losing information

I have pc-dimis 2010. I write a program and run it through as i write it.My measurement checks will be correct but then as i go along writing the program and running through the new measurements I lose data from other measurements.My nominals will change and it will run through the program and then tell me that some of the features did not measure .What am I doing wrong? Any ideas?

Parents

John Kingston over 14 years ago

My understanding is PC-DMIS Portable is geared towards Romer and other arm type machines. I don't really consider the Discovery to be "portable" in that sense, it is more of a bridge type CMM.
Not many look in this forum unless they use an arm machine, or happen to click on "New Posts". That's how I saw your post.

On to your code. First off, clean up your theos. ( see red below).
Is there a Manual alignment, Readpoint, or some way of locating the part the same way each time?
Next time you run a part, how will you locate it?

If you are using alt-E, that only executes the FEATURE it is in. Since your dimensioning takes place after all your measurement code, it does not "run" it.
Alt-U runs all the code AFTER the cursor.

PART NAME : 9372
REV NUMBER : 
SER NUMBER : 
STATS COUNT : 1

STARTUP =ALIGNMENT/START,RECALL:,LIST=YES
ALIGNMENT/END
MODE/DCC
FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, , 

LOADPROBE/B89
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0

PLN1 =FEAT/PLANE,CARTESIAN,TRIANGLE
[COLOR="red"]THEO/<0,0,0>,<-0.0025399,0.0009064,0.9999964>[/COLOR]
ACTL/<10.2222,11.1005,-15.8074>,<-0.0020791,0.0000373,0.9999978>
MEAS/PLANE,9
HIT/BASIC,NORMAL,<10.0177,11.7549,-15.7759>,<-0.0025399,0.0009064,0.9999964>,<10.0179,11.7537,-15.8078>,USE THEO=YES
HIT/BASIC,NORMAL,<10.4008,11.7549,-15.7749>,<-0.0025399,0.0009064,0.9999964>,<10.3997,11.7537,-15.807>,USE THEO=YES
HIT/BASIC,NORMAL,<10.4009,11.5403,-15.7747>,<-0.0025399,0.0009064,0.9999964>,<10.3998,11.5405,-15.807>,USE THEO=YES
HIT/BASIC,NORMAL,<10.778,10.9494,-15.7735>,<-0.0025399,0.0009064,0.9999964>,<10.777,10.9495,-15.8064>,USE THEO=YES
HIT/BASIC,NORMAL,<10.5729,10.552,-15.7732>,<-0.0025399,0.0009064,0.9999964>,<10.5731,10.552,-15.8065>,USE THEO=YES
HIT/BASIC,NORMAL,<10.2272,10.4704,-15.7742>,<-0.0025399,0.0009064,0.9999964>,<10.2275,10.4703,-15.8073>,USE THEO=YES
HIT/BASIC,NORMAL,<9.8839,10.4705,-15.775>,<-0.0025399,0.0009064,0.9999964>,<9.8843,10.4701,-15.808>,USE THEO=YES
HIT/BASIC,NORMAL,<9.7014,10.7986,-15.7761>,<-0.0025399,0.0009064,0.9999964>,<9.7016,10.7974,-15.8086>,USE THEO=YES
HIT/BASIC,NORMAL,<10.0197,11.6185,-15.7758>,<-0.0025399,0.0009064,0.9999964>,<10.0187,11.6173,-15.8078>,USE THEO=YES
ENDMEAS/

SLOT 1 =FEAT/LINE,CARTESIAN,UNBOUNDED
THEO/<9.9957,11.9002,-15.7954>,<0.9998931,0.01462,0>
ACTL/<9.9952,11.884,-15.7945>,<0.9998858,0.0151093,0>
MEAS/LINE,2,WORKPLANE
HIT/BASIC,NORMAL,<9.9957,11.9002,-15.7955>,<-0.0146498,0.9998927,0>,<9.9952,11.884,-15.7944>,USE THEO=YES
HIT/BASIC,NORMAL,<10.3918,11.906,-15.7953>,<-0.0146498,0.9998927,0>,<10.3906,11.89,-15.7946>,USE THEO=YES
ENDMEAS/

