Max-Min points on scan

Hi,
how can i find the Max and Min points on scan along X or Y or Z ?
I need these values based on the actual reference sistem
Thanks

Parents

inspector212 over 17 years ago

FORMAT/TEXT,OPTIONS,ID,HEADINGS,SYMBOLS,SD;MEAS,NOM,TOL,DEV,OUTTOL,MAXMIN, 
DIM LOC100= PROFILE OF SURFACE OF SET SET1    FORMANDLOCATION  SD=0.000  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=40.00  OUTPUT=NONE
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL        MAX        MIN
M       0.000      0.000      0.750      0.750      0.000      0.000      0.000      0.000 --------|---------
            ASSIGN/PROF1MAX = LOC100.MAX
            ASSIGN/PROF1MIN = LOC100.MIN
PROF_SET1MAX=GENERIC/POINT,DEPENDENT,CARTESIAN,$
            NOM/XYZ,<PROF1MAX,0,0>,$
            MEAS/XYZ,<PROF1MAX,817.363,-647.605>,$
            NOM/IJK,<0,0,1>,$
            MEAS/IJK,<0,0,1>
PROF_SET1MIN=GENERIC/POINT,DEPENDENT,CARTESIAN,$
            NOM/XYZ,<PROF1MIN,-545.904,0>,$
            MEAS/XYZ,<PROF1MIN,271.465,-646.71>,$
            NOM/IJK,<0,0,1>,$
            MEAS/IJK,<0,0,1>
            ANALYSISVIEW/LOC100,,
            COMMENT/REPT,LOC101, MAX Profile to inside radius around Datum C
                        ,at 69.6mm from Datum C pocket
            FORMAT/TEXT,OPTIONS,ID,HEADINGS,SYMBOLS,SD;MEAS,NOM,TOL,DEV,OUTTOL, , 
DIM LOC101= LOCATION OF POINT PROF_SET1MAX  SD=0.000  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=40.00  OUTPUT=BOTH
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X       0.000      0.000      0.750      0.750      0.000      0.000 --------#---------
END OF DIMENSION LOC101
            COMMENT/REPT,LOC102, MIN Profile to inside radius around Datum C
                        ,at 69.6mm from Datum C pocket
DIM LOC102= LOCATION OF POINT PROF_SET1MIN  SD=0.000  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=40.00  OUTPUT=BOTH
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X       0.000      0.000      0.750      0.750      0.000      0.000 --------#---------
END OF DIMENSION LOC102

This will give you the MAX and MIN deviation of a scan when using the profile of a surface button. If you only want the MAX part you can delete the MIN.

Reply

inspector212 over 17 years ago

FORMAT/TEXT,OPTIONS,ID,HEADINGS,SYMBOLS,SD;MEAS,NOM,TOL,DEV,OUTTOL,MAXMIN, 
DIM LOC100= PROFILE OF SURFACE OF SET SET1    FORMANDLOCATION  SD=0.000  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=40.00  OUTPUT=NONE
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL        MAX        MIN
M       0.000      0.000      0.750      0.750      0.000      0.000      0.000      0.000 --------|---------
            ASSIGN/PROF1MAX = LOC100.MAX
            ASSIGN/PROF1MIN = LOC100.MIN
PROF_SET1MAX=GENERIC/POINT,DEPENDENT,CARTESIAN,$
            NOM/XYZ,<PROF1MAX,0,0>,$
            MEAS/XYZ,<PROF1MAX,817.363,-647.605>,$
            NOM/IJK,<0,0,1>,$
            MEAS/IJK,<0,0,1>
PROF_SET1MIN=GENERIC/POINT,DEPENDENT,CARTESIAN,$
            NOM/XYZ,<PROF1MIN,-545.904,0>,$
            MEAS/XYZ,<PROF1MIN,271.465,-646.71>,$
            NOM/IJK,<0,0,1>,$
            MEAS/IJK,<0,0,1>
            ANALYSISVIEW/LOC100,,
            COMMENT/REPT,LOC101, MAX Profile to inside radius around Datum C
                        ,at 69.6mm from Datum C pocket
            FORMAT/TEXT,OPTIONS,ID,HEADINGS,SYMBOLS,SD;MEAS,NOM,TOL,DEV,OUTTOL, , 
DIM LOC101= LOCATION OF POINT PROF_SET1MAX  SD=0.000  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=40.00  OUTPUT=BOTH
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X       0.000      0.000      0.750      0.750      0.000      0.000 --------#---------
END OF DIMENSION LOC101
            COMMENT/REPT,LOC102, MIN Profile to inside radius around Datum C
                        ,at 69.6mm from Datum C pocket
DIM LOC102= LOCATION OF POINT PROF_SET1MIN  SD=0.000  UNITS=MM ,$
GRAPH=OFF  TEXT=OFF  MULT=40.00  OUTPUT=BOTH
AX       MEAS    NOMINAL       +TOL       -TOL        DEV     OUTTOL
X       0.000      0.000      0.750      0.750      0.000      0.000 --------#---------
END OF DIMENSION LOC102

This will give you the MAX and MIN deviation of a scan when using the profile of a surface button. If you only want the MAX part you can delete the MIN.

Children

No Data