This is a process I have used for the past 15+ years. We use an "L" bracket on every CMM which the corner and CMM table are used as an origin then saved as an External Alignment we call "Locator"
Our template program recalls this alignment and the operator can manually measure (tape line) from the "Locator" to the part origin (per setup sheet). This gives the operator the freedom to place the part anywhere on the CMM so long as the orientation is correct. Rarely does the operator have to use the controller (joy stick) and we never ever ever take manual points.
STARTUP =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
ALIGNMENT/END
$$ NO,
RH 8/11/2022 PC-DMIS 2022R1
FORMAT/ ,OPTIONS, ,HEADINGS, , ;MEAS,NOM,DEV,TOL,OUTTOL, ,
LOADPROBE/SM25-2_5X50
TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
RECALL/ALIGNMENT,EXTERNAL,LOCATOR
L1 =LABEL/
C1 =COMMENT/YESNO,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,OVC=NO,
DO YOU WANT TO VIEW SET UP?
IF/C1.INPUT == "NO"
GOTO/START
END_IF/
COMMENT/OPER,NO,FULL SCREEN=YES,AUTO-CONTINUE=NO,OVC=NO,
SETUP
WORKPLANE/ZPLUS
START =LABEL/
C6 =COMMENT/INPUT,YES,FULL SCREEN=NO,
'CMM #'
C20 =COMMENT/INPUT,YES,FULL SCREEN=NO,
PART NUMBER
C21 =COMMENT/INPUT,YES,FULL SCREEN=NO,
REVISION
C3 =COMMENT/INPUT,YES,FULL SCREEN=NO,
'Work Order\PO # ?'
C4 =COMMENT/INPUT,YES,FULL SCREEN=NO,
'Clock #?'
C5 =COMMENT/INPUT,YES,FULL SCREEN=NO,
'Serial #'
OPTIONPROBE/MAXFORCE=0.15,LOWFORCE=0.025,UPPERFORCE=0.075,TRIG GERFORCE=0.05,
PROBEACCURACY=0.1,POSACCURACY=0.1,#RETURNDATA=10,
RETURNSPEED=1,SCANPNTDENSITY=20,
SCANACCELERATION=10,SCANOFFSETFORCE=0.12,
PROBINGMODE=DFL,MANFINEPROBING=NO
MOVESPEED/ 50
TOUCHSPEED/ 2
PREHIT/1
RETRACT/1
FLY/ON
DISPLAYPRECISION/5
C15 =COMMENT/YESNO,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,OVC=NO,
ENTER LOCATOR POSITION?
IF/C15.INPUT == "NO"
GOTO/
END_IF/
C9 =COMMENT/INPUT,NO,FULL SCREEN=NO,
X DISTANCE FROM LOCATOR
C7 =COMMENT/INPUT,NO,FULL SCREEN=NO,
INPUT PART ZERO
Y DISTANCE FROM LOCATOR
C8 =COMMENT/INPUT,NO,FULL SCREEN=NO,
INPUT PART ZERO
Z DISTANCE FROM TABLE
WORKPLANE/ZPLUS
ASSIGN/V7=C9.INPUT
ASSIGN/V8=C7.INPUT
ASSIGN/V9=C8.INPUT
WORKPLANE/ZPLUS
L2 =LABEL/
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,OVC=NO,
DCC MODE
ASSIGN/V10=1
MODE/DCC
F1 =GENERIC/POINT,INDEPENDENT,CARTESIAN,$
NOM/XYZ,<0*1,0*1,0*1>,$
MEAS/XYZ,<V7,V8,V9>,$
NOM/IJK,<0*1,0*1,V10>,$
MEAS/IJK,<0*1,0*1,V10>
A2 =ALIGNMENT/START,RECALL:LOCATOR,LIST=YES
ALIGNMENT/TRANS,XAXIS,F1
ALIGNMENT/TRANS,YAXIS,F1
ALIGNMENT/TRANS,ZAXIS,F1
ALIGNMENT/END