CYL1 =FEAT/CYLINDER,CARTESIAN,IN,LEAST_SQR
THEO/<10.2164,11.0039,-16.0842>,<-0.0011196,-0.0006563,-0.9999992>,0.9383,0.2997
ACTL/<10.2183,11.0027,-16.083>,<-0.000341,-0.000278,-0.9999999>,0.9379,0.2987
MEAS/CYLINDER,11
HIT/BASIC,NORMAL,<10.6787,11.0872,-15.9351>,<-0.9841587,-0.1772853,0.0012182>,<10.6808,11.0837,-15.9339>,USE THEO=YES
HIT/BASIC,NORMAL,<10.1723,10.5372,-15.9348>,<0.0944311,0.9955311,-0.0007591>,<10.1735,10.5365,-15.9341>,USE THEO=YES
HIT/BASIC,NORMAL,<10.2882,11.4673,-15.9347>,<-0.1528291,-0.9882523,0.0008197>,<10.2873,11.4662,-15.9341>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<10.4244,11.4242,-16.114>,<-0.4435972,-0.8962256,0.0010849>,<10.4236,11.424,-16.1117>,USE THEO=YES
HIT/BASIC,NORMAL,<10.3815,10.5649,-16.1132>,<-0.352188,0.9359293,-0.00022>,<10.3798,10.5626,-16.1122>,USE THEO=YES
HIT/BASIC,NORMAL,<9.7843,10.8194,-16.1133>,<0.9197146,0.3925855,-0.0012874>,<9.7843,10.8224,-16.1122>,USE THEO=YES
HIT/BASIC,NORMAL,<9.9457,11.3872,-16.1134>,<0.576751,-0.81692,-0.0001095>,<9.947,11.3854,-16.1122>,USE THEO=YES
HIT/BASIC,NORMAL,<9.9844,11.4114,-16.2333>,<0.4943753,-0.8692486,0.000017>,<9.9865,11.4104,-16.2313>,USE THEO=YES
HIT/BASIC,NORMAL,<10.512,11.3683,-16.2334>,<-0.6300242,-0.7765745,0.0012151>,<10.5118,11.3685,-16.232>,USE THEO=YES
HIT/BASIC,NORMAL,<10.4686,10.608,-16.2335>,<-0.5376309,0.8431803,0.0000485>,<10.4679,10.6053,-16.2321>,USE THEO=YES
HIT/BASIC,NORMAL,<9.9077,10.6506,-16.2335>,<0.6579001,0.7531042,-0.0012309>,<9.9087,10.6513,-16.2322>,USE THEO=YES
ENDMEAS/

A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/ROTATE,XPLUS,TO,SLOT 1,ABOUT,ZPLUS
ALIGNMENT/TRANS,XAXIS,CYL1
ALIGNMENT/TRANS,YAXIS,CYL1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/END
FACE =FEAT/PLANE,CARTESIAN,TRIANGLE
THEO/<-0.0397,0.0592,-0.0001>,<-0.0004458,-0.0000321,0.9999999>
ACTL/<-0.0398,0.0588,-0.0001>,<-0.0004416,-0.0000178,0.9999999>
MEAS/PLANE,8
MOVE/POINT,NORMAL,PART,<-0.1894,1.0490,0.0793>
HIT/BASIC,NORMAL,<-0.2302,0.7954,0>,<-0.0004458,-0.0000321,0.9999999>,<-0.2299,0.7966,0>,USE THEO=YES
HIT/BASIC,NORMAL,<0.1277,0.7902,0.0001>,<-0.0004458,-0.0000321,0.9999999>,<0.126,0.7901,0.0001>,USE THEO=YES
HIT/BASIC,NORMAL,<0.5272,-0.1488,-0.0003>,<-0.0004458,-0.0000321,0.9999999>,<0.5259,-0.1478,-0.0003>,USE THEO=YES
HIT/BASIC,NORMAL,<0.3385,-0.469,0.0002>,<-0.0004458,-0.0000321,0.9999999>,<0.3393,-0.4681,0.0002>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.038,-0.5677,0>,<-0.0004458,-0.0000321,0.9999999>,<-0.0368,-0.5674,0.0001>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.3084,-0.5462,0.0001>,<-0.0004458,-0.0000321,0.9999999>,<-0.3074,-0.5475,0.0001>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.5382,0.0069,-0.001>,<-0.0004458,-0.0000321,0.9999999>,<-0.5377,0.0043,-0.001>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.1959,0.6126,0>,<-0.0004458,-0.0000321,0.9999999>,<-0.1974,0.6102,0>,USE THEO=YES
ENDMEAS/

