I have a problem evaluating a runout. It gives me the error message "this tolerance requires a data to be measured in circular cross sections".
But my auto cylinder is circular...
Your Products have been synced, click here to refresh
START =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
ALIGNMENT/END
MODE/MANUAL
PREHIT/2
RETRACT/2
MOVESPEED/ 200
FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;NOM,TOL,MEAS,DEV,OUTTOL, ,
LOADPROBE/TP20_D2_30
TIP/T1A90B0, SHANKIJK=0, 1, 0, ANGLE=180
WORKPLANE/YPLUS
COMMENT/OPER,NO,FULL SCREEN=NO,AUTO-CONTINUE=NO,OVC=NO,
1. Ebene vorne am Teil
2. DRM 164
3. Linie unten
4 Linie oben
EBENE1 =FEAT/PLANE,CARTESIAN,TRIANGLE
THEO/<186.232,458.429,-519.823>,<0,1,0>
ACTL/<198.013,457.999,-525.659>,<0,1,0>
MEAS/PLANE,3
HIT/BASIC,NORMAL,<176.793,458.426,-610.03>,<0,1,0>,<189.091,458.21,-458.059>,USE THEO=YES
HIT/BASIC,NORMAL,<146.041,458.416,-471.507>,<0,1,0>,<274.973,457.651,-559.459>,USE THEO=YES
HIT/BASIC,NORMAL,<235.863,458.446,-477.932>,<0,1,0>,<129.975,458.137,-559.46>,USE THEO=YES
ENDMEAS/
KREIS1 =FEAT/CIRCLE,CARTESIAN,OUT,LEAST_SQR
THEO/<188.304,456.122,-535.144>,<0,1,0>,163.935,0
ACTL/<202.58,455.87,-535.005>,<0,1,0>,164.148,0
MEAS/CIRCLE,3,YPLUS
HIT/BASIC,NORMAL,<153.38,456.153,-460.989>,<-0.4260775,0,0.9046867>,<205.934,455.783,-452.999>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<269.661,456.328,-525.162>,<0.9925576,0,0.1217759>,<120.618,456.323,-539.294>,USE THEO=YES
MOVE/CIRCULAR
HIT/BASIC,NORMAL,<111.267,455.884,-563.143>,<-0.9398497,0,-0.3415884>,<284.542,455.503,-539.292>,USE THEO=YES
ENDMEAS/
LIN1 =FEAT/LINE,CARTESIAN,UNBOUNDED
THEO/<218.853,422.009,-550.937>,<1,0,0>
ACTL/<236.377,422.185,-554.672>,<0.9965071,0,-0.0835076>
MEAS/LINE,2,YPLUS
HIT/BASIC,NORMAL,<218.853,422.009,-550.937>,<0.0859269,0,0.9963014>,<236.377,422.186,-554.672>,USE THEO=YES
HIT/BASIC,NORMAL,<230.338,422.009,-551.927>,<0.0859269,0,0.9963014>,<249.578,422.184,-555.779>,USE THEO=YES
ENDMEAS/
LIN2 =FEAT/LINE,CARTESIAN,UNBOUNDED
THEO/<220.858,421.82,-518.833>,<1,0,0>
ACTL/<231.502,423.407,-515.673>,<0.9968915,0,0.0787861>
MEAS/LINE,2,YPLUS
HIT/BASIC,NORMAL,<220.858,421.82,-518.833>,<0.0878861,0,-0.9961305>,<231.502,421.833,-515.673>,USE THEO=YES
HIT/BASIC,NORMAL,<232.139,421.82,-517.838>,<0.0878861,0,-0.9961305>,<247.728,424.981,-514.391>,USE THEO=YES
ENDMEAS/
LIN3 =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
THEO/<219.856,421.914,-534.885>,<1,0,0>
ACTL/<233.915,422.802,-534.971>,<0.9999972,0,-0.0023686>
CONSTR/LINE,MID,LIN1,LIN2
A1 =ALIGNMENT/START,RECALL:START,LIST=YES
ALIGNMENT/LEVEL,YPLUS,EBENE1
ALIGNMENT/ROTATE,XPLUS,TO,LIN3,ABOUT,YPLUS
ALIGNMENT/TRANS,XAXIS,KREIS1
ALIGNMENT/TRANS,ZAXIS,KREIS1
