Easy5 Community Forum - Easy5

Before You Ask Your Question

Before you ask your question or start a discussion, have you checked our Knowledge Base on SimCompanion or the Product Documentation for Easy5?

Please read our Community Rules

Manage Forum Subscriptions

Not Answered

Are EASY5 models backward compatible with older versions? 0

25 views

0 replies

Started over 7 years ago
by Rick Clanton
Answered

dll file generated by EZ5 in Adams Mechatronic +1

66 views

1 reply

Latest 1 month ago
by Rick Clanton
Answered

Modifying tabular data in a multiprocessing csv file 0

152 views

1 reply

Latest 3 months ago
by Rick Clanton
Answered

Integrator reset +1

181 views

2 replies

Latest 4 months ago
by Rick Clanton
Answered

Hello Everyone, In my project, I used composition poppet type in the valve. However, Easy5 have two type poppets (cone and ball). May I make composition poppet in easy5? Best regards, Samet +1

2709 views

3 replies

Latest 11 months ago
by Rick Clanton
Answered

How to debug Easy5 with Visual Studio? 0

377 views

2 replies

Latest over 3 years ago
by matthew.goit
Answered

I have a user library and am trying to convert it to ascii. I get an error from easy5 saying the xx.ezdc file could not be found. This file clearly exists. I have tried the command line approach and the Library-Convert Library approach. same result +1

2060 views

4 replies

Latest over 3 years ago
by Rick Clanton
Answered

How to import ezanl into another model 0

155 views

1 reply

Latest over 4 years ago
by Rick Clanton
Answered

I am simulating hydraulic hammer using the WP component in the thermal hydraulic library. The resulting transient's damping ratio seems to be incredibly sensitive to the number of segments I define within the component. Which results do I trust? +1

1619 views

2 replies

Latest over 5 years ago
by eric.plevy
Answered

I am using the gas dynamics library to simulate a simple adiabatic compression of a volume of nitrogen. Using the "ideal gas" computation. Just wondering if the ratio of specific heats changes during the calculation as the temperature changes. +1

160 views

1 reply

Latest over 5 years ago
by Rick Clanton
Answered

How to convert Easy5 output to another format? 0

184 views

2 replies

Latest over 5 years ago
by matthew.goit
Answered

Best way to get all parameters in a 2015 easy5 model? 0

121 views

2 replies

Latest over 6 years ago
by TLowery
Answered

Using an “auxfile” To Enter Blocks of Data doesn't work. The block label "$" sign in converted into a "*" in the . exanl file and thus the .ezapl says it is considered as a comment. +1

877 views

1 reply

Latest over 6 years ago
by Rick Clanton
Answered

The Easy5 manuals seem to suggest at the start, that it can interface with Nastran. Is this just on the basis of Nastran &EZ5 both linking to ADAMS? Or something direct? +1

113 views

2 replies

Latest over 6 years ago
by Sas
Answered

Is there a tool to convert .ezrpd files to .csv files? I know for a simulation it is possible to output a csv when running, but I need to convert already run cases. +1

96 views

1 reply

Latest over 6 years ago
by Rick Clanton
Answered

Is there a data reference for Skydrol LD-4 adiabatic tangent bulk modulus? I see in AIR1362B Figure 7 it shows data, but does not seem to match the EASY5 results. And for some reason this plot was removed from RevC of AIR1362. +1

132 views

4 replies

Latest over 7 years ago
by ASettles
Answered

How to remove the derivative of the forcing function term? See attachment for more information. +1

99 views

1 reply

Latest over 7 years ago
by Rick Clanton
Not Answered

Why do my older 32-bit user libraries need to be converted to 64-bit in the newer versions of EASY5? 0

23 views

0 replies

Started over 7 years ago
by Rick Clanton
Answered

How can the velocity status be extracted from the dual acting actuator found in the GD library? +1

100 views

2 replies

Latest over 7 years ago
by cjohnson