TOP OF RAIL=FEAT/LINE,CARTESIAN,UNBOUNDED
THEO/<-0.1916,0.8998,-0.1414>,<0.9999997,0.000779,0>
ACTL/<-0.1926,0.9001,-0.1393>,<0.9999983,0.001851,0>
MEAS/LINE,2,WORKPLANE
HIT/BASIC,NORMAL,<-0.1916,0.8998,-0.1408>,<-0.0007723,0.9999997,0>,<-0.1926,0.9001,-0.1385>,USE THEO=YES
HIT/BASIC,NORMAL,<0.2294,0.9001,-0.1419>,<-0.0007723,0.9999997,0>,<0.2272,0.9008,-0.1401>,USE THEO=YES
ENDMEAS/

BORE =FEAT/CIRCLE,CARTESIAN,IN,LEAST_SQR
THEO/<0,-0.0001,-0.0857>,<0,0,1>,0.9387
ACTL/<0,-0.0001,-0.0845>,<0,0,1>,0.9385
MEAS/CIRCLE,4,WORKPLANE
HIT/BASIC,NORMAL,<0.0055,0.4688,-0.0853>,<-0.0117221,-0.9999313,0>,<0.0057,0.4686,-0.0843>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0083,-0.4689,-0.0861>,<0.0179005,0.9998398,0>,<-0.0086,-0.4684,-0.0846>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.4658,-0.0608,-0.0847>,<0.9916206,0.1291842,0>,<-0.4659,-0.0621,-0.0837>,USE THEO=YES
HIT/BASIC,NORMAL,<0.4637,-0.0757,-0.0869>,<-0.9869764,0.1608653,0>,<0.4643,-0.0726,-0.0855>,USE THEO=YES
ENDMEAS/

GAS TUBE =FEAT/CYLINDER,CARTESIAN,IN,LEAST_SQR
THEO/<-0.0018,0.6252,-0.0703>,<-0.0000204,0.0025611,-0.9999967>,0.1831,0.0864
ACTL/<-0.0027,0.6251,-0.0692>,<-0.0000406,-0.0026846,-0.9999964>,0.1829,0.0867
MEAS/CYLINDER,12
HIT/BASIC,NORMAL,<0.0019,0.7165,-0.0272>,<-0.0397717,-0.9992055,-0.0025583>,<-0.0022,0.7164,-0.0261>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0076,0.5338,-0.0274>,<0.0644409,0.9979183,0.0025545>,<-0.0049,0.5341,-0.0262>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0907,0.6034,-0.0272>,<0.971627,0.2365179,0.000586>,<-0.0929,0.6089,-0.0262>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0866,0.6007,-0.0274>,<-0.9641769,0.2652592,0.000699>,<0.0869,0.6058,-0.0264>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0193,0.7142,-0.0735>,<-0.2301759,-0.9731459,-0.0024877>,<0.0134,0.715,-0.072>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0167,0.5356,-0.0738>,<-0.2014683,0.9794918,0.0025127>,<0.011,0.5347,-0.0723>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0911,0.6051,-0.0735>,<0.9757509,0.2188832,0.0005407>,<-0.0932,0.6108,-0.0723>,USE THEO=YES
HIT/BASIC,NORMAL,<0.087,0.6025,-0.0738>,<-0.9687836,0.247907,0.0006546>,<0.0872,0.6078,-0.0725>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.091,0.6051,-0.1133>,<0.9753543,0.2206438,0.0005452>,<-0.0928,0.6092,-0.1118>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0235,0.7142,-0.1132>,<0.2376487,-0.971348,-0.0024926>,<-0.0175,0.7151,-0.1125>,USE THEO=YES
HIT/BASIC,NORMAL,<0.088,0.6433,-0.1135>,<-0.9804665,-0.1966855,-0.0004838>,<0.0882,0.6356,-0.1126>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0177,0.5358,-0.1135>,<-0.211973,0.9772723,0.0025072>,<0.0107,0.5346,-0.1123>,USE THEO=YES
ENDMEAS/



ENDMEAS/

DIM RAIL= 2D DISTANCE FROM CIRCLE BORE TO LINE TOP OF RAIL PAR TO XAXIS,NO_RADIUS UNITS=IN,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
M 0.9000 0.0100 -0.0100 0.0173 -0.8827 -0.8727 <--------
DIM LOC2= LOCATION OF CYLINDER GAS TUBE UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
DIM DIST2= 2D DISTANCE FROM CIRCLE BORE TO CYLINDER GAS TUBE PAR TO YAXIS,NO_RADIUS UNITS=IN,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
M 0.6250 0.0030 -0.0030 0.0000 -0.6250 -0.6220 <--------
DIM DIST3= 2D DISTANCE FROM CIRCLE BORE TO LINE RIGHT SIDE (CENTER TO CENTER),NO_RADIUS UNITS=IN,$
0.0050(orig .614)-0.0050 0.6140 0.0000 0.0000 ----#----