ALIGNMENT/TRANS,YAXIS,EBENE1
ALIGNMENT/END
MODE/DCC
CLEARP/YPLUS,5,YPLUS,0,ON
MOVE/CLEARPLANE
EB_CNC =FEAT/CONTACT/PLANE/DEFAULT,CARTESIAN,NONE,LEAST_SQR
THEO/<0,0,0>,<0,1,0>
ACTL/<0.008,-0.001,-0.008>,<0.0030429,0.9999947,-0.001131>
TARG/<0,0,0>,<0,1,0>
ANGLE VEC=<1,0,0>,RADIAL
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=13,NUMROWS=1
SPACER=76
AVOIDANCE MOVE=NO
SHOW HITS=NO
A2 =ALIGNMENT/START,RECALL:A1,LIST=YES
ALIGNMENT/LEVEL,YPLUS,EBENE1
ALIGNMENT/TRANS,YAXIS,EBENE1
ALIGNMENT/END
MOVE/CLEARPLANE
D_164 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
THEO/<0,-2,0>,<0,1,0>,164,0
ACTL/<0.001,-2.04,0.214>,<0.003357,0.9999908,-0.0026679>,163.823,0
TARG/<0,-2,0>,<0,1,0>
START ANG=-25,END ANG=285
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=16,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/CLEARPLANE
A3 =ALIGNMENT/START,RECALL:START,LIST=YES
ALIGNMENT/LEVEL,YPLUS,EB_CNC
ALIGNMENT/ROTATE,XPLUS,TO,LIN3,ABOUT,YPLUS
ALIGNMENT/TRANS,XAXIS,D_164
ALIGNMENT/TRANS,ZAXIS,D_164
ALIGNMENT/TRANS,YAXIS,EB_CNC
ALIGNMENT/END
MOVE/CLEARPLANE
PREHIT/4
RETRACT/4
D_144 =FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,-1,0>,<0,1,0>,144,5
ACTL/<-0.028,-1.001,-0.204>,<0.004486,0.9999682,-0.0065975>,144.069,5
TARG/<0,-1,0>,<0,1,0>
START ANG=0,END ANG=360
ANGLE VEC=<0,1,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=17,NUMLEVELS=3,DEPTH=0,END OFFSET=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/CLEARPLANE
D144 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,-1,0>,<0,1,0>,144
ACTL/<-0.016,-1,-0.19>,<0,1,0>,144.126
TARG/<0,-1,0>,<0,1,0>
START ANG=5,END ANG=355
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=21,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/CLEARPLANE
PREHIT/2
RETRACT/2
D_24 =FEAT/CONTACT/CYLINDER/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,-40,0>,<0,1,0>,24,5
ACTL/<-0.078,-40.002,-0.286>,<-0.0003351,0.999969,-0.0078609>,24.355,5
TARG/<0,-40,0>,<0,1,0>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=17,NUMLEVELS=3,DEPTH=0,END OFFSET=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/CLEARPLANE
CLEARP/XPLUS,101,YPLUS,5,ON
MOVE/CLEARPLANE
TIP/T1A90B-90, SHANKIJK=1, 0, -0.001, ANGLE=-89.904
WORKPLANE/XPLUS
MOVE/CLEARPLANE
SENKUNG_74 =FEAT/CONTACT/PLANE/DEFAULT,CARTESIAN,NONE,LEAST_SQR
THEO/<74,-27.5,0>,<1,0,0>
ACTL/<73.931,-27.489,0.002>,<0.9999232,-0.0122245,-0.0020214>
TARG/<74,-27.5,0>,<1,0,0>
ANGLE VEC=<1,0,0>,RADIAL
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=13,NUMROWS=1
SPACER=12
AVOIDANCE MOVE=NO
SHOW HITS=NO
MOVE/CLEARPLANE
MOVE/POINT,NORMAL,<101,-27.5,200>
CLEARP/YMINUS,-147,XPLUS,101,ON
MOVE/CLEARPLANE
