Checking an CWW circle

can you post the code ?

(no subject).eml

ok thank you ill let you know if I've fixed it !

STARTUP    =ALIGNMENT/START,RECALL:USE_PART_SETUP,LIST=YES
            ALIGNMENT/END
            MODE/MANUAL
            PREHIT/0.001
            RETRACT/0.001
            FORMAT/TEXT,OPTIONS, ,HEADINGS,SYMBOLS, ;MEAS,NOM,TOL,DEV,OUTTOL, , 
            TEMPCOMP/METHOD = AUTOMATIC,MATERIAL = Zerodur; Nexcera,CTE=0
              ,SET WARNING LIMIT = FALSE,MINIMUM = 10,MAXIMUM = 40
              ,PART SENSOR NUM=DEFAULT,X SCALE= 25.6566,Y SCALE= 25.2152,Z SCALE= 25.9439,PART TEMP=25.4915
            LOADPROBE/SPHERE PROBE
            TIP/T1A0B0, SHANKIJK=0, 0, 1, ANGLE=0
            MANRETRACT/0.02
MAN_ALIGN  =GROUP/SHOWALLPARAMS=YES
PLN1         =FEAT/PLANE,CARTESIAN,TRIANGLE
              THEO/<-0.0144,0.0352,0.032>,<0,0,1>
              ACTL/<5.5957,3.0992,-15.1783>,<-0.0002403,-0.0033879,0.9999942>
              MEAS/PLANE,4
                HIT/BASIC,NORMAL,<-0.4804,0.1425,0.032>,<0,0,1>,<5.1306,3.2108,-15.1782>,USE THEO=YES
                HIT/BASIC,NORMAL,<-0.4858,-0.095,0.032>,<0,0,1>,<5.1306,2.9789,-15.1787>,USE THEO=YES
                MOVE/POINT,NORMAL,<0.459,0.1818,0.0624>
                HIT/BASIC,NORMAL,<0.4496,-0.0883,0.032>,<0,0,1>,<6.0608,2.979,-15.1788>,USE THEO=YES
                HIT/BASIC,NORMAL,<0.459,0.1818,0.032>,<0,0,1>,<6.0608,3.2279,-15.1776>,USE THEO=YES
              ENDMEAS/
CIR1         =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
              THEO/<0,0,0.1164>,<0,0,1>,0.725,0
              ACTL/<5.5871,3.1105,0.1164>,<0,0,1>,0.7275,0
              TARG/<0,0,0.1164>,<0,0,1>
              START ANG=0,END ANG=360
              ANGLE VEC=<1,0,0>
              DIRECTION=CCW
              SHOW FEATURE PARAMETERS=YES
                VOID DETECTION=NO
                REMEASURE=NO
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=5,DEPTH=-0.04,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0
                AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<0.3625,0,0.0764>,<1,0,0>,<5.9516,3.123,-15.14>
                HIT/BASIC,<0.112,0.3448,0.0764>,<0.309017,0.9510565,0>,<5.7174,3.4478,-15.1386>
                HIT/BASIC,<-0.2933,0.2131,0.0764>,<-0.809017,0.5877853,0>,<5.3127,3.3532,-15.1455>
                HIT/BASIC,<-0.2933,-0.2131,0.0764>,<-0.809017,-0.5877853,0>,<5.2815,2.9183,-15.1454>
                HIT/BASIC,<0.112,-0.3448,0.0764>,<0.309017,-0.9510565,0>,<5.4471,2.7734,-15.1454>
              ENDMEAS/
CIR2         =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
              THEO/<0.625,0,0.032>,<0,0,1>,0.134
              ACTL/<6.2157,3.1099,0.032>,<0,0,1>,0.1334
              TARG/<0.625,0,0.032>,<0,0,1>
              START ANG=0,END ANG=360
              ANGLE VEC=<1,0,0>
              DIRECTION=CCW
              SHOW FEATURE PARAMETERS=YES
                VOID DETECTION=NO
                REMEASURE=NO
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=4,DEPTH=0.02,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0
                AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<0.692,0,0.012>,<-1,0,0>,<6.2788,3.1318,-15.2127>
                HIT/BASIC,<0.625,0.067,0.012>,<0,-1,0>,<6.2288,3.1752,-15.2127>
                HIT/BASIC,<0.558,0,0.012>,<1,0,0>,<6.1555,3.1388,-15.2127>
                HIT/BASIC,<0.625,-0.067,0.012>,<0,1,0>,<6.1992,3.0453,-15.2127>
              ENDMEAS/
LIN1         =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
              THEO/<0,0,0.1164>,<0.9910104,0,-0.1337851>
              ACTL/<5.5871,3.1105,0.1164>,<0.9911095,-0.0009167,-0.1330457>
              CONSTR/LINE,BF,3D,CIR1,CIR2,,
              OUTLIER_REMOVAL/OFF,3
              FILTER/OFF,WAVELENGTH=0
A1           =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
                ALIGNMENT/LEVEL,ZPLUS,PLN1
                ALIGNMENT/TRANS,ZAXIS,PLN1
                ALIGNMENT/TRANS,XAXIS,CIR2
                ALIGNMENT/TRANS,YAXIS,CIR2
                ALIGNMENT/ROTATE,XPLUS,TO,LIN1,ABOUT,ZPLUS
              ALIGNMENT/END
              CLEARP/ZPLUS,0.5,ZPLUS,0,ON
