
TARG/<0.0007,4.4412,-1.3383>,<0.9998477,0.0053955,0.0165974>
SNAP=NO
SHOW FEATURE PARAMETERS=YES
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
AUTO WRIST=YES
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
--------------------------------------------------------------


DIM DIM-7= 2D DISTANCE FROM LINE LIN52 TO LINE LIN49 PAR TO ZAXIS,NO_RADIUS UNITS=MM,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
M 0.9000 0.0500 0.0500 0.9235 0.0235 0.0000 ------#--
MOVE/POINT,NORMAL,<-1.2795,-0.5035,44.5362>
MOVE/POINT,NORMAL,<-250,0,303.4691>
LOADPROBE/1X40MM
TIP/T1A0B0, SHANKIJK=0.003, -0.0136, 0.9999, ANGLE=89.1929
MOVE/POINT,NORMAL,<-300.7658,0,363.0783>
PRINT/REPORT,EXEC MODE=END,$
TO_FILE=ON,AUTO=537,AUTO OPEN=ON,$
TO_PRINTER=OFF,COPIES=1,$
TO_DMIS_REPORT=OFF,FILE_OPTION=INDEX,FILENAME=,$
REPORT_THEORETICALS=NONE,REPORT_FEATURE_WITH_DIMEN SIONS=NO,$
TO_EXCEL=ON,APPEND,FILENAME=\\MAPAPP72\Mitutoyo\He xagon CMM\Programs\Loader Final Programs\DATA\Clam Top-2.CSV,AUTO OPEN=OFF,$
PREVIOUS_RUNS=DELETE_INSTANCES
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,
Please Edit Comment Text!
GOTO/L2
L1 =LABEL/
MOVE/INCREMENT,<0,0,20>
L2 =LABEL/
ASSIGN/V4=V4+1
TRANSALIGN =ALIGNMENT/START,RECALL:LOOP1 ALIGNMENT,LIST=YES
ALIGNMENT/TRANS_OFFSET,YAXIS,-65
ALIGNMENT/END
SAVE/ALIGNMENT,Loop1 Alignment.aln,BOTH
ASSIGN/LP1=LP1+1
END_WHILE/

