Your Products have been synced, click here to refresh
I am struggling with what seems to be a simple part it’s three holes all in line the datum’s are based on one circle that’s measured CWW but when I try to do an auto feature the probe crashes into the part and then it can’t locate the other two holes. any suggestions on how to set up the alignment again it’s based off of the middle outside radius and the small bore to the right of the middle bore. 
if you click on insert, then code "</> Code" put it in there.
I’m not in the office I will be soon when I am I will post that
okay i see you're in summary mode, switch to command mode whenever you post it :)
PART NAME : OUTER MEMBER_
REV NUMBER : 2
SER NUMBER :
STATS COUNT : 1
STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
ALIGNMENT/END
MODE/MANUAL
PREHIT/0.001
RETRACT/0.001
FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;MEAS,NOM,TOL,DEV,OUTTOL, ,
TEMPCOMP/METHOD = AUTOMATIC,MATERIAL = Zerodur; Nexcera,CTE=0
,SET WARNING LIMIT = FALSE,MINIMUM = 10,MAXIMUM = 40
,PART SENSOR NUM=DEFAULT,X SCALE= 25.1872,Y SCALE= 24.6185,Z SCALE= 25.6919,PART TEMP=24.7725
LOADPROBE/SPHERE PROBE
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
MANRETRACT/0.01
MAN_ALIGN =GROUP/SHOWALLPARAMS=YES
PLN1 =FEAT/PLANE,CARTESIAN,TRIANGLE
THEO/<0.0728,-0.0684,0.032>,<0,0,1>
ACTL/<5.6545,3.0549,-15.1778>,<0.000014,-0.0006627,0.9999998>
MEAS/PLANE,6
HIT/BASIC,NORMAL,<-0.5035,0.1239,0.032>,<0,0,1>,<5.0706,3.2287,-15.1775>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.5042,-0.1221,0.032>,<0,0,1>,<5.0927,2.9953,-15.1782>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0087,-0.4086,0.032>,<0,0,1>,<5.6013,2.6938,-15.1775>,USE THEO=YES
HIT/BASIC,NORMAL,<0.4859,-0.1784,0.032>,<0,0,1>,<6.0542,2.9847,-15.1785>,USE THEO=YES
HIT/BASIC,NORMAL,<0.47,0.0014,0.032>,<0,0,1>,<6.0542,3.2134,-15.1775>,USE THEO=YES
HIT/BASIC,NORMAL,<0.497,0.1735,0.032>,<0,0,1>,<6.0542,3.2134,-15.1775>,USE THEO=YES
ENDMEAS/
A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/END
CIR1 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0.625,0,0>,<0,0,1>,0.134
ACTL/<6.2132,3.101,0>,<0,0,1>,0.1344
TARG/<0.625,0,0>,<0,0,1>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=YES
VOID DETECTION=NO
REMEASURE=NO
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
AUTO WRIST=NO
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
NUMHITS=4,DEPTH=0.009,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=YES
HIT/BASIC,<0.692,0,-0.009>,<-1,0,0>,<6.2797,3.1118,-0.0143>
HIT/BASIC,<0.625,0.067,-0.009>,<0,-1,0>,<6.211,3.1679,-0.0143>
HIT/BASIC,<0.558,0,-0.009>,<1,0,0>,<6.1481,3.1184,-0.0143>
HIT/BASIC,<0.625,-0.067,-0.009>,<0,1,0>,<6.1943,3.0366,-0.0143>
ENDMEAS/
A2 =ALIGNMENT/START,RECALL:A1,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/TRANS,XAXIS,CIR1
ALIGNMENT/TRANS,YAXIS,CIR1
ALIGNMENT/END
CIR2 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
THEO/<-0.625,0,0.0796>,<0,0,1>,0.725,0
ACTL/<-0.6253,-0.0041,0.0796>,<0,0,1>,0.7248,0
TARG/<-0.625,0,0.0796>,<0,0,1>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=YES
VOID DETECTION=NO
REMEASURE=NO
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
AUTO WRIST=NO
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
NUMHITS=4,DEPTH=-0.05,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=YES
HIT/BASIC,<-0.2625,0,0.0296>,<1,0,0>,<-0.2653,-0.0337,0.0549>
HIT/BASIC,<-0.625,0.3625,0.0296>,<0,1,0>,<-0.6706,0.3566,0.0546>
HIT/BASIC,<-0.9875,0,0.0296>,<-1,0,0>,<-0.9851,-0.0351,0.0401>
HIT/BASIC,<-0.625,-0.3625,0.0296>,<0,-1,0>,<-0.582,-0.3653,0.037>
ENDMEAS/
A3 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/TRANS,XAXIS,CIR1
ALIGNMENT/TRANS,YAXIS,CIR1
ALIGNMENT/ROTATE_CIRCLE,XMINUS,TO,CIR1,AND,CIR2,ABOUT,ZPLUS
ALIGNMENT/END
ENDGROUP/ID=MAN_ALIGN
DCC_ALIGN =GROUP/SHOWALLPARAMS=YES
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,OVC=NO,
Changing to DCC mode! Do not continue unless avoidance moves have been added.