TIP/T1A90B180, SHANKIJK=0, -1, -0.002, ANGLE=179.944
WORKPLANE/YMINUS
MOVE/CLEARPLANE
A4 =ALIGNMENT/START,RECALL:A3,LIST=YES
ALIGNMENT/TRANS,YAXIS,TIEFE_37.5
ALIGNMENT/END
D_22_1.5 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,1.5,0>,<0,-1,0>,22
ACTL/<-0.07,1.5,-0.26>,<0,-1,0>,22.072
TARG/<0,1.5,0>,<0,-1,0>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=72,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/CLEARPLANE
D_22_3 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,3,0>,<0,-1,0>,22
ACTL/<-0.073,3,-0.263>,<0,-1,0>,22.061
TARG/<0,3,0>,<0,-1,0>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=72,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/CLEARPLANE
D_22_5.5 =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
THEO/<0,5.5,0>,<0,-1,0>,22
ACTL/<-0.073,5.5,-0.261>,<0,-1,0>,22.045
TARG/<0,5.5,0>,<0,-1,0>
START ANG=0,END ANG=360
ANGLE VEC=<1,0,0>
DIRECTION=CCW
SHOW FEATURE PARAMETERS=NO
SHOW CONTACT PARAMETERS=YES
NUMHITS=72,DEPTH=0,PITCH=0
SAMPLE METHOD=SAMPLE_HITS
SAMPLE HITS=0,SPACER=0
AVOIDANCE MOVE=NO
FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
SHOW HITS=NO
MOVE/CLEARPLANE
RECALL/ALIGNMENT,INTERNAL,A3
CLEARP/ZPLUS,93,YMINUS,-147,ON
MOVE/CLEARPLANE
TIP/T1A0B0, SHANKIJK=0.001, -0.002, 1, ANGLE=-0.02
WORKPLANE/ZPLUS
MOVE/CLEARPLANE
WORKPLANE/YPLUS
A_ABC =ALIGNMENT/START,RECALL:START,LIST=YES
ALIGNMENT/LEVEL,YPLUS,EB_CNC
ALIGNMENT/ROTATE,XPLUS,TO,SENKUNG_74,ABOUT,YPLUS
ALIGNMENT/TRANS,XAXIS,D_164
ALIGNMENT/TRANS,ZAXIS,D_164
ALIGNMENT/TRANS,YAXIS,EB_CNC
ALIGNMENT/END
D22 =FEAT/CYLINDER,CARTESIAN,IN,LEAST_SQR,NO
THEO/<0,-54,0>,<0,1,0>,22,4
ACTL/<-0.064,-53.682,-0.221>,<-0.0008399,0.9999992,-0.0009762>,22.059,4.013
CONSTR/CYLINDER,BFRE,D_22_1.5,D_22_3,D_22_5.5,,
DATDEF/A,FEATURES=D_164,,
DATDEF/AB,FEATURES=D22,,
COMMENT/REPT,
SCHNITT M-M
COMMENT/REPT,
Ø144 + 0.1 mit Rundlauf 0.65 zu AB
DIM LAGE1= LOCATION OF CYLINDER D_144 UNITS=MM ,$
GRAPH=OFF TEXT=OFF MULT=10.00 OUTPUT=BOTH HALF ANGLE=NO
AX NOMINAL +TOL -TOL MEAS DEV OUTTOL
D 144.000 0.100 0.000 144.069 0.069 0.000 -#
END OF DIMENSION LAGE1
FCFRUNDL1 =GEOMETRIC_TOLERANCE/STANDARD=ISO 1101,SHOWEXPANDED=YES,
FEATURE_MATH=DEFAULT,DATUM_MATH=DEFAULT,
UNITS=MM,OUTPUT=BOTH,ARROWDENSITY=100,
SIZE/NOMINAL=144,TOLERANCE SPECIFICATION MODE=NOMINAL_WITH_DEVIATIONS,
UPPER TOLERANCE=0.1,LOWER TOLERANCE=0,
D144:
MIN LOCAL SIZE:144.028,
MAX LOCAL SIZE:144.308,
SEGMENT_1,CIRCULAR_RUNOUT,0.65,AB,<dat>,
TEXT=OFF,CADGRAPH=OFF,REPORTGRAPH=OFF,MULT=10,
NOMINAL:
HALF ANGLE=0,
MEASURED:
D144:0.360,
DATUMS/REPORTDATUMSIZE=OFF,
AB(D22):NOM=22,+Tol=0.01,-Tol=-0.01,
FEATURES/D144,,
| © 2024 Hexagon AB and/or its subsidiaries. | Privacy Policy | Cloud Services Agreement |