The field contents defined by the Q-DAS applications at characteristic level (K2xxx).
K2004 Characteristic Type
| Value | Value Description | Remark |
| 0 | variable | |
| 2 | var/class | variable classified |
| 1 | attribute | |
| 3 | ordinal | |
| 4 | nominal | |
| 5 | ELS - defect type | |
| 6 | ELS |
K2005 Characteristics Class
| Value | Value Description | Remark |
| 4 | critical | |
| 3 | significant | |
| 2 | important | |
| 1 | of sec. Importance | |
| 0 | unimportant |
K2006 Control item
| Value | Value Description | Remark |
| 0 | no documentation required | |
| 1 | DwsA characteristic | |
| 2 | S characteristic | |
| 3 | R characteristic | |
| 4 | R&S characteristic | |
| 5 | A characteristic | |
| 6 | B part | |
| 10 | Special characteristic | |
| 11 | Special characteristic BP 1 | |
| 12 | Special characteristic BP 2 | |
| 13 | Special characteristic BP 1 SPC | |
| 14 | Special characteristic BP 2 SPC | |
| 15 | R1 | |
| 16 | R2 | |
| 17 | 1 | |
| 18 | 2 | |
| 19 | 3 | |
| 20 | 4 | |
| 22 | Documentation required for safety reasons | |
| 23 | Documentation required for certification | |
| 24 | Relevant to production (no documentation required) | |
| 25 | Relevant to manufacturing ( no documentation required) | |
| 26 | Special characteristic F | |
| 27 | Special characteristic L/CoP | |
| 28 | Special characteristic S | |
| 29 | ESD |
K2007 Control Type
| Value | Value Description | Remark |
| 0 | none | |
| 1 | regulated | |
| 2 | manual | |
| 3 | automatic |
K2008 Group Type
| Value | Value Description | Remark |
| 0 | no group | |
| 1 | Logical group | |
| 2 | Positional tolerance | |
| 3 | Measurement uncertainty | |
| 4 | Extrapolation | |
| 5 | Division | |
| 6 | Error log sheet | |
| 8 | BestFitMove group | |
| 9 | Surface study | |
| 10 | 3D positional tolerance | |
| 11 | AFNOR E60-181 max/min | |
| 12 | MMC (Hole) | |
| 13 | MMC (Shaft) | |
| 14 | VDA 5 | |
| 17 | Temperature study | |
| 18 | Unbalance | |
| 19 | Perpendicularity | |
| 20 | Concentricity | |
| 21 | Coaxiality |
|
K2009 Measured quantity
| Value | Value Description | Remark |
| not in current list | ||
| 0 | undefined | |
| 100 | Straightness | |
| 101 | Flatness | |
| 102 | Roundness | |
| 103 | Cylindricity | |
| 104 | Profile of a line | |
| 105 | Profile of a surface | |
| 106 | Angularity | |
| 107 | Perpendicularity | |
| 108 | Parallelism | |
| 109 | True Position (value) | |
| 110 | Concentricity | |
| 111 | Symmetry | |
| 112 | Runout | |
| 113 | Total Runout | |
| 114 | CompCoaxial | |
| 115 | CompPattern | |
| 117 | Coordinates | |
| 118 | Surface Runout | |
| 120 | X coordinate | |
| 121 | Y coordinate | |
| 122 | Z coordinate | |
| 140 | Appraisal number angle area | |
| 145 | Surface finish | |
| 149 | Excavation depth | |
| 150 | Max. profile height Rz | |
| 151 | Total profile height Rt | |
| 152 | Deviation assessed prof. Ra | |
| 153 | Max. profile height Pt | |
| 154 | Profile height Point | |
| 155 | Red. height of centres | |
| 156 | Red. score depth | |
| 157 | Profile Wave depth Wt | |
| 158 | Maximum roughness depth | |
| 159 | Basic roughness depth | |
| 160 | Material proportion Pmr | |
| 161 | Material proportion Mr1 | |
| 162 | Material proportion Mr2 | |
| 170 | Swirl depth | |
| 171 | Swirl angle | |
| 172 | Swirl pitch | |
| 180 | Average dominant waviness | |
| 181 | Max. dominant waviness | |
| 182 | Length of the dominant waviness | |
| 190 | Mean depth of roughness motifs | |
| 191 | Max. depth of profile irregularity | |
| 192 | Mean width of roughness motifs | |
| 200 | Distance | |
| 201 | Radius | |
| 202 | Diameter | |
| 203 | Angle | |
| 204 | Ellipsis minor Ø | |
| 205 | Ellipsis major Ø | |
| 206 | Cone angle | |
| 210 | Spherical measuring rod | |
| 211 | Depth / height of tooth | |
| 220 | Spring rate | |
