Masking datum position in xact measure V2016

BKulpa over 2 years ago

I don't want the datum position to show on the report confusing the operators.
How do I turn it off?

Attached Files

Parents

BKulpa over 2 years ago

After adding a reference DRF for Datum D it only works on the top circle, bottom circle still showing out of spec.

REF_PISTON_DRF =POSITION : PISTON_CYL
            FEATCTRLFRAME/SHOWNOMS=NO,SHOWPARAMS=NO,SHOWEXPANDED=NO
              SIZE TOLERANCES/1,DIAMETER,14.042,0.01,0.01
              PRIMARY DIMENSION/POSITION,DIAMETER,0.25,MMC,,,A,B,MMC,C,
              NOTE/REF_PISTON_DRF
            FEATURES/PISTON_CYL,,
            DIMINFO/REF_PISTON_DRF;ICON,DIMID,FEATID,VERT,HORIZ, ,$
                    HEADINGS,GRAPH AXIS;MEAS, , , , , , , ,
DATUM_AD_AL=ALIGNMENT/START,RECALL[emoticon:6D505171FAA4497C85C5CA27290C555D]ATUM_TUV_AL1,LIST=YES
              ALIGNMENT/LEVEL,YMINUS,DATUM_A_PLN2
              ALIGNMENT/ROTATE,ZPLUS,TO,PISTON_CYL,ABOUT,YMINUS
              ALIGNMENT/TRANS,XAXIS,PISTON_CYL
              ALIGNMENT/TRANS,YAXIS,DATUM_A_PLN2
            ALIGNMENT/END
D11_12_TOP =POSITION : RACK_TOP_CIR
            FEATCTRLFRAME/SHOWNOMS=YES,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=5.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=MM
            COMPOSITE=NO,FIT TO DATUMS=YES,DEV PERPEN CENTERLINE=ON,OUTPUT ALIGNMENT=Current Alignment
            CUSTOMIZED DRF=NO
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,5.64,0.03,0.03
              PRIMARY DIMENSION/POSITION,DIAMETER,0.35,MMC,A,D,MMC,<size>,<dat>
              SECONDARY DIMENSION/<Dim>,<tol>,MMC,<dat>,<dat>,<dat>
              NOTE/D11_12_TOP
            FEATURES/RACK_TOP_CIR,,
            RACK_TOP_CIR
             X:NOM=13.3
             Y:NOM=11.37
            <NEW>
            DIMINFO/D11_12_TOP;ICON,DIMID,FEATID,VERT,HORIZ, ,$
                    HEADINGS,GRAPH AXIS;MEAS, , , , , , , ,
D11_12_BOTT =POSITION : RACK_BOTT_CIR
            FEATCTRLFRAME/SHOWNOMS=YES,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=POSITION,REPORTGRAPH=OFF,TEXT=OFF,MULT=100.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=MM
            COMPOSITE=NO,FIT TO DATUMS=YES,DEV PERPEN CENTERLINE=ON,OUTPUT ALIGNMENT=Current Alignment
            CUSTOMIZED DRF=NO
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,5.64,0.03,0.03
              PRIMARY DIMENSION/POSITION,DIAMETER,0.35,MMC,A,D,MMC,<size>,<dat>
              SECONDARY DIMENSION/<Dim>,<tol>,MMC,A,D,MMC,<size>,<dat>
              NOTE/D11_12_BOTT
            FEATURES/RACK_BOTT_CIR,,
            RACK_BOTT_CIR
             X:NOM=13.3
             Y:NOM=11.37
            <NEW>

Reply

BKulpa over 2 years ago

After adding a reference DRF for Datum D it only works on the top circle, bottom circle still showing out of spec.

REF_PISTON_DRF =POSITION : PISTON_CYL
            FEATCTRLFRAME/SHOWNOMS=NO,SHOWPARAMS=NO,SHOWEXPANDED=NO
              SIZE TOLERANCES/1,DIAMETER,14.042,0.01,0.01
              PRIMARY DIMENSION/POSITION,DIAMETER,0.25,MMC,,,A,B,MMC,C,
              NOTE/REF_PISTON_DRF
            FEATURES/PISTON_CYL,,
            DIMINFO/REF_PISTON_DRF;ICON,DIMID,FEATID,VERT,HORIZ, ,$
                    HEADINGS,GRAPH AXIS;MEAS, , , , , , , ,
DATUM_AD_AL=ALIGNMENT/START,RECALL[emoticon:6D505171FAA4497C85C5CA27290C555D]ATUM_TUV_AL1,LIST=YES
              ALIGNMENT/LEVEL,YMINUS,DATUM_A_PLN2
              ALIGNMENT/ROTATE,ZPLUS,TO,PISTON_CYL,ABOUT,YMINUS
              ALIGNMENT/TRANS,XAXIS,PISTON_CYL
              ALIGNMENT/TRANS,YAXIS,DATUM_A_PLN2
            ALIGNMENT/END
D11_12_TOP =POSITION : RACK_TOP_CIR
            FEATCTRLFRAME/SHOWNOMS=YES,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=OFF,REPORTGRAPH=OFF,TEXT=OFF,MULT=5.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=MM
            COMPOSITE=NO,FIT TO DATUMS=YES,DEV PERPEN CENTERLINE=ON,OUTPUT ALIGNMENT=Current Alignment
            CUSTOMIZED DRF=NO
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,5.64,0.03,0.03
              PRIMARY DIMENSION/POSITION,DIAMETER,0.35,MMC,A,D,MMC,<size>,<dat>
              SECONDARY DIMENSION/<Dim>,<tol>,MMC,<dat>,<dat>,<dat>
              NOTE/D11_12_TOP
            FEATURES/RACK_TOP_CIR,,
            RACK_TOP_CIR
             X:NOM=13.3
             Y:NOM=11.37
            <NEW>
            DIMINFO/D11_12_TOP;ICON,DIMID,FEATID,VERT,HORIZ, ,$
                    HEADINGS,GRAPH AXIS;MEAS, , , , , , , ,
D11_12_BOTT =POSITION : RACK_BOTT_CIR
            FEATCTRLFRAME/SHOWNOMS=YES,SHOWPARAMS=YES,SHOWEXPANDED=YES
            CADGRAPH=POSITION,REPORTGRAPH=OFF,TEXT=OFF,MULT=100.00,ARROWDENSITY=100,OUTPUT=BOTH,UNITS=MM
            COMPOSITE=NO,FIT TO DATUMS=YES,DEV PERPEN CENTERLINE=ON,OUTPUT ALIGNMENT=Current Alignment
            CUSTOMIZED DRF=NO
            STANDARDTYPE=ASME_Y14_5
              SIZE TOLERANCES/1,DIAMETER,5.64,0.03,0.03
              PRIMARY DIMENSION/POSITION,DIAMETER,0.35,MMC,A,D,MMC,<size>,<dat>
              SECONDARY DIMENSION/<Dim>,<tol>,MMC,A,D,MMC,<size>,<dat>
              NOTE/D11_12_BOTT
            FEATURES/RACK_BOTT_CIR,,
            RACK_BOTT_CIR
             X:NOM=13.3
             Y:NOM=11.37
            <NEW>

Children

JacobCheverie over 2 years ago in reply to BKulpa

Are RACK_TOP_CIR and RACK_BOTT_CIR two circles from a single cylindrical feature? If so, try constructing the cylinder and requesting the position of that.

Technically, you should be evaluating both of those FCF's simultaneously.

Where is your datum shift table on the report?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel