Hello, all!
(I'm ignorant. Tear me apart!)
This is the first time I've come across this type of call out. I understand a bit about how it works, but need help with the execution.
Could someone, please, walk me through the general steps I'd take…
Can anyone advise how to fix a suspect probe calibration result?
I first noticed the positions reported by (2) different probes are off each other by mm.
In the calibration history of the one I see some major change in geometry compared to a few days…
Hi all,
"How can I represent each of the 8 elements that make up a set in a true position?"
I mean, what is the best way to provide information about each element separately when they form a set? Any ideas?
Feature control frame asks Position of ID to Top Plane -A- and -B-. Datum -B- is 3 datum target points all at different radial distances. Would Datum -B- just be reported as separate points or do you combine all 3 for a feature? Thanks for any help.
Good morning,
I have recently set up a program for a welded flange that has a position callout from one welded cylinder to a perpendicular plane(A) and a cylinder (B) located on the flange beyond the welded cylinder .
it has a position of .025…
I'm a bit behind...will someone please point me in the right direction to report boundary type true position? I've used profile to report deviation in the past but I want a more better method...:-\
Has anyone had problems with Xact Measure TP dims? I have various parts with MMC on the DF as well as the Datums. As may be expected the DF and the datums all have different size tolerances. When setting up the dimension I tolerance them correctly, but…
Good morning all,
I have a question in regards to a true position stack up.
I am using a CAD model to probe the part but my Z nominal is incorrect. which should be the nominal distance from plane A to the hole so it is throwing my tolerance off…
Good afternoon all,
I am trying to set up a quick program to measure a true position call out for a part we are running at the shop. it is a small bushing and the TP call out is the O.D. cylinder to the I.D. cylinder (datum A) and a perpendicular…
I recently was tasked with measuring a part bent at an angle with a pattern of holes on both surfaces of the bend. The bottom plane is Datum A, the bottom pattern of holes is Datum B. There is a profile locating all of the edges on the bottom plane to…
I came across a print requirement too inspect TP of an open slot on a circular disk as shown in image attached.
what would be the correct way to inspect this?
I need to inspect TP of Fir-Tree slot with MMC condition.
currently I am inspecting it by a point obtained from intersection line of 2 adjacent planes on fir tree face
the issue here is PC-DMIS doesn't let me apply MMC condition for a point feature…
Hello everyone
I need to inspect TP of a tapered through hole on a cylindrical surface at a distance of R. 10.4 from center of part as shown in image,
any thoughts on how this can be inspected..
Attached Files
Hello everyone!
last week i came across an issue in which first hole was mismarked during production.
The part was similar to attached image with two set of holes 1st set has 30 holes and 2nd has 59, in which 1st hole of both set are inline with each…
I have come across another issue that im having with exact measure ( i have not tried this on "geometric tolerance command" yet). The problem i am having is the datum shift when applied thru simultaneous evaluation (s.e.) is making erroneous datum shifts…
Hey all,
Does anyone know if there is a way to automatically add the bonus tolerance of a position onto the tolerance on the report. It would help out inspectors if the total tolerance was displayed. I don't get why it calculates the total for a position…
Need help!! Not sure why PC-DMIS keeps giving me bad results. I have created different alignments, different hits, different workplanes and views but PC-DMIS still gives me wrong numbers. Any suggestions on what is going on?
On the blueprint I have…
Hi,
i am trying to inspect TP of a point considering only PA (angular variation),
while generating output I'm getting same value wile when considering both PA & PA.
can someone please guide me what's going wrong and how i can generate TP with PA…
is there any code we can use to calculate this from set true position values?
for a circular disk with 60 slots at od.
SPACING ERROR NOT TO EXCEED 0.005 TOTAL.
SPACING ERROR BETWEEN ADJACENT SLOT 0.003 MAX AT 60 PLACES.
1 PLACE MAY BE 0.005 MAX…
Hi guys this is my first post so forgive me if I miss out any information, I'm recently updated to version 2021.1 (from 2020 R2) and am having an issue with positional dimensions in the "text only" report format.
Everything is displayed fine when the…
Currently i am using pcdmis 2019 cad++ when i do the position of certain features it is not calculating bonus to the position feature, when i refresh that fcloc then close the program and reopen that it is calculated but position values changes automatically…
Dear sir,
I have a part having datum A as plane, Datum B&Datum C as circle but the Datum B is with an angle to Datum A, it is not perpendicular to Datum A so when i going to call the position of some circles wrt ABC then a message show as secondary…
Good afternoon,
For a momentary fix I have resorted to using legacy mode to get this to work for now but I really don't want to use legacy mode for 1000+ feature reporting, I'm sure you can sympathize lol
I have been tasked with writing a program…