| 250 | Temperature [°C] | |
| 251 | Temperature [°F] | |
| 255 | Pressure [bar] | |
| 260 | Coating thickness | |
| 270 | Volume | |
| 280 | Mass | |
| 282 | Force | |
| 285 | Hardness | |
| 290 | Viscosity | |
| 292 | Density | |
| 300 | Unbalance | |
| 301 | Torque | |
| 302 | Tightening torque | |
| 303 | Additional torque | |
| 320 | Rotation angle | |
| 350 | Revolution speed | |
| 501 | Resistance | |
| 502 | Capacity | |
| 503 | Inductivity | |
| 504 | Phase shift | |
| 505 | Frequency | |
| 506 | Amperage | |
| 507 | Voltage | |
| 508 | Output | |
| 509 | Field intensity | |
| 601 | Pitch | |
| 602 | Pitch error | |
| 604 | Cumulative pitch bias | |
| 605 | Cumulative pitch error | |
| 607 | Total pitch error | |
| 620 | Line | |
| 621 | Formal line error | |
| 630 | Tooth profile | |
| 631 | Formal profile error | |
| 632 | Profile angle bias | |
| 633 | Profile wobble | |
| 640 | Tip relief | |
| 641 | Profile crowning | |
| 642 | Crowning | |
| 643 | Crowning height | |
| 651 | Flank line angle bias | |
| 652 | Flank line wobble | |
| 660 | Radial run-out | |
| 662 | Wobble | |
| 663 | Coaxiality | |
| 800 | Time | |
| 820 | Noise | |
| 910 | Leak rate | |
| 1001 | Volume porosity global | |
| 1002 | Volume porosity ROI | |
| 1003 | Volume porosity geo | |
| 1004 | Single pore volume | |
| 1005 | Pore diameter | |
| 1006 | Equivalent pore diameter | |
| 1007 | Sphericity | |
| 1008 | Compactness | |
| 1009 | Distance of adjacent pores | |
| 1010 | Distance to surface | |
| 1011 | Number of permitted pores | |
| 955 | Remaining particles | |
| 950 | Cleanliness of component | |
| 810 | Percentage | |
| 805 | Number | |
| 676 | Radial one-roll dimension | |
| 675 | Radial one-ball dimension | |
| 674 | Diametrical two-roll dimension | |
| 673 | Diametrical two-ball dimension | |
| 672 | Contact runout deviation | |
| 671 | Two-flank tooth-to-tooth radial composite deviation | |
| 670 | Two-flank working variation | |
| 661 | Eccentricity | |
| 617 | Space width on the reference cylinder | |
| 612 | Root diameter | |
| 610 | Tip diameter | |
| 609 | Axial pitch variation | |
| 608 | Base pitch variation | |
| 606 | Pitch fluctuation | |
| 380 | Cam height | |
| 372 | Form increase | |
| 370 | Form deviation | |
| 364 | Deviation from rated speed | |
| 362 | Profile error | |
| 360 | Angle error | |
| 311 | 3D note | |
| 310 | 2D note | |
| 275 | Area | |
| 234 | Diameter average | |
| 233 | Diameter minimum | |
| 232 | Diameter maximum | |
| 231 | Squareness | |
| 230 | Width | |
| 218 | Secondary Gear Characteristic | |
| 216 | Span distance (over k teeth or gaps) | |
| 215 | Tooth thickness fluctuation | |
| 214 | Tooth thickness deviation (on the reference cylinder) | |
| 212 | Tooth thickness on the reference cylinder | |
| 208 | Outside diameter | |
| 207 | Inside diameter | |
| 194 | Material proportion tp | |
| 193 | Material proportion Rmr | |
| 139 | Conicity | |
| 132 | Ovality | |
| 125 | Offset |
K2011 Distribution
| Value | Value Description | Remark |
| no distribution | variable characteristics | |
| 100 | Binominal Distribution | attribute characteristic |
| 200 | Poisson Distribution | attribute/ELS characteristic |
K2015 Tool wear type
| Value | Value Description | Remark |
| 0 | undefined | |
| 1 | ascending | |
| 2 | descending |
K2016 100% measurement
| Value | Value Description | Remark |
| 0 | No | |
| 1 | Yes |
K2020 Special conditions
| Value | Value Description | Remark |
| 0 | not defined | |
| 1 | Adjustable tool | |
| 2 | Non-adjustable tool | |
| 3 | Statistically toleranced | |
| 4 | Maximum material condition (MMC) | |
| 5 | Least material condition (LMC) | |
| 6 | Regardless of feature size (RFS) | |
| 101 | Pre-processing dimensions | |
| 102 | Surface texture features | |
| 103 | Waviness features |