MODE/DCC
PLN1_DCC =FEAT/PLANE,CARTESIAN,TRIANGLE
THEO/<-0.6399,0.0101,0>,<0,0,1>
ACTL/<-0.7423,-0.0226,-0.0003>,<0.0003427,-0.0015121,0.9999988>
MEAS/PLANE,5
HIT/BASIC,NORMAL,<-1.1752,0.1745,0>,<0,0,1>,<-1.1752,0.1745,0>,USE THEO=YES
HIT/BASIC,NORMAL,<-1.0883,0.0209,0>,<0,0,1>,<-1.0883,0.0209,0>,USE THEO=YES
HIT/BASIC,NORMAL,<-1.1485,-0.1369,0>,<0,0,1>,<-1.1485,-0.1369,0>,USE THEO=YES
MOVE/POINT,NORMAL,<-0.6336,-0.4063,0.9122>
HIT/BASIC,NORMAL,<-0.1205,-0.1814,0>,<0,0,1>,<-0.1205,-0.1814,0>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.1788,0.0098,0>,<0,0,1>,<-0.1788,0.0098,0>,USE THEO=YES
ENDMEAS/
A3_DCC1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1_DCC
ALIGNMENT/TRANS,ZAXIS,PLN1_DCC
ALIGNMENT/TRANS,XAXIS,CIR1
ALIGNMENT/TRANS,YAXIS,CIR1
ALIGNMENT/ROTATE_CIRCLE,XMINUS,TO,CIR1,AND,CIR2,ABOUT,ZPLUS
ALIGNMENT/END
CIR1_DCC =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,0,0>,<0,0,1>,0.134
ACTL/<0,0,0>,<0,0,1>,0.1355
TARG/<0,0,0>,<0,0,1>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=YES
VOID DETECTION=NO
REMEASURE=NO
SURFACE=THICKNESS_NONE,0
MEASURE MODE=NOMINALS
RMEAS=NONE,NONE,NONE
AUTO WRIST=NO
CIRCULAR MOVES=STRAIGHT
GRAPHICAL ANALYSIS=NO
FEATURE LOCATOR=NO,NO,""
SHOW CONTACT PARAMETERS=YES
NUMHITS=4,DEPTH=0.009,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=YES
HIT/BASIC,<0.067,0,-0.009>,<-1,0,0>,<0.067,0,-0.009>
HIT/BASIC,<0,0.067,-0.009>,<0,-1,0>,<0,0.067,-0.009>
HIT/BASIC,<-0.067,0,-0.009>,<1,0,0>,<-0.067,0,-0.009>
HIT/BASIC,<0,-0.067,-0.009>,<0,1,0>,<0,-0.067,-0.009>
ENDMEAS/
A3_DCC2 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1_DCC
ALIGNMENT/TRANS,ZAXIS,PLN1_DCC
ALIGNMENT/TRANS,XAXIS,CIR1_DCC
ALIGNMENT/TRANS,YAXIS,CIR1_DCC
ALIGNMENT/ROTATE_CIRCLE,XMINUS,TO,CIR1_DCC,AND,CIR2,ABOUT,ZPLUS
ALIGNMENT/END
CIR5 =FEAT/CIRCLE,CARTESIAN,OUT,LEAST_SQR
THEO/<-0.6257,-0.0007,0.0531>,<0,0,1>,0.7247,0
ACTL/<-0.6257,-0.0007,0.0531>,<0,0,1>,0.7247,0
MEAS/CIRCLE,10,ZPLUS
HIT/BASIC,NORMAL,<-0.2634,-0.0007,0.0531>,<1,0,0>,<-0.2634,-0.0007,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.3326,0.2123,0.0531>,<0.809017,0.5877853,0>,<-0.3326,0.2123,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.5137,0.3439,0.0531>,<0.309017,0.9510565,0>,<-0.5137,0.3439,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.7377,0.3439,0.0531>,<-0.309017,0.9510565,0>,<-0.7377,0.3439,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.9189,0.2123,0.0531>,<-0.809017,0.5877853,0