Reply

John Kingston over 14 years ago

PART NAME : 9372
REV NUMBER : 
SER NUMBER : 
STATS COUNT : 1

STARTUP =ALIGNMENT/START,RECALL:,LIST=YES
ALIGNMENT/END
MODE/DCC
FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, , 

LOADPROBE/B89
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0

PLN1 =FEAT/PLANE,CARTESIAN,TRIANGLE
[COLOR="red"]THEO/<0,0,0>,<-0.0025399,0.0009064,0.9999964>[/COLOR]
ACTL/<10.2222,11.1005,-15.8074>,<-0.0020791,0.0000373,0.9999978>
MEAS/PLANE,9
HIT/BASIC,NORMAL,<10.0177,11.7549,-15.7759>,<-0.0025399,0.0009064,0.9999964>,<10.0179,11.7537,-15.8078>,USE THEO=YES
HIT/BASIC,NORMAL,<10.4008,11.7549,-15.7749>,<-0.0025399,0.0009064,0.9999964>,<10.3997,11.7537,-15.807>,USE THEO=YES
HIT/BASIC,NORMAL,<10.4009,11.5403,-15.7747>,<-0.0025399,0.0009064,0.9999964>,<10.3998,11.5405,-15.807>,USE THEO=YES
HIT/BASIC,NORMAL,<10.778,10.9494,-15.7735>,<-0.0025399,0.0009064,0.9999964>,<10.777,10.9495,-15.8064>,USE THEO=YES
HIT/BASIC,NORMAL,<10.5729,10.552,-15.7732>,<-0.0025399,0.0009064,0.9999964>,<10.5731,10.552,-15.8065>,USE THEO=YES
HIT/BASIC,NORMAL,<10.2272,10.4704,-15.7742>,<-0.0025399,0.0009064,0.9999964>,<10.2275,10.4703,-15.8073>,USE THEO=YES
HIT/BASIC,NORMAL,<9.8839,10.4705,-15.775>,<-0.0025399,0.0009064,0.9999964>,<9.8843,10.4701,-15.808>,USE THEO=YES
HIT/BASIC,NORMAL,<9.7014,10.7986,-15.7761>,<-0.0025399,0.0009064,0.9999964>,<9.7016,10.7974,-15.8086>,USE THEO=YES
HIT/BASIC,NORMAL,<10.0197,11.6185,-15.7758>,<-0.0025399,0.0009064,0.9999964>,<10.0187,11.6173,-15.8078>,USE THEO=YES
ENDMEAS/

SLOT 1 =FEAT/LINE,CARTESIAN,UNBOUNDED
THEO/<9.9957,11.9002,-15.7954>,<0.9998931,0.01462,0>
ACTL/<9.9952,11.884,-15.7945>,<0.9998858,0.0151093,0>
MEAS/LINE,2,WORKPLANE
HIT/BASIC,NORMAL,<9.9957,11.9002,-15.7955>,<-0.0146498,0.9998927,0>,<9.9952,11.884,-15.7944>,USE THEO=YES
HIT/BASIC,NORMAL,<10.3918,11.906,-15.7953>,<-0.0146498,0.9998927,0>,<10.3906,11.89,-15.7946>,USE THEO=YES
ENDMEAS/

