Hello everybody:
I want to scan a B_spline curve on a plane .
ScanOnCurve (SRC=PL_1F1_S(1), DST=PL_1F1_SCAN(1), CSY=CSY_1B999_1F, STY=NPT, SPD=SPD, DIS=DNS)
' SRC=PL_1F1_S(1) ' contains many points (more 1000 numbers)
I find a question,It…
I just installed the offline seed of pcdmis 2012.When I click on any of the dimensioning icons (flatness, true position, perpindicularity, etc.) in the feature control frame editor I cannot type in the tolerancing or select my datums because it looks…
I am having an issue once in a while with hole diameters. I am using a 1mm ball to check the the part. This issue comes and go's. I ran a program this morning with true positions and hole diameters and everything checked out. A couple of hours later I…
I am in discussion with another engineer here trying to hash out the calculation for Position of a threaded hole within a bolt circle. The equation works out to be 2*sqrt(x(dev)^2 + y(dev)^2). I am looking for the explaination of how Quindos arrives at…
Hi all,
I have regularly problems with these commands showed in title, the same error appears again and again on the screen: "Value too small (possibly two equal points)!"
I can confirm that I'm not comparing the same points (equal profiles) …
Please see the images. I have taken the basic course, but only use the software a few times a year. Is there anything I can to reduce or stop this?
Image customer sent (two scans taken ~1 year apart):
My image (includes extra that the customer…
We have a Global that we run Quindos and PC DMIS on. The problem is we can't get Quindos up and running after we have ran a DMIS program. We always get a calibration error and we have tried shutting the machine all the way down and rebooting to no avial…
Scanning a 3.125 ring gauge with 5 pts/mm at 10mm/sec. Collecting 255 points in ring gauge. The circum. of the ring gauge is 9.82 in. or 249.428 mm. I am getting ready to scan a 48" dia. and trying to figure
out how set the number of points per/mm to…
Hello all,
Quick question here.
Using ALIGNP1P2(CSY=NEWPART$CSY, NE1=(10,-10), AE1=CIR_1, NE2=(-10,10), AE2=CIR_2)
Are the NE points for reference, or are they defining where the circles are located at?
I would assume that if I am creating…
The process of moving business from another facility to our facility has begun, and a Leitz running Quindos 6 (I don't know what release) will be part of the move. We already have a Leitz running Q7, so questions and ideas are bound to come up -
…
Anyone have any experience in creating custom XML report templates for Q7? Makes PC-DMIS reportdesigner look easy......
Even if I could get my hands on some slightly modified XML files, it would help me to understand what I can/can't mess with when…
Hello everybody,
We have a global image with pcdmis 3.7, and quindos 6, I would like to know, how I can verify if I can measure gears with my quindos? I mean, can I check for license or something like that?
Hope you can help me
Fernando.
We have a shop floor CMM with Quindos 6 on it. I rarely use it, but I seem to be the "go to guy".
Hard drive failure and IT installed a new drive.
I start up the computer and controller, open Quindos and come to the "Select Working Environment…
Leitz PMM866
When moving in y-axis, it halts abruptly and this message appears:
"Error at Transmmitter Signal Y-Axis"
Tried shutting down completely and re-booting, but to no avail. Machin still faults out, but not always in the same location…
Does anyone know how to work out a span dimension (base tangent lenght) e.g. Span over 7 teeth,if I only have the gear information supplied in specification BS3550? Don't have that much experience around gears and have just started programming a Leitz…
This is not a Quindos question but, I can probably get an answer here faster than the CMM forum.
When doing a manual probe change, after the air supply has been shut down, the head will lock but won't allow a manual change with
PC Dmis all versions…
I would like to know if anyone else out there is having stability issues with Quindos 7. It was installed by the vendor again several weeks back and is a mess.
Randomly just errors and shuts down, icons that don't work. I type a value in a box, and…
Hello gentlemen,
When I measure one type of gear (z4, mn1, alpha20 °, beta =- 20 °) Quindos shows me this error. I think this is an error of probe offset (probe cluster TIP DIA 0.8 mm without rotary table) because the machine stops always at the same…
Our Global Image CMM running Q6 to inspect blades has gone down.
The machine seems to lose itself when going around a sharp corner, no matter what the scan speed, and has to "hop" to try to make contact with the part again. Even on lowest speeds,…