            ENDGROUP/ID=MAN_ALIGN
DCC_ALIGN  =GROUP/SHOWALLPARAMS=YES
              MODE/DCC
PLN1         =FEAT/PLANE,CARTESIAN,TRIANGLE
              THEO/<-0.6394,0.0352,0>,<0,0,1>
              ACTL/<-0.6394,0.0353,0.0004>,<0.0004593,-0.0026734,0.9999963>
              MEAS/PLANE,4
                MOVE/CLEARPLANE
                HIT/BASIC,NORMAL,<-1.1054,0.1425,0>,<0,0,1>,<-1.1054,0.1426,0.0006>,USE THEO=YES
                HIT/BASIC,NORMAL,<-1.1108,-0.095,0>,<0,0,1>,<-1.1109,-0.0949,0.0006>,USE THEO=YES
                MOVE/POINT,NORMAL,<-0.0615,0.0948,0.703>
                HIT/BASIC,NORMAL,<-0.1754,-0.0883,0>,<0,0,1>,<-0.1755,-0.0882,-0.0004>,USE THEO=YES
                HIT/BASIC,NORMAL,<-0.166,0.1818,0>,<0,0,1>,<-0.166,0.1819,0.0008>,USE THEO=YES
              ENDMEAS/
              MOVE/CLEARPLANE
              MANRETRACT/0.05
CIR1         =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,OUT,LEAST_SQR
              THEO/<-0.625,0,0.0844>,<0,0,1>,0.725,0
              ACTL/<-0.625,0,0.0844>,<0,0,1>,0.725,0
              TARG/<-0.625,0,0.0844>,<0,0,1>
              START ANG=0,END ANG=360
              ANGLE VEC=<1,0,0>
              DIRECTION=CCW
              SHOW FEATURE PARAMETERS=YES
                VOID DETECTION=NO
                REMEASURE=NO
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                CIRCULAR MOVES=STRAIGHT
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=5,DEPTH=-0.04,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0
                AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<-0.2625,0,0.0444>,<1,0,0>,<-0.2625,0,0.0444>
                HIT/BASIC,<-0.513,0.3448,0.0444>,<0.309017,0.9510565,0>,<-0.513,0.3448,0.0444>
                HIT/BASIC,<-0.9183,0.2131,0.0444>,<-0.809017,0.5877853,0>,<-0.9183,0.2131,0.0444>
                HIT/BASIC,<-0.9183,-0.2131,0.0444>,<-0.809017,-0.5877853,0>,<-0.9183,-0.2131,0.0444>
                HIT/BASIC,<-0.513,-0.3448,0.0444>,<0.309017,-0.9510565,0>,<-0.513,-0.3448,0.0444>
              ENDMEAS/
              MOVE/CLEARPLANE
CIR2         =FEAT/CONTACT/CIRCLE/DEFAULT,CARTESIAN,IN,LEAST_SQR
              THEO/<0,0,0>,<0,0,1>,0.134
              ACTL/<-5.5864,-3.1176,15.2219>,<0.0002356,0.0033883,0.9999942>,0.134
              TARG/<0,0,0>,<0,0,1>
              START ANG=0,END ANG=360
              ANGLE VEC=<1,0,0>
              DIRECTION=CCW
              SHOW FEATURE PARAMETERS=YES
                VOID DETECTION=NO
                REMEASURE=NO
                SURFACE=THICKNESS_NONE,0
                MEASURE MODE=NOMINALS
                RMEAS=NONE,NONE,NONE
                AUTO WRIST=NO
                CIRCULAR MOVES=STRAIGHT
                GRAPHICAL ANALYSIS=NO
                FEATURE LOCATOR=NO,NO,""
              SHOW CONTACT PARAMETERS=YES
                NUMHITS=4,DEPTH=0.02,PITCH=0
                SAMPLE METHOD=SAMPLE_HITS
                SAMPLE HITS=0,SPACER=0
                AVOIDANCE MOVE=BOTH,DISTANCE BEFORE=0.3937,DISTANCE AFTER=0.3937,DIRECTION=ALONG FEATURE VECTOR
                FIND HOLE=DISABLED,ONERROR=NO,READ POS=NO
              SHOW HITS=YES
                HIT/BASIC,<0.067,0,-0.02>,<-1,0,0>,<-5.5194,-3.1176,15.2019>
                HIT/BASIC,<0,0.067,-0.02>,<0,-1,0>,<-5.5865,-3.0507,15.2017>
                HIT/BASIC,<-0.067,0,-0.02>,<1,0,0>,<-5.6534,-3.1177,15.2019>
                HIT/BASIC,<0,-0.067,-0.02>,<0,1,0>,<-5.5863,-3.1847,15.2022>
              ENDMEAS/
LIN1         =FEAT/LINE,CARTESIAN,UNBOUNDED,NO
              THEO/<-0.625,0,0.0844>,<0.9910104,0,-0.1337851>
              ACTL/<-5.5864,-3.1176,15.2219>,<0.3056531,0.1920633,-0.9325706>
              CONSTR/LINE,BF,3D,CIR1,CIR2,,
              OUTLIER_REMOVAL/OFF,3
              FILTER/OFF,WAVELENGTH=0
A1           =ALIGNMENT/START,RECALL:STARTUP,LIST=YES
                ALIGNMENT/LEVEL,ZPLUS,PLN1
                ALIGNMENT/TRANS,ZAXIS,PLN1
                ALIGNMENT/TRANS,XAXIS,CIR2
                ALIGNMENT/TRANS,YAXIS,CIR2
                ALIGNMENT/ROTATE,XPLUS,TO,LIN1,ABOUT,ZPLUS
              ALIGNMENT/END
              CLEARP/ZPLUS,0.5,ZPLUS,0,ON
            ENDGROUP/ID=DCC_ALIGN