Reply

Peter Martignacco 11 months ago

STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
ALIGNMENT/END
MODE/MANUAL
PREHIT/2
RETRACT/2
MOVESPEED/ 100
TOUCHSPEED/ 3
FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, ,
LOADPROBE/1X40MM
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
PNT1 =FEAT/POINT,CARTESIAN
THEO/<570.1171,153.5164,-731.077>,<1,0,0>
ACTL/<-75.6456,460.7623,-717.6337>,<0.9895437,-0.0323887,0.1405496>
MEAS/POINT,1,WORKPLANE
HIT/BASIC,NORMAL,<570.1171,153.5164,-731.077>,<1,0,0>,<-75.6456,460.7623,-717.6337>,USE THEO=YES
ENDMEAS/
A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/TRANS,XAXIS,PNT1
ALIGNMENT/END
WORKPLANE/XPLUS
CIR1 =FEAT/CIRCLE,CARTESIAN,OUT,LEAST_SQR
THEO/<-104.1807,145.9742,-742.0302>,<1,0,0>,29.7556,0
ACTL/<-102.7582,472.244,-724.5375>,<1,0,0>,29.8352,0
MEAS/CIRCLE,7,XPLUS
HIT/BASIC,NORMAL,<-104.1849,143.6979,-727.3293>,<0,-0.153019,0.9882232>,<-102.7593,469.4952,-709.8751>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1723,148.3305,-727.338>,<0,0.1583589,0.9873816>,<-102.7572,470.8276,-709.6889>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1802,150.7639,-727.9391>,<0,0.3218289,0.9467979>,<-102.7572,472.4335,-709.6197>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1731,153.0946,-728.9702>,<0,0.4786854,0.8779865>,<-102.7572,473.9388,-709.714>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1702,148.9579,-727.4569>,<0,0.2005802,0.9796773>,<-102.7602,475.3378,-709.9455>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1914,143.6144,-727.343>,<0,-0.1586376,0.9873369>,<-102.7574,476.4778,-710.2349>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-104.1928,140.3079,-728.2714>,<0,-0.3808012,0.9246569>,<-102.759,479.9376,-711.7562>,USE THEO=YES
ENDMEAS/
A2 =ALIGNMENT/START,RECALL:A1,LIST=YES
ALIGNMENT/TRANS,YAXIS,CIR1
ALIGNMENT/TRANS,ZAXIS,CIR1
ALIGNMENT/END
SAVE/ALIGNMENT,ClamTop2.aln,BOTH
RECALL/ALIGNMENT,EXTERNAL,CLAMTOP2
SAVE/ALIGNMENT,Loop Alignment.aln,BOTH
SAVE/ALIGNMENT,Loop1 Alignment.aln,BOTH
SAVE/ALIGNMENT,Loop2 Alignment.aln,BOTH
MODE/DCC
ASSIGN/LP1=5
ASSIGN/LP2=3
MOVE/POINT,NORMAL,<-265,0,374.756>
C1 =COMMENT/INPUT,NO,FULL SCREEN=YES,
Enter Operator Name
C2 =COMMENT/INPUT,NO,FULL SCREEN=YES,
Enter Batch Number
C3 =COMMENT/INPUT,NO,FULL SCREEN=YES,
Enter Cavity Number
C4 =COMMENT/INPUT,NO,FULL SCREEN=YES,
Enter part count
ASSIGN/V1=C1.INPUT
ASSIGN/V2=C2.INPUT
ASSIGN/V3=C3.INPUT
ASSIGN/V4=C4.INPUT
ASSIGN/LPP1=0
ASSIGN/LPP2=0
WHILE/LPP1<LP1
RECALL/ALIGNMENT,EXTERNAL,LOOP1 ALIGNMENT
COMMENT/REPT,
V1
COMMENT/REPT,
V2
COMMENT/REPT,
V3
COMMENT/REPT,
V4
CHECK/5,1
ONERROR/PROBE_MISS,GOTO L1
TOUCHSPEED/ 2
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,
Please Edit Comment Text!
MOVE/POINT,NORMAL,<-108.3765,-9.8301,47.302>
PNT43 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-109.1368,-9.6043>,<0,-0.9998477,0.0174524>
ACTL/<-109.1368,-74,10.6043>,<0,-0.9998477,0.0174524>
TARG/<-109.1368,-9.6043>,<0,-0.9998477,0.0174524>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO
A12 =ALIGNMENT/START,RECALL:A2,LIST=YES
ALIGNMENT/TRANS,YAXIS,PNT43
ALIGNMENT/TRANS_OFFSET,YAXIS,6.675
ALIGNMENT/END
MOVE/POINT,NORMAL,<-107.2781,-8,43.7868>
CIR3 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
THEO/<-96.5,-0.0001,0>,<-1,0,0>,30,0
ACTL/<-96.5,-0.2775,-0.1342>,<-1,0,0>,29.8378,0
TARG/<-96.5,-0.0001,0>,<-1,0,0>
START ANG=-30,END ANG=40
ANGLE VEC=<0,0,1>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO
MOVE/POINT,NORMAL,<-96.4998,8.2161,45.4023>
MOVE/POINT,NORMAL,<6.3529,-10.5765,43.7869>
PNT375 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<-0.0021,-12,5.6195>,<0.9998477,-0.0160941,0.0067502>
ACTL/<0.5302,-12.0119,5.6243>,<0.9998477,-0.0160941,0.0067502>
TARG/<-0.0021,-12,5.6195>,<0.9998477,-0.0160941,0.0067502>
SNAP=NO
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=NO
A13 =ALIGNMENT/START,RECALL:A12,LIST=YES
ALIGNMENT/TRANS,XAXIS,PNT375
ALIGNMENT/END
MOVE/POINT,NORMAL,<2.2456,-12.0401,44.8521>
PNT2 =FEAT/POINT,CARTESIAN,NO
THEO/<-96.4979,-0.0001,20>,<-1,0,0>
ACTL/<-97.0302,-0.2775,19.8658>,<-1,0,0>
CONSTR/POINT,OFFSET,CIR3,0,0,20
LIN1 =FEAT/LINE,CARTESIAN,UNBOUNDED,YES
THEO/<-96.5,-0.0001,0>,<0,0,-1>
ACTL/<-97.0302,-0.2775,19.8658>,<0,0,-1>
CONSTR/LINE,BF,2D,CIR3,PNT2,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
PNT3 =FEAT/POINT,CARTESIAN,NO
THEO/<-96.5,-0.0001,15>,<0,0,-1>
ACTL/<-97.0302,-0.2775,14.7847>,<0,0,-1>
CONSTR/POINT,PIERCE,CIR3,LIN1
A3 =ALIGNMENT/START,RECALL:A13,LIST=YES
ALIGNMENT/TRANS,ZAXIS,PNT3
ALIGNMENT/END
MOVE/POINT,NORMAL,<6.2052,-6.7966,22.2595>
WORKPLANE/YPLUS
PNT4 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<0.0023,11.2164,-6.1679>,<0.9998477,0.0137117,0.010797>
ACTL/<-0.1159,11.2107,-6.1689>,<0.9998477,0.0137117,0.010797>
TARG/<0.0023,11.2164,-6.1679>,<0.9998477,0.0137117,0.010797>
SNAP=NO
SHOW FEATURE PARAMETERS=YES
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
AUTO WRIST=YES
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
PNT5 =FEAT/CONTACT/VECTOR POINT/DEFAULT,CARTESIAN
THEO/<0.0007,4.4412,-1.3383>,<0.9998477,0.0053955,0.0165974>
ACTL/<-0.0992,4.437,-1.3381>,<0.9998477,0.0053955,0.0165974>
TARG/<0.0007,4.4412,-1.3383>,<0.9998477,0.0053955,0.0165974>
SNAP=NO
SHOW FEATURE PARAMETERS=YES
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
AUTO WRIST=YES
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
AVOIDANCE MOVE=NO,DISTANCE=10
SHOW HITS=NO
--------------------------------------------------------------