CYL1 =FEAT/CYLINDER,CARTESIAN,IN,LEAST_SQR
THEO/<10.2164,11.0039,-16.0842>,<-0.0011196,-0.0006563,-0.9999992>,0.9383,0.2997
ACTL/<10.2183,11.0027,-16.083>,<-0.000341,-0.000278,-0.9999999>,0.9379,0.2987
MEAS/CYLINDER,11
HIT/BASIC,NORMAL,<10.6787,11.0872,-15.9351>,<-0.9841587,-0.1772853,0.0012182>,<10.6808,11.0837,-15.9339>,USE THEO=YES
HIT/BASIC,NORMAL,<10.1723,10.5372,-15.9348>,<0.0944311,0.9955311,-0.0007591>,<10.1735,10.5365,-15.9341>,USE THEO=YES
HIT/BASIC,NORMAL,<10.2882,11.4673,-15.9347>,<-0.1528291,-0.9882523,0.0008197>,<10.2873,11.4662,-15.9341>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<10.4244,11.4242,-16.114>,<-0.4435972,-0.8962256,0.0010849>,<10.4236,11.424,-16.1117>,USE THEO=YES
HIT/BASIC,NORMAL,<10.3815,10.5649,-16.1132>,<-0.352188,0.9359293,-0.00022>,<10.3798,10.5626,-16.1122>,USE THEO=YES
HIT/BASIC,NORMAL,<9.7843,10.8194,-16.1133>,<0.9197146,0.3925855,-0.0012874>,<9.7843,10.8224,-16.1122>,USE THEO=YES
HIT/BASIC,NORMAL,<9.9457,11.3872,-16.1134>,<0.576751,-0.81692,-0.0001095>,<9.947,11.3854,-16.1122>,USE THEO=YES
HIT/BASIC,NORMAL,<9.9844,11.4114,-16.2333>,<0.4943753,-0.8692486,0.000017>,<9.9865,11.4104,-16.2313>,USE THEO=YES
HIT/BASIC,NORMAL,<10.512,11.3683,-16.2334>,<-0.6300242,-0.7765745,0.0012151>,<10.5118,11.3685,-16.232>,USE THEO=YES
HIT/BASIC,NORMAL,<10.4686,10.608,-16.2335>,<-0.5376309,0.8431803,0.0000485>,<10.4679,10.6053,-16.2321>,USE THEO=YES
HIT/BASIC,NORMAL,<9.9077,10.6506,-16.2335>,<0.6579001,0.7531042,-0.0012309>,<9.9087,10.6513,-16.2322>,USE THEO=YES
ENDMEAS/

A1 =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
ALIGNMENT/LEVEL,ZPLUS,PLN1
ALIGNMENT/ROTATE,XPLUS,TO,SLOT 1,ABOUT,ZPLUS
ALIGNMENT/TRANS,XAXIS,CYL1
ALIGNMENT/TRANS,YAXIS,CYL1
ALIGNMENT/TRANS,ZAXIS,PLN1
ALIGNMENT/END
FACE =FEAT/PLANE,CARTESIAN,TRIANGLE
THEO/<-0.0397,0.0592,-0.0001>,<-0.0004458,-0.0000321,0.9999999>
ACTL/<-0.0398,0.0588,-0.0001>,<-0.0004416,-0.0000178,0.9999999>
MEAS/PLANE,8
MOVE/POINT,NORMAL,PART,<-0.1894,1.0490,0.0793>
HIT/BASIC,NORMAL,<-0.2302,0.7954,0>,<-0.0004458,-0.0000321,0.9999999>,<-0.2299,0.7966,0>,USE THEO=YES
HIT/BASIC,NORMAL,<0.1277,0.7902,0.0001>,<-0.0004458,-0.0000321,0.9999999>,<0.126,0.7901,0.0001>,USE THEO=YES
HIT/BASIC,NORMAL,<0.5272,-0.1488,-0.0003>,<-0.0004458,-0.0000321,0.9999999>,<0.5259,-0.1478,-0.0003>,USE THEO=YES
HIT/BASIC,NORMAL,<0.3385,-0.469,0.0002>,<-0.0004458,-0.0000321,0.9999999>,<0.3393,-0.4681,0.0002>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.038,-0.5677,0>,<-0.0004458,-0.0000321,0.9999999>,<-0.0368,-0.5674,0.0001>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.3084,-0.5462,0.0001>,<-0.0004458,-0.0000321,0.9999999>,<-0.3074,-0.5475,0.0001>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.5382,0.0069,-0.001>,<-0.0004458,-0.0000321,0.9999999>,<-0.5377,0.0043,-0.001>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.1959,0.6126,0>,<-0.0004458,-0.0000321,0.9999999>,<-0.1974,0.6102,0>,USE THEO=YES
ENDMEAS/

TOP OF RAIL=FEAT/LINE,CARTESIAN,UNBOUNDED
THEO/<-0.1916,0.8998,-0.1414>,<0.9999997,0.000779,0>
ACTL/<-0.1926,0.9001,-0.1393>,<0.9999983,0.001851,0>
MEAS/LINE,2,WORKPLANE
HIT/BASIC,NORMAL,<-0.1916,0.8998,-0.1408>,<-0.0007723,0.9999997,0>,<-0.1926,0.9001,-0.1385>,USE THEO=YES
HIT/BASIC,NORMAL,<0.2294,0.9001,-0.1419>,<-0.0007723,0.9999997,0>,<0.2272,0.9008,-0.1401>,USE THEO=YES
ENDMEAS/