when it goes to check cir1 its still running into the part

change Cir1 to IN instead of out. its trying to check it like it's an OD, sometimes my models do the same thing, when i generate auto features for an inside diameter it thinks it's an outside diameter. 

it is an outside diameter check

ohh oops. Bigger prehit then, you're still on .001

PREHIT/0.05
RETRACT/0.05

Ok it now moving away enough but when it goes to hit the second hit it doesn’t go near the part 

either use circular moves, or add clearplanes in between each hit of the auto circle 

CIRCULAR MOVES=STRAIGHT

Also, you shouldnt be naming the features the same thing, you have two cir1's, two pln1's etc. etc. same with alignments 

In the circle auto feature "CIRCULAR MOVES = CIRCULAR" below that line you added. Delete that circular runout. It is in the feature parameters. If it is crashing into the part, adjust your depth too

I’m trying to add what Zafra suggested and that’s what it’s putting 

f9 the feature and add it in that way, or hover over where it says straight and you should have an option to change it to circular

looks like you did that though in the picture, the code was showing it as straight.  if it's still crashing adjust the depth as william suggested. Or put move/clearplane in between each hit. like this 

Crashes right into the part for the 2nd hit

Still crashes 

Whoa, wait. What version of PC-DMIS do you have Zafra? I don't think we can do that in 2021.2. That would be nice.

I’m using 2023.1

I'd assume you can, we did it in 2017 all the time, and now we are on 2023.2. you just have to copy the move/clearplane command, and ctrl+v in between the hits and it puts the clearplanes in there.

just gotta play around with the depths then, bring it up like .005"-.01" or something. not sure what else it can be XD 

I did that but it’s still crashing and the retract is .05 .