>,<-0.9189,0.2123,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.9881,-0.0007,0.0531>,<-1,0,0>,<-0.9881,-0.0007,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.9189,-0.2137,0.0531>,<-0.809017,-0.5877853,0>,<-0.9189,-0.2137,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.7377,-0.3453,0.0531>,<-0.309017,-0.9510565,0>,<-0.7377,-0.3453,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.5137,-0.3453,0.0531>,<0.309017,-0.9510565,0>,<-0.5137,-0.3453,0.0531>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<-0.3326,-0.2137,0.0531>,<0.809017,-0.5877853,0>,<-0.3326,-0.2137,0.0531>,USE THEO=YES
ENDMEAS/
A3_DCC3 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1_DCC
ALIGNMENT/TRANS,ZAXIS,PLN1_DCC
ALIGNMENT/TRANS,XAXIS,CIR1_DCC
ALIGNMENT/TRANS,YAXIS,CIR1_DCC
ALIGNMENT/ROTATE_CIRCLE,XMINUS,TO,CIR1_DCC,AND,CIR5,ABOUT,ZPLUS
ALIGNMENT/END
LIN1 =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
THEO/<0,0,0>,<-0.9964162,0,0.0845853>
ACTL/<0,0,0>,<-0.9964162,0,0.0845853>
CONSTR/LINE,BF,3D,CIR1_DCC,CIR5,,
OUTLIER_REMOVAL/OFF,3
FILTER/OFF,WAVELENGTH=0
A4 =ALIGNMENT/START,RECALL:A3_DCC3,LIST=YES
ALIGNMENT/LEVEL,XMINUS,LIN1
ALIGNMENT/TRANS,YAXIS,LIN1
ALIGNMENT/TRANS,ZAXIS,LIN1
ALIGNMENT/END
ENDGROUP/ID=DCC_ALIGN
CIR4 =FEAT/CIRCLE,CARTESIAN,IN,LEAST_SQR
THEO/<-1.2473,-0.0006,-0.1217>,<-0.0845853,0,0.9964162>,0.1341
ACTL/<-1.2448,0.0027,-0.1213>,<-0.0851961,-0.0011469,0.9963635>,0.1341
MEAS/CIRCLE,4,ZPLUS
HIT/BASIC,NORMAL,<-1.2375,-0.0667,-0.1208>,<-0.1477818,0.9889404,-0.0125451>,<-1.2337,-0.0736,-0.1203>,USE THEO=YES
HIT/BASIC,NORMAL,<-1.3143,-0.0058,-0.1274>,<0.9934624,0.0769431,0.0843345>,<-1.3219,-0.0029,-0.1279>,USE THEO=YES
HIT/BASIC,NORMAL,<-1.3002,0.0399,-0.1264>,<0.7913694,-0.607636,0.067179>,<-1.3056,0.0497,-0.1266>,USE THEO=YES
HIT/BASIC,NORMAL,<-1.1806,-0.0064,-0.1161>,<-0.9927878,0.0852626,-0.0842773>,<-1.1679,-0.0041,-0.1148>,USE THEO=YES
ENDMEAS/Either define a Clearplane, so "CLEARP/ZPLUS,0.5,ZPLUS,0,ON" and put in a move clearplane before each feature, or you can use the avoidance moves. I generally just use clearplanes for all my programs though.
Your prehit and retract being .001 are scary, is there a reason they are so low? You are also not using clear planes or declaring any
and exactly this, open up those prehits and retracts
and exactly this, open up those prehits and retracts
| © 2024 Hexagon AB and/or its subsidiaries. | Privacy Policy | Cloud Services Agreement |