DIM DIM-7= 2D DISTANCE FROM LINE LIN52 TO LINE LIN49 PAR TO ZAXIS,NO_RADIUS UNITS=MM,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
M 0.9000 0.0500 0.0500 0.9235 0.0235 0.0000 ------#--
MOVE/POINT,NORMAL,<-1.2795,-0.5035,44.5362>
MOVE/POINT,NORMAL,<-250,0,303.4691>
LOADPROBE/1X40MM
TIP/T1A0B0, SHANKIJK=0.003, -0.0136, 0.9999, ANGLE=89.1929
MOVE/POINT,NORMAL,<-300.7658,0,363.0783>
PRINT/REPORT,EXEC MODE=END,$
TO_FILE=ON,AUTO=537,AUTO OPEN=ON,$
TO_PRINTER=OFF,COPIES=1,$
TO_DMIS_REPORT=OFF,FILE_OPTION=INDEX,FILENAME=,$
REPORT_THEORETICALS=NONE,REPORT_FEATURE_WITH_DIMEN SIONS=NO,$
TO_EXCEL=ON,APPEND,FILENAME=\\MAPAPP72\Mitutoyo\He xagon CMM\Programs\Loader Final Programs\DATA\Clam Top-2.CSV,AUTO OPEN=OFF,$
PREVIOUS_RUNS=DELETE_INSTANCES
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,
Please Edit Comment Text!
GOTO/L2
L1 =LABEL/
MOVE/INCREMENT,<0,0,20>
L2 =LABEL/
ASSIGN/V4=V4+1
TRANSALIGN =ALIGNMENT/START,RECALL:LOOP1 ALIGNMENT,LIST=YES
ALIGNMENT/TRANS_OFFSET,YAXIS,-65
ALIGNMENT/END
SAVE/ALIGNMENT,Loop1 Alignment.aln,BOTH
ASSIGN/LP1=LP1+1
END_WHILE/

Children

No Data