BORE =FEAT/CIRCLE,CARTESIAN,IN,LEAST_SQR
THEO/<0,-0.0001,-0.0857>,<0,0,1>,0.9387
ACTL/<0,-0.0001,-0.0845>,<0,0,1>,0.9385
MEAS/CIRCLE,4,WORKPLANE
HIT/BASIC,NORMAL,<0.0055,0.4688,-0.0853>,<-0.0117221,-0.9999313,0>,<0.0057,0.4686,-0.0843>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0083,-0.4689,-0.0861>,<0.0179005,0.9998398,0>,<-0.0086,-0.4684,-0.0846>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.4658,-0.0608,-0.0847>,<0.9916206,0.1291842,0>,<-0.4659,-0.0621,-0.0837>,USE THEO=YES
HIT/BASIC,NORMAL,<0.4637,-0.0757,-0.0869>,<-0.9869764,0.1608653,0>,<0.4643,-0.0726,-0.0855>,USE THEO=YES
ENDMEAS/

GAS TUBE =FEAT/CYLINDER,CARTESIAN,IN,LEAST_SQR
THEO/<-0.0018,0.6252,-0.0703>,<-0.0000204,0.0025611,-0.9999967>,0.1831,0.0864
ACTL/<-0.0027,0.6251,-0.0692>,<-0.0000406,-0.0026846,-0.9999964>,0.1829,0.0867
MEAS/CYLINDER,12
HIT/BASIC,NORMAL,<0.0019,0.7165,-0.0272>,<-0.0397717,-0.9992055,-0.0025583>,<-0.0022,0.7164,-0.0261>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0076,0.5338,-0.0274>,<0.0644409,0.9979183,0.0025545>,<-0.0049,0.5341,-0.0262>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0907,0.6034,-0.0272>,<0.971627,0.2365179,0.000586>,<-0.0929,0.6089,-0.0262>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0866,0.6007,-0.0274>,<-0.9641769,0.2652592,0.000699>,<0.0869,0.6058,-0.0264>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0193,0.7142,-0.0735>,<-0.2301759,-0.9731459,-0.0024877>,<0.0134,0.715,-0.072>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0167,0.5356,-0.0738>,<-0.2014683,0.9794918,0.0025127>,<0.011,0.5347,-0.0723>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0911,0.6051,-0.0735>,<0.9757509,0.2188832,0.0005407>,<-0.0932,0.6108,-0.0723>,USE THEO=YES
HIT/BASIC,NORMAL,<0.087,0.6025,-0.0738>,<-0.9687836,0.247907,0.0006546>,<0.0872,0.6078,-0.0725>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.091,0.6051,-0.1133>,<0.9753543,0.2206438,0.0005452>,<-0.0928,0.6092,-0.1118>,USE THEO=YES
HIT/BASIC,NORMAL,<-0.0235,0.7142,-0.1132>,<0.2376487,-0.971348,-0.0024926>,<-0.0175,0.7151,-0.1125>,USE THEO=YES
HIT/BASIC,NORMAL,<0.088,0.6433,-0.1135>,<-0.9804665,-0.1966855,-0.0004838>,<0.0882,0.6356,-0.1126>,USE THEO=YES
HIT/BASIC,NORMAL,<0.0177,0.5358,-0.1135>,<-0.211973,0.9772723,0.0025072>,<0.0107,0.5346,-0.1123>,USE THEO=YES
ENDMEAS/



ENDMEAS/

DIM RAIL= 2D DISTANCE FROM CIRCLE BORE TO LINE TOP OF RAIL PAR TO XAXIS,NO_RADIUS UNITS=IN,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
M 0.9000 0.0100 -0.0100 0.0173 -0.8827 -0.8727 <--------
DIM LOC2= LOCATION OF CYLINDER GAS TUBE UNITS=IN ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
DIM DIST2= 2D DISTANCE FROM CIRCLE BORE TO CYLINDER GAS TUBE PAR TO YAXIS,NO_RADIUS UNITS=IN,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
M 0.6250 0.0030 -0.0030 0.0000 -0.6250 -0.6220 <--------
DIM DIST3= 2D DISTANCE FROM CIRCLE BORE TO LINE RIGHT SIDE (CENTER TO CENTER),NO_RADIUS UNITS=IN,$
0.0050(orig .614)-0.0050 0.6140 0.0000 0.0000 ----#----

Children

No Data